Sony SuperHAD CCD II SSC-FB537 User manual

English
Before operating the unit, please read this manual thoroughly and retain it for
future reference.
WARNING
To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquid, such as vases, shall be placed on the apparatus.
WARNING
The mains plug must be used to disconnect mains power.
Please ensure that the socket outlet is installed near the equipment and shall be
easily accessible.
WARNING
This installation should be made by a qualified service person and should
conform to all local codes.
ATTENTION
The electromagnetic fields at the specific frequencies may influence the picture
of this unit.
IMPORTANT
The nameplate is located on the top.
Features
The SSC-FB537/FB567 color video camera is equipped with the
1/3 type Super HAD CCD IITM*and also has the following features:
High resolution and high sensitivity

Wide dynamic range using DynaViewSX technology

Noise Reduction

Day/Night function allowing color/monochrome mode switching

Alarm output using the Motion Detection Function (SSC-FB567 only)

AC 220 V - 240 V power supply system

Line lock function for synchronizing through AC power source

Easy setup using on-screen menu by English and Chinese language

* Super HAD CCD IITM is a trademark of Sony Corporation.
Notes on Use
Power supply
The SSC-FB537/FB567 must always be operated with an AC 220 V - 240 V (50 Hz)
power supply.
Handling of the unit
Be careful not to spill water or other liquids on the unit, or allow combustible or
metallic objects to fall inside the body. If used with a foreign object inside, the
camera is liable to fail, or be a cause of fire or electric shock.
Operating or storage location
Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,
avoid operating or storing the camera in the following locations, as these can be
a cause of a malfunction:
Extremely hot or cold places (Operating temperature:–10°C to +50°C)

Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,

near heaters)
Close to sources of strong magnetism

Close to sources of powerful electromagnetic radiation, such as radios or TV

transmitters
Locations subject to vibration or shock

Humid or dusty locations

Locations exposed to rain

Locations under the influence of fluorescent light or reflection of a window

Under an unsteady light (the image will flicker)

Where it is subject to moisture

Where it is subject to fumes and oil stains

Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
When transporting the camera, repack it as originally packed at the factory or in
materials of equal quality.
Cleaning
Use a blower to remove dust from the lens.

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn

stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may

damage the surface finishes.
Other
When the BLC menu is set to an option other than OFF, “hunting” may occur,

that is, the image may get darker and lighter as the camera “hunts”for the
optimum exposure level. If hunting occurs, set the BLC menu to OFF.
If you use the CCD-IRIS function in locations where the camera is exposed to

fluorescent light, a slow color change may occur.
The focus may be less sharp under near infrared light than under visible light.

The best camera performance may not be obtained under near infrared light

due to the lens coating.
In the event of any problems with the operation of the camera, contact your
Sony dealer.
Note on laser beams
Laser beams may damage the CCDs. If you shoot a scene that includes a laser
beam, be careful not to let a laser beam become directed into the lens of the
camera.
Note
If you use the Line Lock function in an operating environment where power
quality is poor, the monitor image may be distorted.
Location and Function of Part
Top/Front/Side 
Lens mount
Use to mount an appropriate CS-mount lens.
Focal length adjustment
Use this screw to adjust the focal length (the distance between the lens
mounting plane and the image plane).
Lens connector (4-pin socket)
Supplies power and control signals to an auto-iris lens (not supplied).
Tripod screws
The screw holes for attaching the tripod are located on
both the top and bottom of the camera. Use a 1/4" 20
UNC screw to attach a tripod to the camera.
The tripod must be set up on a flat surface and
tightened firmly by hand.
Caution
Use the mounting screw whose length is 4.5 mm – 7 mm only. Use of other
screws may cause improper mounting and damage parts inside the camera.
PHASE adjustment screw
Use to adjust the vertical phase of cameras synchronized by Line Lock.
Rear 
MENU/ENTER button
Use for menu operation. Press this button to display the menu or confirm
settings.
Press the button towards or to move the cursor up or down. Press the
button towards or to change a menu setting.
For details on use, refer to the supplied "Menu Operations" manual.
I/O port (SSC-FB567 only)
Pin No. Signal Description
1REMOTE + for future system expansion using an RS-485
connection
2REMOTE – for future system expansion using an RS-485
connection
3ALARM OUT Outputs 5 V potential when Motion Detection is
enabled and triggered while outputs 0 V
normally.
4COM common to pins No. 3, 5 and 7
5EXTERNAL CTRL OUT H (+5 V) is output between this terminal and
COM when the color mode is selected; L (0 V) is
output when the B/W mode is selected.
6COM common to pins No. 3, 5 and 7
7EXTERNAL CTRL IN When H (+5 V) is applied between this terminal
and COM, the color mode is selected; when L
(0 V) is applied, B/W mode is selected.
Power inlet (AC 220 V - 240 V, 50 Hz)
Fall-prevention rope mounting hole
When installing the camera on a ceiling or wall, be sure to secure a fall-
prevention rope (not supplied) to this hole for safety.
VIDEO OUT (composite video signal output) connector (BNC type)
Installation
WARNING
If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.
If you install the camera on the ceiling, ensure that the ceiling is strong

enough to withstand the weight (20 Kg) of the camera plus the bracket and
then install the camera securely. If the ceiling is not strong enough, the
camera may fall and cause serious injury.
To prevent the camera from falling, make sure to attach the fall-prevention

rope (not supplied).
If you attach the camera to the ceiling, check periodically, at least once a

year, to ensure that the connection has not loosened. If conditions warrant,
make this periodic check more frequently.
Suitable lens 
The lens must be a CS-mount type of less than 1 kg. The protrusion behind the
mounting surface must be 4 mm or less.
中文
使用本机前，请仔细阅读本使用手册并妥善保存以备日后参考。
警告
为减少火灾或电击危险，请勿让本设备受到雨淋或
受潮。
为防止触电严禁拆开机壳，维修请咨询具备资格人
士。
设备不要受到滴水或水溅，不要将盛满液体的花瓶等物品放在设备
上。
警告
必须使用本设备的电源插头断开电源。
请确保电源插座安装在本设备附近且便于使用。
安装
警告
如果要将摄像机安装在墙壁或天花板等高处，请将安装工作委托
 给有经验的承包商或安装人员。
如果要将摄像机安装在天花板上，必须确保天花板有足够的强度
 承受摄像机加上支架的重量（总共20 Kg），然后再牢固安装摄
像机。如果天花板强度不够，则摄像机可能掉落并造成严重损
伤。
为了防止摄像机掉落，请务必安装防坠绳（非附带）。
 如果将摄像机安装在天花板上，请定期检查，每年至少一次，以
 确保连接没有松动。如果条件允许，请更频繁定期检查。
合适的镜头 
镜头必须是重量低于1 kg的CS型接口。接口面后方的突起部分必须
小于4 mm。
警告
本安装应该由有资格的服务人员进⾏，并须符合所有当地法规规
定。
警告
此为A级产品。在生活环境中，该产品可能会造成无线电干扰。
在这种情况下，可能需要用户对干扰采取切实可⾏的措施。
注意
特定频率的电磁场可能会干扰本机的图像。
重要
设备铭牌位于顶部。
关于旧产品的处理
请不要将旧的产品与一般的生活垃圾一同弃置。
正确弃置旧的产品有助于避免对环境和人类健康造成潜在的负面影响。
具体处理方法请遵循当地的规章制度。
特点
SSC-FB537/FB567彩色摄像机配备有1/3型Super HAD CCD IITM*并具有以
下特点：
高分辨率和高灵敏度
 采用DynaViewSX技术的宽动态范围
 降噪功能
 可切换彩色/黑白模式的白天/夜间功能
 使用动态检知功能进⾏报警输出（仅SSC-FB567）
 220 V-240 V交流供电系统
 交流电源同步的线路锁定功能
 利用中/英文菜单屏幕可轻松完成设定

* Super HAD CCD IITM是Sony Corporation的商标。
使用须知
电源
SSC-FB537/FB567必须始终在220 V-240 V（50 Hz）交流电源下才能
工作。
使用本机
请小心不要溅水或溅洒其他液体在本机上，或使易燃物或金属物掉
入机内。若在异物进入机内的状态下使用本机，摄像机可能会发生
故障或因此发生火灾或触电。
操作或存放场所
请勿拍摄非常亮的物体（灯光、阳光等）。避免在以下位置使用或
存放摄像机，否则会导致故障。
极热或极冷的地方（操作温度：-10℃至＋50℃）
 长时间暴露于直射阳光下，或者靠近热源（⽐如加热器）的地方
 靠近强磁源的位置
 靠近无线电或电视发射器等强电磁辐射源的地方
 易于受到强⼒振动或撞击的地方
 潮湿或有灰尘的地方
 暴露于⾬水的地方
 受到荧光灯或窗户反射光影响的地方
 在不稳定光线的下面（图像会闪烁）
 结露和高湿的环境
 油烟或油污的环境

通风
为了避免热量积蓄，不要阻挡摄像机附近的通风。
运送
当运送摄像机时，重新以出⼚时的包装进⾏包装，或用同等品质的
材质包装。
清洁
用吹灰器清除镜头灰尘。
 使用柔软、干燥的布清洁摄像机的外表面。要清除顽固的污渍，
 请用少量清洁剂蘸湿软布，然后擦干即可。
不要使用酒精、苯或稀释剂等挥发性溶剂，这些物质可能会破坏
 表面光洁度。
其他
当BLC菜单处于“OFF”以外的其他位置时，可能出现“猎
 振”。这是因为摄像机“猎振”以设定最佳曝光等级而可能使图
像变得忽明忽暗。遇此情况时，请将BLC菜单设定于“OFF”位
置。
若在摄像机暴露于荧光灯光线的场所使用CCD-IRIS功能，可能会
 发生缓慢的色彩变化。
在近处的红外线条件下，聚焦可能不如在可见光条件下清晰。
 因镜头涂层的原因，在近处的红外线条件下摄像机可能无法发挥
 其最佳性能。
有关在摄像机使用过程中出现的任何问题，请与您的Sony维修代理
联系。
有关激光束的注意事项
激光束可能会损伤CCD。如果拍摄包含激光束的场景，请注意不要
让激光束直接射入摄像机镜头。
注
如果在电源质量差的操作环境下使用线路锁定功能，监视器图像可
能失真。
部件的位置和功能
顶部/前面/侧面 
镜头接口
用于安装适当的CS型接口镜头。
焦距调节
使用此螺丝调节焦距（镜头安装板和图像板之间的距离）。
镜头插口（4针插座）
为自动光圈镜头（不提供）提供电源和控制信号。
三脚架螺丝孔
摄像机的顶部和底部都有用于安装三脚架的
螺丝孔。使用1/4" 20 UNC螺丝将三脚架
安装到摄像机上。三脚架必须放置在平坦的
表面上，并用手拧紧。
注意
只能使用长度为4.5 mm - 7 mm的安装螺丝。使用其它螺丝可能会
造成不当安装，并可能损坏摄像机内部零件。
PHASE调节螺丝
使用此螺丝可调节通过线路锁定同步的摄像机的垂直相位。
后面 
MENU/ENTER键
用于菜单操作。按此键可显示菜单或确认设定。
将按键朝着或按可将光标向上或向下移动。将按键朝着或按可
改变菜单设定。
有关使用的详情说明，请参阅附带的“菜单操作”手册。
I/O接口（仅SSC-FB567）
针号 信号 说明
1REMOTE＋ 用于将来采用RS-485连接方式进⾏系
统扩展
2REMOTE - 用于将来采用RS-485连接方式进⾏系
统扩展
3ALARM OUT 当动态检知功能启动并激活时，输出
5 V电压，通常状态为0 V电压。
4COM 共用针号为3、5和7。
5EXTERNAL
CTRL OUT
当选择了色彩模式时，此端子与COM之
间输出为H（＋5 V）；当选择了黑白
模式时，输出为L （0 V）
6COM 共用针号为3、5和7。
7EXTERNAL
CTRL IN
此端子和COM之间使用H（＋5 V）时，
彩色模式被选择；使用L （0 V）时，
黑白模式被选择
电源插座（交流220V-240V，50Hz）
防坠绳安装孔
当将摄像机安装到天花板或墙上时，请务必将防坠绳（非附带）固
定到此孔中以确保安全。
VIDEOOUT（复合视频信号输出）连接器（BNC型）
4-430-506-01(1)
© 2012 Sony Corporation Printed in China
Color Video Camera
彩色摄像机
SSC-FB537/FB567
Operating Instructions
使用手册
A
ADJUST
LENS
ɠɡ ɞɟ
ɢ
B
ɦɥ ɧ
ɣ
ɦɥ ɧ
ɣ ɤ
SSC-FB537 SSC-FB567
C
CS-mount lens/CS接口镜头
4 mm or less/
4 mm以下
1/4”, 20 UNC
= 4.5 mm – 7 mm
(ISO standard) (with the
screws fastened)
1/4”,20UNC
=4.5mm-7mm（ISO
标准）（用螺丝固定）

D
3
1
2
4
Rib/隔片
Lens Connector (not supplied)/镜头插头（不提供）
[English]
Rib (If the cable is thick, cut this off.)
Pin 1 DC control Control –
Pin 2 DC control Control +
Pin 3 DC control Drive +
Pin 4 DC control Drive – (Ground)
[中文]
隔片（如果电缆太粗，则将此隔片切除。）
针 1 DC控制 控制-
针 2 DC控制 控制＋
针 3 DC控制 驱动＋
针 4 DC控制 驱动-（接地）
E
ADJUST
LENS
F
ADJUST
LENS
Fall-prevention
rope (not supplied)/
防坠绳（非附带）
1
2
G
ʓ ʖ
ʔ
ʕ
SSC-FB567
SSC-FB537
ʓ ʖ
ʔ
ʕ
Connecting the Camera 
Connect the video cable to the VIDEO OUT connector.
Connect the video cable to the VIDEO IN connector of a video monitor, etc.
Connect to the appropriate power source using a power cable.
To an AC 220 V - 240 V (50 Hz) power source.
75-ohm coaxial cable.
Notes
Be sure to input only the proper voltage to the power terminal of the

camera.
Be sure to push the power cable all the way in.

Phase Adjustment
If the picture roll vertically, adjust the vertical phase using V PHASE adjustment
screw.
Typical CCD phenomenon
The following phenomena that may appear in images are specific to CCD
(Charge Coupled Device) image sensors. They do not indicate malfunctions.
White flecks
Although the CCD image sensors are produced with high-precision technologies,
fine white flecks may be generated on the screen in rare cases, caused by cosmic
rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
- when operating at a high environmental temperature
- when you have raised the gain (sensitivity)
- when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or flashlight, is being
shot, vertical tails may be produced on the screen, or the image may be
distorted.
Monitor screen Vertical tails shown on the image
Bright object (e.g., strong spotlight, strong
reflected light, flashlight, the sun)
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
Specifications
Image device Interline transfer 1/3 type
Effective picture elements 976 (H) x 582 (V)
Lens mount CS-mount
Signal system PAL color system
Synchronization system Internal / Line Lock
Horizontal resolution 650 TV lines (NORMAL mode)
Minimum illumination SSC-FB537:
Color: 0.08 lx at F1.2 (50IRE, AGC ON, Turbo mode)
Color: 0.05 lx at F1.2 (30IRE, AGC ON, Turbo mode)
B/W: 0.05 lx at F1.2 (50IRE, AGC ON, Turbo mode)
B/W: 0.03 lx at F1.2 (30IRE, AGC ON, Turbo mode)
SSC-FB567:
Color: 0.08 lx at F1.2 (50IRE, AGC ON, Turbo mode)
Color: 0.05 lx at F1.2 (30IRE, AGC ON, Turbo mode)
B/W: 0.01 lx at F1.2 (50IRE, AGC ON, Turbo mode)
B/W: 0.006 lx at F1.2 (30IRE, AGC ON, Turbo mode)
Video output 1 Vp-p, 75 ohms, negative sync
Video S/N 55 dB (AGC OFF, WEIGHT ON)
Dynamic range 75 dB typical
Electronic shutter 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000, 1/20000, 1/40000, 1/80000, 1/100000 (sec)
White balance ATW-PRO/ATW/3200K/5600K/MANUAL
Automatic gain control
(AGC)
OFF/NORMAL/TURBO/MANUAL
Power supply AC 220 V - 240 V (50 Hz)
Power consumption SSC-FB537: 2.0 W
SSC-FB567: 2.4 W
Operating temperature – 10 °C to +50 °C
Operating humidity 20% to 80%
Storage temperature – 40 °C to +60 °C
Storage humidity 20% to 95%
Mass SSC-FB537: Approx. 240 g
SSC-FB567: Approx. 250 g
Dimensions 63 × 57 × 124 mm (not including projecting parts)
(w/h/d)
Supplied accessories Lens mount cap (1)
Menu operations (1)
Power cable (1)
Operating Instructions (this document) (1)
Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
Regular parts replacement
Some of the parts that make up this product (electrolytic condenser, for
example) need replacing regularly depending on their life expectancies. The
lives of parts differ according to the environment or condition in which this
product is used and the length of time it is used, so we recommend regular
checks.
Consult the dealer from whom you bought it for details.
中文
自动光圈镜头插头的安装 
使用自动光圈镜头时，请安装镜头插头（不提供）。
此安装只可由专业维修人员或系统安装人员来执⾏。本摄像机包装
中未附带镜头插头。
1 切去镜头插头边缘的光圈控制电缆，以取下现有的镜头插头，然
后如图所示除去电缆外套。
2 将镜头电缆焊接到镜头插头的针脚上。
安装镜头 
1 卸下镜头接口盖。
2 旋进镜头并拧紧，直至牢固。
3 将镜头插头插入LENS插座。
安装手动光圈镜头时可省略步骤3。
4 根据镜头类型，旋转焦距调节螺丝调节焦距。
注意
当摄像机上未安装镜头时，请始终将镜头安装盖放在摄像机上。
 检查镜头卡座

每年至少检查1次镜头卡座以确保其未出现松动。如果条件允
许，请更频繁定期检查。
安装摄像机
注意
将摄像机安装在天花板或较高位置时，确保将防坠绳（未附带）固
定到摄像机以确保安全。
注意
若将摄像机安装在天花板上，务必请悬挂牢实，否则摄像机会落下
造成伤害。
若用悬架、机架和联动旋转底座（盘/架）等装置将摄像机安装在天
花板上，请进⾏以下操作：
使用三脚架螺丝并用起子拧紧它们。请向附近的Sony经销店订购
 三脚架螺丝（Sony零部件号：3-174-693-02）。
请在平坦处安装三脚架连接器。

安装防坠绳 
当将摄像机安装到天花板或较高位置时，请务必安装防坠绳
（非附带）以防止摄像机掉落。
将防坠绳穿过摄像机背面的孔中，然后用螺丝（不提供）将其固定
到天花板或墙壁上的接线盒，如图所示。
有关防坠绳的详细说明，请咨询购买产品所在商店，或Sony的授权
经销商。
注
请使用符合接线盒（不提供）螺丝孔的螺丝。
连接摄像机 
 将视频电缆连接到VIDEO OUT接口。
 将视频电缆连接到视频监视器等设备的VIDEO IN接口。
 使用电源线连接合适的电源。
连接220 V-240 V（50Hz)交流电源
 75 Ω同轴电缆。
注
请务必只可将正确的电压输入到摄像机的电源端口。
 请务必将电源线完全推入。

相位调节
如果图像可能垂直滚动，请使用PHASE调节螺丝调节垂直相位。
典型CCD现象
图像中可能出现的以下现象是CCD（电荷耦合器件）图像传感器所特
有的。这些现象不是故障。
白斑
虽然CCD图像传感器是采用高精度技术生产的，但由于宇宙射线等的
影响，其屏幕上可能会出现细小的白斑（极少数情况）。
这与CCD图像传感器的原理有关，出现的白斑并不是故障。
在以下情况中，⽐较容易出现白斑：
- 在高温环境下进⾏操作时
- 提高倍率（灵敏度）时
- 当使用慢快门时
垂直拖影
拍摄亮度极高的物体（如强聚光灯或闪光灯）时，屏幕上可能出现
垂直尾线，图像也可能出现扭曲。
监视器屏幕 图像上显示的垂直拖尾
高亮物体（如强聚光灯、强反射光、闪光灯、
阳光）
图形失真
拍摄微小的图案、条纹或线条时，它们可能呈锯齿状或出现闪烁现
象。
规格
成像器件 ⾏间转移1/3型
有效像素 976 (H) × 582 (V)
镜头安装 CS型接口
信号制式 PAL彩色制式
同步系统 内部/线路锁定
水平分辨率 650电视线（NORMAL模式）
最低照度 SSC-FB537：
彩色： 0.08 lx于F1.2 （50IRE，AGC打开，加
强模式）
彩色： 0.05 lx于F1.2 （30IRE，AGC打开，加
强模式）
黑白： 0.05 lx于F1.2 （50IRE，AGC打开，加
强模式）
黑白： 0.03 lx于F1.2 （30IRE，AGC打开，加
强模式）
SSC-FB567：
彩色： 0.08 lx于F1.2 （50IRE，AGC打开，加
强模式）
彩色： 0.05 lx于F1.2 （30IRE，AGC打开，加
强模式）
黑白： 0.01 lx于F1.2 （50IRE，AGC打开，加
强模式）
黑白： 0.006 lx于F1.2 （30IRE，AGC打开，
加强模式）
视频输出 1 Vp-p，75 Ω，负同步
视频S/N 55 dB（AGC关闭, WEIGHT打开）
动态范围 75 dB典型
电子快门 1/50, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10000, 1/20000,
1/40000, 1/80000, 1/100000(秒)
白平衡 ATW-PRO/ATW/3200K/5600K/MANUAL
自动增益控制（AGC）OFF/NORMAL/TURBO/MANUAL
电源 220 V-240 V（50 Hz）交流电源
功率消耗 SSC-FB537: 2.0 W
SSC-FB567: 2.4 W
操作温度 -10℃至＋50℃
操作湿度 20%至80%
储藏温度 -40℃至＋60℃
储藏湿度 20%至95%
重量 SSC-FB537:约240 g
SSC-FB567:约250 g
体积 63 × 57 × 124 mm（不包含突起）
（宽/高/长）
附件 镜头接口盖（1）
菜单操作手册（1）
电源线（1）
使用手册（本文档）（1）
设计和规格若有变更，恕不另⾏通知。
注意
在使用前请始终确认本机运⾏正常。
无论保修期内外或基于任何理由，SONY对任何损坏概不负责。由于
本机故障造成的现有损失或预期利润损失，不作
（包括但不限于）退货或赔偿。
定期部件更换
视其使用寿命而定，本产品中的某些部件（如电解质电容）需要定
期更换。部件的寿命因本产品的使用环境或条件以及使用的时间长
度而异，因此我们建议您定期进⾏检查。
详情请咨询向您销售本产品的经销商。
产品中有毒有害物质或元素的名称及含量 
使用环境条件：参考使用手册中的操作条件
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
实装基板 × ○ ○ ○ ○ ○
外壳 × ○ ○ ○ ○ ○
光学组件 × ○ ○ ○ ○ ○
附属品 × ○ ○ ○ ○ ○
○： 表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T11363-2006标准规定的限量要求以下。
×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超
出SJ/T11363-2006标准规定的限量要求。
4
1
3
2
English
Installation of an Auto Iris Lens Connector 
Install the lens connector (not supplied) when using an Auto Iris Lens.
This installation should be done only by qualified service personnel or system
installers. A lens connector is not included with this camera package.
1Cut the iris control cable at the edge of the lens connector to remove the
existing lens connector and then remove the outer cable cover as shown in
the illustration.
2Solder the lens cable to the pins of the lens connector.
Fitting the lens 
1Unscrew the lens mount cap.
2Screw in the lens, and turn it until it is secured.
3Insert the lens plug into the LENS connector.
When fitting a manual-iris lens, omit step 3.
4According to the type of lens, adjust the focal length by turning the focal
length adjustment screw.
Caution
Keep the lens mount cap on the camera when the lens is not installed yet.

Check the lens mount

Check the lens mount at least once a year to ensure it has not become loose.
If conditions warrant, make this periodic check more frequently.
Installing the Camera
Caution
When installing the camera on a ceiling or a high location, be sure to secure a
fall-prevention rope (not supplied) to the camera for safety.
ATTENTION
When installing the camera onto the ceiling, be sure it is secure. If not securely
installed, the camera may fall and injury may occur.
If the camera is installed on the ceiling using equipment such as a bracket,
housing and motored swivel base (pan/tilt), do the following:
Use tripod screws and securely tighten them with a driver. Order the tripod

screws (Sony Part No. 3-174-693-02) from your nearest Sony dealer.
Install the tripod adapter on a flat surface.

Attaching the fall-prevention rope 
When you install the camera on a ceiling or a high position, be sure to attach the
fall-prevention rope (not supplied) to prevent the camera from falling off.
Thread the fall-prevention rope through the hole on the rear of the camera, and
then fix it to the junction box on the ceiling or wall with a screw (not supplied),
as in the illustration.
For details about the fall-prevention rope, consult the store of purchase, or an
authorized Sony dealer.
Note
Use a screw to match the screw hole of your junction box (not supplied).
3