Sony Power HAD FX HSC300R User manual

HD COLOR CAMERA
HSC300RF
HSC100RF
HSC300R
HSC100R
SERVICE MANUAL
1st Edition

警告
このマニュアルは， サービス専用です。
お客様が， このマニュアルに記載された設置や保守， 点検， 修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため， サービストレーニングを受けた技術者のみご使用ください。
WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HSC300RF/HSC100RF/HSC300R/HSC100R

Model Name Serial No.
HSC300R (UC): Kings Triax
Connector
10001 and Higher
HSC300R (J): Tajimi Triax Con-
nector
30001 and Higher
HSC300R (CED): Fischer Triax
Connector
40001 and Higher
HSC300R (CED): LEMO Triax
Connector
60001 and Higher
HSC300RF (UC): LEMO Opti-
cal Fiber Connector
10001 and Higher
HSC300RF (J): Tajimi Optical
Fiber Connector
30001 and Higher
HSC300RF (CED): LEMO Opti-
cal Fiber Connector
40001 and Higher
HSC300RF (E): Tajimi Optical
Fiber Connector
50001 and Higher
HSC100R (UC): Kings Triax
Connector
10001 and Higher
HSC100R (J): Tajimi Triax Con-
nector
30001 and Higher
HSC100R (CED): Fischer Triax
Connector
40001 and Higher
HSC100R (CED): LEMO Triax
Connector
60001 and Higher
HSC100RF (UC): LEMO Opti-
cal Fiber Connector
10001 and Higher
HSC100RF (J): Tajimi Optical
Fiber Connector
30001 and Higher
HSC100RF (CED): LEMO Opti-
cal Fiber Connector
40001 and Higher
HSC100RF (E): Tajimi Optical
Fiber Connector
50001 and Higher
HSC300RF/HSC100RF/HSC300R/HSC100R

CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
This HD color camera is classified as a CLASS 1 LASER PRODUCT.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HSC300RF/HSC100RF/HSC300R/HSC100R

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type rec-
ommended by the manufacturer.
When you dispose of the battery, you must obey the
law in the relative area or country.
ATTENTION
Il y a danger d’explosion s’il y a remplacement incor-
rect de la batterie. Remplacer uniquement avec
une batterie du même type ou d’un type équivalent
recommandé par le constructeur.
Lorsque vous mettez la batterie au rebut, vous devez
respecter la législation en vigueur dans le pays ou la
région où vous vous trouvez.
VORSICHT
Explosionsgefahr bei Verwendung falscher Batterien.
Batterien nur durch den vom Hersteller empfohlenen
oder einen gleichwertigen Typ ersetzen.
Wenn Sie die Batterie entsorgen, müssen Sie die
Gesetze der jeweiligen Region und des jeweiligen
Landes befolgen.
注意
指定以外の電池に交換すると，破裂する危険があります。
必ず指定の電池に交換してください。
使用済みの電池は，国または地域の法令に従って
処理してください。
FÖRSIKTIGHET!
Fara för explosion vid felaktigt placerat batteri.
Byt endast mot samma eller likvärdig typ av batteri,
enligt tillverkarens rekommendationer.
När du kasserar batteriet ska du följa rådande lagar
för regionen eller landet.
PAS PÅ
Fare for eksplosion, hvis batteriet ikke udskiftes
korrekt.
Udskift kun med et batteri af samme eller tilsvarende
type, som er anbefalet af fabrikanten.
Når du bortskaffer batteriet, skal du følge
lovgivningen i det pågældende område eller land.
HUOMIO
Räjähdysvaara, jos akku vaihdetaan virheellisesti.
Vaihda vain samanlaiseen tai vastaavantyyppiseen,
valmistajan suosittelemaan akkuun.
Noudata akun hävittämisessä oman maasi tai
alueesi lakeja.
FORSIKTIG
Eksplosjonsfare hvis feil type batteri settes i.
Bytt ut kun med samme type eller tilsvarende
anbefalt av produsenten.
Kasser batteriet i henhold til gjeldende avfallsregler.
⊼ᛣ
⊼ᛣ
བᵰ᳈ᤶⱘ⬉∴ϡℷ⹂ˈህӮ᳝⟚⚌ⱘ䰽DŽ
া᳈ᤶৠϔ㉏ൟ៪ࠊ䗴ଚ᥼㤤ⱘ⬉∴ൟোDŽ
໘⧚⬉∴ᯊˈᖙ乏䙉ᅜⳌ݇ഄ៪೑ᆊⱘ⊩ᕟDŽ
HSC300RF/HSC100RF/HSC300R/HSC100R

Table of Contents
Manual Structure
Purpose of this manual....................................................................................................................5
Related manuals...........................................................................................................................5
Trademarks...............................................................................................................................5
1. Service Overview
1-1. Connectors and Cables........................................................................................................1-1
1-1-1. Connector Input/Output Signals........................................................................................1-1
1-1-2. Wiring Diagrams for Cables............................................................................................1-5
1-1-3. Connection Connectors/Cables.........................................................................................1-5
1-1-4. Note in Connecting CCU Connector...................................................................................1-5
1-2. Location of Printed Circuit Boards............................................................................................1-7
1-3. Circuit Description............................................................................................................1-9
1-3-1. Optical System (OHB Block)...........................................................................................1-9
1-3-2. Signal Processing/Transmission System...............................................................................1-9
1-3-3. System Control System...............................................................................................1-10
1-3-4. Power Supply System.................................................................................................1-13
1-4. Notes on Replacement of Parts and Circuit Board...........................................................................1-15
1-4-1. Description on EEPROM Data........................................................................................1-15
1-4-2. Adjustment and Setting Required when Replacing the SY-430 Board ..............................................1-15
1-4-3. Adjustment and Setting Required when Replacing the OHB Assembly..............................................1-16
1-5. Periodic Maintenance and Inspection........................................................................................1-17
1-5-1. Recommended Replacement Parts....................................................................................1-17
1-5-2. Cleaning the Air Vents................................................................................................1-18
1-6. Replacing Lithium Battery...................................................................................................1-19
1-6-1. Note on Replacement of Lithium Battery.............................................................................1-19
1-6-2. Replacing Procedure..................................................................................................1-19
1-7. Cleaning of Connector/Cable................................................................................................1-20
1-7-1. When the Optical Connector Cleaner (Commercially Available) is Available.......................................1-20
1-7-2. When the Optical Connector Cleaner (Commercially Available) is not Available (Connectors/Cables of LEMO) ...1-21
1-7-3. When the Optical Connector Cleaner (Commercially Available) is not Available (Tajimi Electronics Co., Ltd.)...1-22
1-7-4. When the Optical Connector Cleaner (Commercially Available) is not Available (Connector).....................1-24
1-8. Fixtures/Measuring Equipments List........................................................................................1-25
1-8-1. Fixtures................................................................................................................1-25
1-8-2. Measuring Equipments................................................................................................1-25
1-9. Upgrading Software Programs...............................................................................................1-26
1-9-1. Upgrading Camera Application ......................................................................................1-26
1-9-2. Upgrading OS .........................................................................................................1-26
1-10. PLD..........................................................................................................................1-28
1-10-1. Corresponding PLD...................................................................................................1-28
1-10-2. Upgrading PLD Data..................................................................................................1-28
1-11. Forced Version Update......................................................................................................1-30
1-11-1. Forced Version Update of Software or PLD Data....................................................................1-30
1-12. Intercom Settings............................................................................................................1-31
1-12-1. Talk (Microphone) Settings...........................................................................................1-31
1-12-2. Receive (Headphone) Settings........................................................................................1-31
1-13. Flexible Card Wire and Coaxial Cable......................................................................................1-33
1-13-1. Connecting/Disconnecting Flexible Card Wire.......................................................................1-33
HSC300RF/HSC100RF/HSC300R/HSC100R 1

1-13-2. Forming Flexible Card Wire ..........................................................................................1-33
1-13-3. Connecting/Disconnecting Coaxial Cable............................................................................1-34
1-14. Description of CCD Block Number .........................................................................................1-36
1-15. Circuit Protection Parts......................................................................................................1-37
1-15-1. Fuses...................................................................................................................1-37
1-15-2. Circuit Protection Element............................................................................................1-37
1-16. Lead-free Solder.............................................................................................................1-39
2. Replacement of Main Parts
2-1. Inside Panel....................................................................................................................2-1
2-2. Outside Panel Section (TRIAX)...............................................................................................2-2
2-2-1. Outside Panel Assembly (TRIAX).....................................................................................2-2
2-2-2. TX-148 Board (TRIAX)................................................................................................2-3
2-2-3. FL-377 Board/TRIAX CN Assembly (TRIAX)........................................................................2-4
2-3. Outside Panel Section (Fiber).................................................................................................2-7
2-3-1. Outside Panel Assembly (Fiber)........................................................................................2-7
2-4. CCD Section...................................................................................................................2-9
2-4-1. CCD Unit (HSC300R/300RF)..........................................................................................2-9
2-4-2. CCD Unit (HSC100R/100RF)........................................................................................2-11
2-4-3. TG-285 Board.........................................................................................................2-13
2-4-4. DR-675 Board.........................................................................................................2-14
2-4-5. Filter Servo Board/Filter Disk (HSC300R/300RF)...................................................................2-15
2-4-6. PA-418 Board.........................................................................................................2-16
2-4-7. SE-1138 Board (HSC100R/100RF)...................................................................................2-18
2-5. CD-78 Board (HSC300R/100R).............................................................................................2-19
2-6. SDI-117 Board (HSC300RF/100RF)........................................................................................2-20
2-7. DPR-358 Board..............................................................................................................2-21
2-8. DC Fan.......................................................................................................................2-23
2-9. SY-430 Board/AT-189 Board...............................................................................................2-25
2-10. Power Supply Assembly.....................................................................................................2-27
2-11. MB-1207 Board..............................................................................................................2-28
2-12. Connector Panel..............................................................................................................2-30
2-13. Intercom Panel...............................................................................................................2-32
2-14. CN-3647 Board/SW-1608A Board..........................................................................................2-33
3. Electrical Alignment
3-1. Preparations...................................................................................................................3-1
3-1-1. Equipment Required....................................................................................................3-1
3-1-2. Precautions on Adjustments............................................................................................3-1
3-1-3. File Data at Adjustment................................................................................................3-1
3-1-4. Handling the Grayscale Chart..........................................................................................3-2
3-1-5. Setup Menu.............................................................................................................3-3
3-1-6. Connection of Equipment..............................................................................................3-5
3-1-7. Initial Settings..........................................................................................................3-5
3-1-8. Adjustment Items and Setup Menu Items..............................................................................3-6
3-2. Automatic Adjustment........................................................................................................3-8
3-2-1. Execute the Automatic Adjustment....................................................................................3-8
3-3. Electrical Alignment..........................................................................................................3-9
3-3-1. Clamp Level Adjustment between Channel A and Channel B (Black Offset Adjustment)............................3-9
HSC300RF/HSC100RF/HSC300R/HSC100R 2

3-3-2. Black Set Adjustment.................................................................................................3-10
3-3-3. Sensitivity Adjustment................................................................................................3-10
3-3-4. V-SUB Adjustment....................................................................................................3-11
3-3-5. Black Shading Adjustment............................................................................................3-12
3-3-6. White Shading Adjustment............................................................................................3-13
3-4. Video System Level Adjustment............................................................................................3-16
3-4-1. H/V Ratio Adjustment.................................................................................................3-16
3-4-2. Detail Level Adjustment..............................................................................................3-17
3-4-3. Crispening Adjustment................................................................................................3-17
3-4-4. Level Dependent Adjustment.........................................................................................3-18
3-4-5. Detail Clip Adjustment................................................................................................3-19
3-4-6. Auto-iris Adjustment..................................................................................................3-20
3-4-7. Pedestal Level Adjustment............................................................................................3-21
3-4-8. Flare Adjustment......................................................................................................3-21
3-4-9. Gamma Correction Adjustment.......................................................................................3-22
3-4-10. Knee Point/Knee Slope Adjustment...................................................................................3-23
3-4-11. White Clip Level Adjustment.........................................................................................3-24
3-4-12. File Store..............................................................................................................3-25
3-5. ND Offset Adjustment.......................................................................................................3-26
3-5-1. White Balance Compensation.........................................................................................3-26
3-6. RPN Compensation..........................................................................................................3-28
3-6-1. Automatic Compensation (APR)......................................................................................3-28
3-6-2. Manual RPN Compensation Adjustment.............................................................................3-28
3-6-3. Procedures to be Taken when the RPN Compensation Fails.........................................................3-29
3-6-4. Performing Automatic RPN Detection Effectively...................................................................3-31
3-6-5. RPN Compensation Flowchart........................................................................................3-32
4. Digital Triax Transmission System Alignment
4-1. Preparations...................................................................................................................4-1
4-1-1. Equipment Required....................................................................................................4-1
4-1-2. Precautions on Adjustments............................................................................................4-1
4-2. 1.4-MHz Modulation Circuit Adjustment.....................................................................................4-2
4-2-1. Frequency Adjustment..................................................................................................4-2
4-3. Demodulation Circuit Adjustment............................................................................................4-3
4-3-1. Tuning Adjustment.....................................................................................................4-3
5. File System
5-1. File Structure..................................................................................................................5-1
5-1-1. Structure of Paint Related Files.........................................................................................5-2
5-2. Operator File..................................................................................................................5-3
5-2-1. Operator File Operation................................................................................................5-3
5-3. Preset Operator File...........................................................................................................5-4
5-3-1. Preset Operator File Operation.........................................................................................5-4
5-4. Scene File.....................................................................................................................5-5
5-4-1. Scene File Operation...................................................................................................5-5
5-5. Reference File.................................................................................................................5-7
5-5-1. Reference File Operation...............................................................................................5-7
5-6. Lens File.......................................................................................................................5-9
5-6-1. Lens File Operation.....................................................................................................5-9
HSC300RF/HSC100RF/HSC300R/HSC100R 3

5-7. OHB File.....................................................................................................................5-11
5-7-1. OHB File Operation...................................................................................................5-11
5-8. File Items.....................................................................................................................5-13
6. Setup Menu
6-1. Overview of Setup Menu......................................................................................................6-1
6-1-1. How to Display the SERVICE Menu/ How to Change the Setting Values............................................6-1
6-1-2. Settable Special Functions..............................................................................................6-1
6-2. SERVICE Menu...............................................................................................................6-3
6-2-1. SERVICE Menu List...................................................................................................6-3
6-2-2. Description of SERVICE Menu........................................................................................6-3
7. Spare Parts
7-1. Note on Repair Parts..........................................................................................................7-1
7-2. Exploded Views...............................................................................................................7-2
7-3. Supplied Accessories........................................................................................................7-22
8. Diagrams
Block Diagrams.........................................................................................................................8-1
Frame Wiring...........................................................................................................................8-6
HSC300RF/HSC100RF/HSC300R/HSC100R 4

Manual Structure
Purpose of this manual
This manual describes the information items that premise the service based on the block-level such as service overview,
replacement of main parts, electrical alignment, file system, and setup menu assuming use of system and service
engineers.
Related manuals
The following manual is provided for this unit in addition to this “Service Manual”.
• Operation Guide (Supplied with this unit)
• Operation Manual CD-ROM (Supplied with this unit)
This manual contains information required to operate and use the unit.
• Factory Service Manual (Available on request)
Parts list, circuit diagram, and board layouts of the unit are included to provide information required for part-level
service.
Trademarks
Trademarks and registered trademarks used in this manual are follows.
• FRAM is a registered trademark of Ramtron International Corporation.
Other system names and product names written in this manual are usually registered trademarks or trademarks of
respective development manufacturers.
HSC300RF/HSC100RF/HSC300R/HSC100R 5

Section 1
Service Overview
1-1. Connectors and Cables
1-1-1. Connector Input/Output Signals
6
7
10
11
17
12
9
8
3
4
5
14
13
15
1: HSC300RF/100RF
2: HSC300R/100R
16
18
Input/Output Signals
1. CCU (HSC300RF/100RF)
BTA S-004A/005A/006A compliant,
1.4835 Gbps Serial
UC, CED: LEMO optical fiber connector
J, E: Tajimi optical fiber connector
2. CCU (HSC300R/100R)
UC: King triax connector
J: Tajimi triax connector
CED: Fischer triax connector, LEMO triax connector
3. PROMPTER/GENLOCK/RET
BNC type 75 Ω, 1.0 V p-p
4. TEST OUT
BNC type 75 Ω, 1.0 V p-p
5. SDI
HD SDI signal
BTA-S004 compliant
HSC300RF/HSC100RF/HSC300R/HSC100R 1-1

BNC type 75 Ω, 0.8 Vp-p
6. EARPHONE
Earphone φ3.5 mm stereo mini jack
7. INTERCOM
- External View -
1
2
5
43
XLR 5-pin, Female
(0 dBu = 0.775 V rms)
No. Signal I/O Specifications
1 Intercom MIC
(Y)
IN • Carbon micro-
phone: -20 dBu,
unbalance
• Dynamic micro-
phone: -60 dBu,
balance/unbalance
• Manual:
-20/-40/-60 dBu,
balance/unbal-
ance)
2 Intercom MIC
(X)
IN
3 GND — GND
4 Intercom Left OUT 11 dBu (VR max, 250
Ω load)
5 Intercom Right OUT
8. REMOTE
17
6
5
4
3
2
8
- External View -
8-pin, Female
No. Signal I/O Specifications
1 • TX (X): for
RCP
• TX1 (+): for
TRUNK
(RS-422A)
OUT • SERIAL DA-
TA OUT: for
RCP
• TRUNK DATA
OUT: for
RS-422A
2 • TX (Y): for
RCP
• TX1 (–): for
TRUNK
(RS-422A)
OUT
Continued
No. Signal I/O Specifications
3 • RX (X): for
RCP
• RX1 (+): for
TRUNK
(RS-422A)
IN • SERIAL DA-
TA IN: for RCP
• TRUNK DATA
IN: for
RS-422A
4 • RX (Y): for
RCP
• RX1 (–): for
TRUNK
(RS-422A)
IN
5 TX-GND — GND for TX
6 UNREG-OUT OUT UNREG +10.5 V to
+17 V dc, 200 mA
(max)
7 UNREG-GND — GND for UNREG-
OUT
8 RCP-PIX: for RCP OUT 75 Ω, 1.0 V p-p (SD
Video)
CHASSIS GND:
for TRUNK
(RS-422A)
— CHASSIS GND
9. RET CTRL
6-pin, Female
- External View -
34
16
25
No
.
Signal I/O Specifications
1 INCOM MIC-
ON/OFF: for
UC, J
ENG: for
CED, E
IN Zi ≧ 10 KΩ
ON: GND
OFF: OPEN
2 NC: for UC, J
PROD: for
CED, E
IN • UC, J: No connection
• CED, E: Zi ≧ 10 KΩ
ON: GND
OFF: OPEN
3 GND — —
4 RET 3-
ON/OFF
IN Zi ≧ 10 KΩ
ON: GND
OFF: OPEN
5 RET 1-
ON/OFF
IN
6 RET 2-
ON/OFF
IN
HSC300RF/HSC100RF/HSC300R/HSC100R 1-2

10. TRACKER
81
54
10 9 27
63
- External View -
10-pin, Female
No. Signal I/O Specifications
1 TRACKER
LEFT
OUT TRACKER RE-
CEIVE/
PGM –20 dBu unbal-
anced
2 GND (TALK) — GND for TRACKER
TALK
3 GND (RECEIVE/
PGM/TALLY)
— GND for
RECEIVE/PGM/
TALLY
4 TRACKER
RIGHT
OUT TRACKER RE-
CEIVE/
PGM –20 dBu unbal-
anced
5 UNREG OUT +12 V (+10.5 to +17.0
V)
6 GND (UNREG) — GND for UNREG
7 TRACKER
TALK (X)
IN TRACKER TALK 0
dBu/
–20 dBu, High impe-
dance balanced
8 TRACKER
TALK (Y)
IN
9 G TALLY OUT ON: GND
OFF: High impe-
dance (Open collec-
tor)
10 R TALLY OUT ON: GND
OFF: High impe-
dance (Open collec-
tor)
11. DC OUT
1
23
4
- External View -
4-pin, Female
No. Signal I/O Specifications
1 UNREG GND — GND for UNREG-OUT
2 NC — No connection
3 NC — No connection
4 UNREG OUT +10.5 to 17 V dc, 500 mA
(max)
12. DC IN
1
23
4
- External View -
XLR 4-pin, Male
No. Signal I/O Specifications
1 EXT_DC (C) — GND for DC (+)
2 NC — No connection
3 NC — No connection
4 EXT_DC (H) IN +10.5 V to 17 V dc
13. AUDIO IN CH1/CH2
1
2
3
- External View -
(0 dBu = 0.775 Vrms)
XLR 3-pin, Female
No. Signal I/O Specifications
1 AUDIO
CH1/CH2 (G)
— –60 dBu, –50 dBu,
–40 dBu, –30 dBu,
–20 dBu, LINE (0 dBu)
selectable, balanced
2 AUDIO
CH1/CH2 (X)
IN
3 AUDIO
CH1/CH2 (Y)
IN
14. FRONT MIC
1
2
3
- External View -
(0 dBu = 0.775 Vrms)
XLR 3-pin, Female
No. Signal I/O Specifications
1 MIC 1 (G) — –60 dBu, –50 dBu,
–40 dBu, –30 dBu,
–20 dBu selectable, bal-
anced
2 MIC 1 (X) IN
3 MIC 1 (Y) IN
HSC300RF/HSC100RF/HSC300R/HSC100R 1-3

15. VF
- External View -
20-pin, Female
No. Signal I/O Specifications
1 S-DATA IN/
OUT
TTL level
2 NC — No connection
3 NC — No connection
4 SCK OUT TTL level
5 NC — No connection
6 NC — No connection
7 NC — No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC — No connection
10 NC — No connection
11 NC — No connection
12 Y VIDEO OUT 1.0 V p-p,
Zo = 75 Ω
13 VIDEO GND — GND for VIDEO
14 Pb VIDEO OUT ±0.35 V p-p,
Zo = 75 Ω
15 Pr VIDEO OUT ±0.35 V p-p,
Zo = 75 Ω
16 NC — No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC — No connection
19 UNREG GND — GND for UNREG
20 UNREG OUT +10.5 V to +17 V
16. LENS
- External View -
12-pin, Female
12 11
46
73
28
91
10
5
No. Signal I/O Specifications
1 RET VIDEO
ENABLE
IN • ENABLE: 0 V
• DISABLE: +5 V or
OPEN
Continued
No. Signal I/O Specifications
2 VTR CTL IN • ENABLE: 0 V
• DISABLE: +5 V or
OPEN
3 GND — GND for UNREG
4 SERVO
MA/AT
OUT • AUTO: +5 V
• MANU: 0 V or
OPEN
5 IRIS POSI-
TION
OUT +3.4 V (F16) to +6.2 V
(F2.8)
6 UNREG OUT +10.5 V to +17 V
7 IRIS POSI-
TION
IN +3.4 V (F16) to +6.2 V
(F2.8)
8 IRIS AT/MA OUT • AUTO IRIS: 0 V
• MANUAL IRIS:
+5 V
9 EXTENDER
ON/OFF
IN • EX 2 ON: GND
• EX 0.8 ON: 30 kΩ
to GND
• OFF: OPEN
30 kΩ
EX 2 ON
EX 0.8 ON
10 ZOOM POSI-
TION
IN • WIDE: 2 V
• TELE: 7 V
11 FOCUS POSI
(LENS RX)
IN • ∞: 7 V
• min.: 2 V
12 FOCUS POSI
(LENS TX)
OUT —
17. USB
USB (Series A), 4-pin
Signal standard: USB standard Ver. 2.0
- External View -
14
No. Signal I/O Specifications
1 VBUS OUT USB Vcc (+5 V)
2 D+ IN/
OUT
USB+
3 D– IN/
OUT
USB–
4 GND — GND
18. DC OUT
- External View -
2-pin, Female
12
HSC300RF/HSC100RF/HSC300R/HSC100R 1-4

No
.
Signal I/O Specifications
1 LIGHT +12 V OUT +12 V dc, 2.5 A (max)
2 GND — GND for power
1-1-2. Wiring Diagrams for Cables
CCA-5 Cable (for REMOTE connector)
BrownBrown
Brown
Red
Red
White
White
White
Orange
Black
— 8P CONNECTOR (MALE) —
(WIRING SIDE)
INTERCOM MIC Cable
1. Balance (HEAD SET menu UNBAL: OFF)
G
XINTERCOM
MIC
Y
2. Unbalance (HEAD SET menu UNBAL: ON)
XINTERCOM
MIC
Y
1-1-3. Connection Connectors/Cables
Connection made with the connector panels during installation or
service, should be made with the connectors/complete cable
assemblies specified in the following list, or equivalent parts.
Connector Name Connector/Cable
CCU: HSC300R/
100R
• Fujikura φ8.5 mm
• Fujikura φ14.5 mm
• Belden 9232 φ13.2 mm
• TEST OUT
• PROMPTER/
GENLOCK/RE
T
• SDI
(BNC type)
Plug, BNC (Part No.: 1-569-370-12) or 5C-
FB coaxial cable/ Recommendation made by
Fujikura
• AUDIO IN
CH1/CH2
• FRONT MIC
(XLR type 3-
pin, Female)
XLR, 3-Pin Male (Part No.: 1-508-084-00)
or ITT Cannon XLR-3-12C or equivalent
RET CTRL
(6-pin, Female)
Plug, 6-Pin Male (Part No.: 1-560-078-00)
or HIROSE HR10-7PA-6P or equivalent
DC OUT
(4-pin, Female)
Plug, 4-Pin Male (Part No.: 1-566-425-11)
or HIROSE HR10A-7P-4P or equivalent
DC OUT
(2-pin, Female)
Power tap (OE) ANTONBAUER 33710 or
equivalent
INTERCOM
(XLR type 5-pin, Fe-
male)
XLR, 5-Pin Male (Part No.: 1-508-370-11)
or ITT Cannon XLR-5-12C or equivalent
DC IN
(XLR type 4-pin,
Male)
XLR, 4-Pin Female (Part No.:
1-508-362-00) or ITT Cannon XLR-4-11C
or equivalent, or Cable assembly (Part No.:
1-551-577-00) (supplied with AC-550)
REMOTE
(8-pin, Female)
• Plug, 8-Pin Male (Part No.:
1-766-848-11) or CCA-5 cable assem-
bly (CCA-5-10 (10 m) /CCA-5-3 (3
m)) (optional)*1*2
• REMOTE cable (Part No.:
1-783-372-11) (supplied with
RMB-170, 10 m)*1*2*3
TRACKER
(10-pin, Female)
Connector, Round Type 10-Pin (Part No.:
1-506-522-12) or HIROSE
HR10A-10P-10P or equivalent
1-1-4. Note in Connecting CCU Connector
Tip
This section is required for HSC300RF/100RF. This section is not
required for HSC300R/100R.
*1: If using a cable of length different from a standard product, contact your local Sony Sales Office/Service Center.
*2: The pin 8 of CCA-5 cable is GND (ground). The pin 8 of REMOTE cable is not GND (ground).
*3: Use of REMOTE cable enables to monitor video signals. (The pin 8 is available for the video signal line.) The down-converted SD
signal is output.
HSC300RF/HSC100RF/HSC300R/HSC100R 1-5

It is recommendable to clean the optical contact portions
mentioned below before connecting this unit to the camera control
unit.
• CCU connector of this unit
• CAMERA connector of the camera control unit
• Optical/Electrical cable
For details on a cleaning method, refer to “1-7. Cleaning of
Connector/Cable”.
HSC300RF/HSC100RF/HSC300R/HSC100R 1-6

1-2. Location of Printed Circuit Boards
PA-418
TG-285 DR-675
PA-418
TG-285 DR-675
SE-1138
(HSC100RF/100R)(HSC300RF/300R)
Filter disk servo
board
AT-189E
SW-1607
CN-3640
SY-430
SW-1609
CN-3642
PS-879
DPR-358
RE-319
MB-1207
CN-3638
CN-3637
SW-1606
HSC300RF/HSC100RF/HSC300R/HSC100R 1-7

CN-3639
SW-1608: UC, J
SW-1608A: CED, E
CN-3645
CN-3647
CN-3643
CN-3648
CN-3641
CN-3653
SDI-117
CN-3644
CN-3646
LE-392
SW-1605
SW-1604
(HSC300RF/100RF)
CN-3645
CN-3647
CN-3643
CN-3648
CN-3641
FL-377
CD-78
CN-3644
CN-3646
LE-392
SW-1605
CN-3639
TX-148
SW-1604
(HSC300R/100R)
SW-1608: UC, J
SW-1608A: CED, E
HSC300RF/HSC100RF/HSC300R/HSC100R 1-8