Sony CDP-C535 - Compact Disc Player User manual

SONY.
Compact Disc
Player
Operating Instructions
misi
CDP-C535
CDP-C435
© 1993 by Sony Corporation

Warning
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
OT NCRETO)N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIOE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a tisk of electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
~ Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
Owner’s Record
The mode! and serial numbers are located at the rear.
Record the serial number in the space provided below. Refer
to these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. Serial No.
For the Customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
POLARIZED AC PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
THIS APPARATUS COMPLIES WITH THE CLASS B LIMITS
FOR RADIO NOISE EMISSIONS SET OUT IN RADIO
INTERFERENCE REGULATIONS.
For the Customers in Australia
The following caution label is located inside of the unit.
DANGER
RADIATION DE LESER
INVISIBLE LORS D'OUVERTURE
AVEC L'ENCLENCHEMENT DE
SECURITE ANNULE EVITER
DERECT EXPOSURE TO | L'EXPOSITION DIRECTE AU
BEAM. RAYON. * T
This appliance is classified
as a CLASS 1 LASER
product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CLASS 1 LASER PROOUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT

Table of Contents
Precautions
Chapter 1 Introduction
PLOCAURIONS 5 snesena aA E 3
Chapter 2 Getting Started
UIMDACKING PPP AEE A ET 4
Hooking Up the System ......RRe...................................i. 5
Identifying ine aiiis 6
Chapter 3 Basic Operation
Playing Discs — Continuous Play ...................................... 8
Playing From the First Selection ..................R.....i.. 8
Information Display ................................................... 9
Locating a Particular Selection .................................. 10
Locating a Particular Point in a Selection ..................... 10
Replacing Discs While Playing a Disc .................... 11
Playing With Sound Effect
- Digital Signal Processing (CDP-C535 only)............004. 12
Fade-In/Fade-Out ............sessvsvssossrsorscssssossvssrsoesssosssssnseess 14
Playing in a Random Order — Shuffle Play ....................... 15
Playing in a Specified Order — Program Play .................. 16
Playing the Beginning of Each Selection
— Music Scan Play ...........sscsssssscsscrsssesscrsssorsrerssssesoes 19
Playing Repeatedly — Repeat Play .................................. 20
Chapter 4 Advanced Operation
Locating the Loudest Portion of the Disc - Peak Search ... 21
Specifying the Total Playing Time — Time Edit................... 22
Fading Out at the Desired Time — Time Fade ................006 24
Custom f 25
Storing Selections You Want to Play — Delete Bank .......... 26
Storing an Optimum Playback Level for Each Disc
bevelieeeee 28
Memorizing a DSP mode - DSP File
(CDP-C535 only) ...e..sessssosssossssossossssssassrosessesossssosssesssseso 29
Chapter 5 Additional Information
Maintenance .............ccccsccssscsescsvsccessersseserreccnessessssesereeses 30
Specifications ................................................................. 30
Toublsshooi9iggg, 31
Note when moving the player
Before moving the player, follow the procedure below to
return the internal mechanisms back to their original position.
1 Remove all of the discs from the disc tray.
2 Press the & OPEN/CLOSE button to close the disc tray.
Make sure that the “no disc” indication lights up in the front
panel display.
3 Wait for 10 seconds, then press the POWER button to turn
the player off.
Differences by Model
This instruction manual covers CDP-C535 and CDP-C435.
Their performance is identical except for the following:
e The CDP-C535 has the DSP and DSP File function.
¢ The CDP-C535 comes with the remote commander
RM-D535. The CDP-C435 comes with the RM-D435.
e The illustrations in this manual are of the CDP-C535.
Convention
JA This indicates a function operated only from the
T main unit.
On safety
¢ Should any solid or liquid object enter the cabinet, unplug
the unit and have it checked by qualified personne! before
operating it any further.
¢ Unplug the unit from the wall outlet if it is not to be used for
an extended period of time. To disconnect the cord, pull it
out by the plug. Never pull the cord itself. The unit is not
disconnected from the AC power source (mains) as long as
it is connected to the wall outlet, even if the unit itself has
been turned off.
* The AC power cord must be changed only at the qualified
service shop.
¢ As the laser beam used in this unit is harmful to the eyes,
do not attempt to disassemble the cabinet. Refer servicing
to qualified personnel only.
On operation
e Do not turn up the volume while listening to a portion with
no audio signals or very low level inputs. If you do, the
speakers may be damaged when a peak level portion is
played.
On the disc tray
e If the disc tray does not close properly and slides out again,
reinsert the discs.
¢ Be careful not to pinch your fingers between the disc tray
and the unit.
* Place only one disc in a disc compartment at a time.
e When the disc tray is open, do not press down on it forcibly,
nor place a heavy object on it.
On moisture condensation
If the unit is brought directly from a cold to a warm location,
or is placed in a very damp room, moisture may condense on
the lens inside the unit. Should this occur, the unit will not
operate. In this case, remove the disc and leave the unit
turned on for about an hour until the moisture evaporates.
Notes on handling discs
e To keep a disc clean, handle the disc by its edge.
Do not touch the surface.
e Do not stick paper or tape on the disc.
©
¢ Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, or leave it in a car parked in direct
sunlight as the heat may cause the disc to warp.
¢ After playing, store the disc in its case.
If you have any questions or problems concerning your
player, please contact your nearest Sony dealer.
For the Customers in the U.S.A.
For detailed safety precautions, see the leaflet “IMPORTANT
SAFEGUARDS’.

Chapter 2 Getting Started
Unpacking
Choosing a Good Location
e Place the player in a location with adequate air circulation
to prevent internal heat built up in the player.
e Do not place the player on a soft surface, such as a rug
that would block the ventilation holes on the bottom.
e Do not install the player:
— near heat sources such as radiators or air ducts.
- in a place subject to direct sunlight, excessive dust,
mechanical vibration or shock.
Inserting Batteries into the Remote
Commander
1 Slide open the cover.
Checking the Supplied Accessories
Make sure that all the supplied accessories are included with
your player. This manual and the following items are
included with your CDP-C535/CDP-C435.
2 Insert two size AA (R6)
batteries with
correct polarity.
Remote commander Sony batteries
RM-D535 (1) (CDP-C535) SUM-3(NS) (2)
RM-D435 (1) (CDP-C435)
Battery life
e About half a year of normal operation can be expected
when using the Sony batteries SUM-3(NS).
+ When the batteries are run down, the remote commander
will not operate the player. In this case, replace both
batteries with new ones.
Notes on remote commander operation
e Avoid exposing the remote sensor to direct sunlight or a lighting
apparatus. Such exposure may cause a malfunction.
e To avoid damage caused by battery leakage and corrosion. remove the
batteries when the commander will not be used for a long time

Hooking Up the System
Notes on Connection
¢ Turn off the power to each unit before making connections.
Connect the AC power cord last.
¢ Be sure to insert the plugs firmly into the jacks. Loose
connections may cause hum or noise.
e Leave a little slack in the connecting cord to allow for
inadvertent shock or vibration.
e Cord plugs and jacks are color coded:
Red plugs and jacks are for the right channel (R) and white
ones for the left channel (L).
Connecting an Amplifier
FIXED LINE OUT Æ VARIABLE LINE OUT
to an AC outlet
Speaker system
Amplifier
to an AC outlet
When using the LINE OUT
There are two ways of connecting with LINE OUT as follows:
FIXED: The output level is fixed.
VARIABLE: The output level can be adjusted with the LINE OUT/
PHONE LEVEL control (or with the LINE OUT LEVEL +/- buttons on
the remote commander.)
Notes on LINE OUT
e Connect your system to the VARIABLE output when using Level Files.
e if the LINE OUT/PHONE LEVEL control (or the LINE OUT LEVEL +/~
buttons on the remote commander) is adjusted while recording, the
recording level will change even when it is preset on the tape deck.

Front Panel
See the pages indicated in (__) for details.
Q] POWER switch (8)
[2] PLAY MODE buttons
CONTINUE button (8)
SHUFFLE button (15)
PROGRAM button (16)
DISC 1-5 buttons (8)
REPEAT button (20)
Remote sensor (4)
Display window (8)
7j Disc tray (8)
li (pause) button (8)
> (play) button (8)
84> 5 (AMS*) buttons (10)
</> (manual search) buttons (10)
E (stop) button (8)
DISC SKIP button (8)
14) & OPEN/CLOSE button (8)
DSP mode buttons and indicators (12) (CDP-C535 only)
HALL button
CHURCH button
JAZZ CLUB button
STADIUM button
DANCE button
3) 3] 23] 9] 3) 3] ||] S |)
6} i 18} [9] fig
DIRECT button (CDP-C535 only) (12)
DSP FILE button (CDP-C535 only) (29)
LEVEL FILE button (28)
FILE button (25)
ERASE button (25)
MUSIC SCAN button (19)
TIME button (9)
PEAK SEARCH button (21)
FADER button (14)
Numeric buttons (10)
>10 (over 10) button (10)
EDIT/TIME FADE button (22)
CLEAR button (16)
CHECK button (18)
PHONES jack (9)
LINE OUT/PHONE LEVEL control (9)
EX-CHANGE button (11)
RES PRSSREEREBSaas
* AMS is the abbreviation for Automatic Music Sensor.

Remote Commander
See
the
pages
indicated
in
¶)
for
details.
[1] PLAY MODE buttons
CONTINUE button (8)
SHUFFLE button (15)
PROGRAM button (16)
DISC 1-5 buttons (8)
CHECK button (18)
>20 (over 20) button (10)
REPEAT button (20)
TIME button (9)
il (pause) button (8)
> (play) button (8)
§<</>P1 (AMS) buttons (10)
<<>> (manual search) buttons (10)
a (stop) button (8)
DSP
SELECT
button
(CDP-C535
only)
(12)
MUSIC SCAN button (19)
DISC SKIP button (8)
Numeric buttons (10)
FILE button (25)
CLEAR button (16)
LEVEL FILE button (28)
ERASE button (25)
FADER button (14)
LINE OUT LEVEL +/- button (9)
DIRECT button (CDP-C535 only) (12)
NEEEEEREREREEEevee eels

Chapter 3 Basic Operation
Playing Discs — Continuous Play
In continuous play mode, you can play up to five discs consecutively.
Before playing discs, turn on the amplifier and set the input selector to the CD player
position. While playing a disc, you can replace the other four discs in the player with
new ones using the EX-CHANGE button.
Playing From the First Selection
4 Press DISC SKIP to set the next empty disc
compartment and place another disc in it.
LINE OUT/
PHONE LEVEL
1 Press POWER.
oopaon
atta
- i CC) keko
The display lights up.
Each time you press CONTINUE, the indication ALL
DISCS and 1 DISC alterate in the display.
Press ® or DISC 1-5.
Disc number
Disc compartment
woo
Č
3 Place a disc with the labe) side up
in the disc compartment.
The disc tray closes to start playing the first
selection.
— If you press >, the disc in the front
loading position starts playing.
— If you press one of the DISC 1-5 buttons,
the selected disc starts playing.
To stop play
To pause during play, press il.
~ To play more than one disc, go to step 4. Press P or il to resume play.
- To play only one disc, go to step 5. To stop play, press @.
To stop play and open the tray, press &.

To select the disc from which the playing starts
There are two ways.
a) To scan discs, press or hold down DISC SKIP.
b) To select a particular disc directly, press the
corresponding DISC 1-5 button.
Notes on ALL DISCS and 1 DISC
e If you choose ALL DISCS, all the discs in the player are piayed
consecutively. An empty disc compartment is skipped.
e Ifyou choose 1 DISC, only one disc is played.
Notes on disc tray
e Place a disc in the empty disc compartment only when it is in the front
loading position. Otherwise, the player may not be able to find the disc.
e Always close the disc tray when not using the player to prevent dust from
entering the unit.
e Place the disc properly in the disc compartment to prevent the disc from
being damaged.
When listening with headphones
Connect the headphones to the PHONES jack and adjust the
volume with the LINE OUT/PHONE LEVEL control on the
player (or with the LINE OUT LEVEL +/- buttons on the
remote commander).
To play an 8 cm (3-inch) CD
Place it in the inner circle in the disc compartment. If the disc
is provided with an adaptor, first remove it. Do not put a
normal CD (12cm/5-inch) on top of an 8 cm (3-inch) CD.
Information Display
Checking the total number of selections and total
playing time of the disc to be played.
There are two ways to check.
a) Place the disc in the disc compartment in the front loading _
position, then press & or the disc tray itself to close it.
b) Press TIME on the player during stop. To check another
disc, press DISC SKIP, then press TIME.
moss D 22 90E
ir 65.48 Come} CCE
Disc number Total number Total playing Music calendar
selected to of selections time of the
be played on the current disc
(current disc) current disc
Notes on “D 2)...” in the display
e The red circle around a disc number indicates the disc is ready to be
played.
The red circle moves each time you press DISC SKIP.
e When ail the selections on a disc have been played, the semi-circle around
the disc number disappears.
¢ When a compartment is recognized as empty, the semi-circled disc
number disappears.
Changing the display
Each time you press TIME during play, the display changes
to give you the following information:
Elapsed time in the selection
being played (current selection)
Current selection number
Remaining time in the current selection.
If the current selection number is
greater than 20, “- -.- -" appears
Total remaining time on the current
disc (does not appear in shuffle
or program mode)
Notes on the information display
e Total remaining time is only available in the continuous play mode.
e Total remaining time will appear if the time fade function is set during
program or shuffle play.
What is this indication?
aot teh ee ES
tht bbb otk
This indication appears when all disc compartments are empty.

Playing Discs
Locating a Particular Selection
There are two ways to locate the beginning of a desired
ene selection on the current disc.
A. To locate sequentially (Automatic Music Sensor)
— Press I< once to locate the beginning of the current
selection.
- Press PPI once to locate the beginning of the next
selection.
— Hold down I4< or PPI to skip selections.
B. To locate a selection directly
Press one of the numeric buttons on the player or remote
commander to enter the desired selection.
To enter a number greater than 10, use the (EW)
and {1 to [0 buttons.
Example:
To play from selection No.22
Press 10 (2) B].
(or E (2) (2)
To play from selection No.30
Press (10) (3) (td).
(or (3) m0)
functions as the number 0. !
Locating a Particular Point in a Selection
i
|
|
There are two ways to locate a desired point on a disc. |
i
i
!
|
A. To locate a point on the current disc while monitoring
the sound
Hold down «< or >> during play.
B. To tocate a point on the current disc quickly by
watching the display
Press Ul, then hold down <44 or >>. The search speed will
increase, but there will be no sound. Find the desired
point by watching the display.
Press ff or > again at the desired point to resume play.
“~ =” appears in the display
If you continuously press >> during play at the end of the disc. 5” !
appears in the display. Press << or i4 to return to the normal display
10

Replacing Discs While Playing a Disc
Replace discs in the compartments with new
To replace discs while playing a disc, use the EX-CHANGE ones.
button. You can open the disc tray and check what discs are
to be played next, or replace discs without interrupting
playback of the current disc.
The disc tray closes and playback continues.
Notes on EX-CHANGE
e Each time you press DISC SKIP while the disc tray is open, the disc tray
turns and two pairs of the disc compartments appear alternately, but the
compartment for the disc currently played does not appear to avoid two
discs being placed in one disc compartment.
e Do not turn the disc tray forcibly.
e You can use almost all of the functions to play the current disc while the
disc tray is open.
© If playback of the current disc ends while the disc tray is open, the player
stops playing. In one disc repeat mode, the current disc starts playing
again.
e In ALL DISCS shuffle mode, selections are reshuffled on the current disc
while the disc tray is open.
e In program mode, only the selections on the current disc are played.
When you open the disc tray by pressing EX-CHANGE
Do not push the disc tray to close it as you may damage the
player.
The disc tray turns and another two disc
compartments appear.

Playing
With
Sound
Effect
—
Digital
Signal
Processing
(CDP-C535 only)
You
can
listen
to
the
selections
with
five
acoustic
atmospheres
which
are
reproduced
by
the
Digital
Signal
Processing
(DSP)
circuitry
incorporated
with
the
CDP-C535.
These
atmospheres
are
produced
by
a
digital
processing
technique
that
involves
simulating
reflected
and
reverberated
sound
effects
and
digitally
compensated
frequency
response.
The
selected
DSP
mode
can
be stored in the memory of the player as a custom file (page 29).
Choosing the Desired DSP Mode
CDP-C535
b)
DIRECT
a) DIRECT
a) When using the main unit
Press the disired DSP mode button.
The indicator above the pressed button lights up.
b) When using the remote commander RM-D535
Press DSP SELECT repeatedly until the desired
DSP mode is selected.
SELECT
"
The indicator above the button for the selected DSP
mode lights up.
The DSP mode changes as follows:
[ HALL —> CHURCH - JAZZ CLUB ]
DANCE +— STADIUM
12
You can choose the sound effect from the following DSP
modes.
DSP mode Characteristic
HALL Reproduces the acoustics of a 2,000 seat
capacity concert hall.
CHURCH
Reproduces
the
acoustics
of
a
church
with
solid walls, staind glass interior, and high roof.
JAZZ CLUB Reproduces the acoustics of a modern jazz
club.
STADIUM Reproduces the acoustics of a 30,000 seat
capacity out door stadium.
DANCE Reproduces the acoustics of a discotheque
and features strong reverberation with a
dynamic bass.
Clearing the DSP Effect
Press DIRECT.
| RECT | or RECT
The indicator above the currently selected DSP mode button
goes off.

About the Sound Effect
The sound heard in a place such as a concert hall or a
movie theater consists of direct sound, early reflection, and
reverberation. the acounstic quality of a room depends on
how these three sounds are reproduced in the room. You
can estimate the size and the type of a room by listening to
the difference in these three sounds.
Types of sounds
, |
Early reflection Reverberation
Notes
¢ The DSP mode remains memorized after the power is turned off.
¢ You may hear noise when switching the DSP modes.
¢ When using the DSP effect, large outputs from this unit may cause
distortion to the sound from the amplifier. In this case, connect the
amplifier to the VARIABLE LINE OUT jack so that you can adjust the output
level with the LINE OUT/PHONE LEVEL control (or the LINE OUT LEVEL +/
-= buttons on the remote commander).
13

Fade-In/Fade-Out
Fading in and out allows you to record selections on your tape in such a manner that
play starts and stops gradually.
To fade out You can vary the fading time from 2 to 10 seconds while the
Press FADER during play at the point you want to start player is stopped. When a time is not specified, play will fade
fading out. “G~)” flashes in the display, play fades out and in and fade out for 5 seconds.
the player enters pause mode.
To fade in
Press FADER during pause.
“frag” flashes in the display, and play fades in.
*(‘*)” flashes and the actual fade time appears.
2 Press [2] - [10] to select fade time.
Example:
To set to 8 seconds, press [8].
14

Playing in a Random Order — Shuffle Play
Shuffle play allows you to play up to 99 selections in a random order. You can play
selections from all discs or only specified loaded disc(s).
Shuffle Play on All or One Disc
CONTINUE 2
DISC 1-5
Place the discs in the disc compartments.
Press SHUFFLE to choose ALL DISCS or 1 DISC.
SHUFFLE
-l
aisc
— ALL DISCS: The selections from all discs are
played in a random order.
- 1 DISC: The selections from the current disc are
played in a random order.
Shuffle play starts.
In 1 DISC mode, you can also use DISC 1-5.
To stop play
Press B.
To cancel shuffle play
Press CONTINUE to return to continuous play mode.
If you press SHUFFLE during continuous or program play
Shuffle play begins from the current selection.
What is this indication?
© ~ This indication appears while the player is “shuffling” the
l= sl) selections.
Shuffle Play on Specified Discs
— Select Shuffle Play
If you specify discs before or during play in ALL DISCS
shuffle mode, the selections on the specified discs only will
play in a random order.
To specify the discs
Press DISC 1-5 to specify the discs after choosing ALL
DISCS mode.
Semi-circles appear around the selected disc numbers to be
played. To cancel the selected discs, press DISC 1-5 again.
The semi-circles disappear.
To return to all shuffle play
Press SHUFFLE twice.
15

Playing in a Specified Order — Program Play
Program play allows you to specify the order of discs or selections to be played. You
can program up to 32 “steps” in the order you specify. One “step” may contain one
selection or a whole disc. You can check the total playing time while programming
the selections.
Program Play
2,3-B
CONTINUE
1 Place discs in the disc compartments,
then press .
“PROGRAM” appears in the display.
- If a program has been previously stored, it is
recalled. If you do not need the program, hold down
CLEAR to erase it (page 17).
3-A To program discs in the order you want
play
Press DISC 1-5 in the order you want to
program.
“AL” appears in the display.
- If you use DISC SKIP instead of DISC 1-5 to
choose the disc, press PROGRAM after that.
3-B To program selections on a disc in the order
you want to play
Before you program selections, specify the disc by
pressing DISC 1-5. There are two ways to program
selections.
occ | osca | osca | once | oses
1) Use the numeric buttons to choose
selections in the order you want to program.
3
Current disc Chosen Total playing time Chosen
selection selections
“AL” in the display disappears, then the selections
you choose will be programmed. Each time you
choose a disc or a selection, the playing time is
added to the total playing time. You can check the
total playing time while programming.
— To enter a selection number greater than 10,
see page 10.
- If you enter the wrong numbers:
Each time you press CLEAR, the last entered
number will be deleted.
~ To program the selection(s) on another disc,
press DISC 1-5 to change the disc. then
program selections.

3-B
2) Press I¢< or PPI to choose a selection to be
programmed, then press PROGRAM.
Repeat this to choose another selection.
— Before you press PROGRAM, you can check the
total playing time and change the selection to be
programmed. (Program Edit)
Program play starts.
To stop play
Press W.
You can play the same program repeatedly until you erase
the program.
To erase the program
Hold down CLEAR until “ALL CLr” appears in the display.
To cancel program play
Press CONTINUE to return to continuous play mode.
To recall the program you have made, press PROGRAM
again.
To make a program during play
Press PROGRAM, then follow step 3-A or 3-B. The program
will be played after the current selection.
lf the total playing time does not appear (only “STEP” appears)
You have programmed a selection number greater than 20 or the total
playing time exceeds 199 minutes and 59 seconds.
Hf you press PROGRAM during continuous or shuffle play
If a program has been stored, it will be played after the current selection.
if you replace discs
The program is stored until you erase it. If you replace discs, the program
operates on the new discs. The selection numbers not existing on the disc
are deleted from the program and the rest are played in the programmed
order.
If you turn off the player
The program is not erased. It is stored until you erase it.
a

Playing in a Specified Order
Recording Prorammed Selections
You can make a program to be recorded fit to your tape
length. By entering fl, you can divide a program into side A
and B. At the end of a program for side A, the player
automatically pauses before side A ends so that a selection
is not cut off.
1 Program the selections to be recorded on side
A of your tape by repeating steps 1 to 3 on
pages 16 and 17.
Press Il to program selections for side B.
“B” lights up.
Total playing time
will return to “0.00°.
The selections to be recorded on side A will be
programmed.
Program the selections for side B.
Repeat steps 1 to 3 on pages 16 and 17.
Start recording on the cassette deck,
then press >.
KE
Program play starts.
18
To play the selections for side B
Play automatically pauses at the point a pause is
programmed. Set the tape to the beginning of side B, then
press > or fl. The selections for side B will start playing.
Note
By pressing 88, a pause is programmed as a selection. The player counts
pauses as selections to be programmed.
To check the remaining time
Press TIME once to see the remaining time on the current selection, twice to
return to the initial display. The total remaining time does not appear during
program play.
Checking Your Program
Press CHECK. The first selection in the program appears.
Each time you press CHECK, the next selection in the
program appears. One of the tape indicators “:2.}" or
appears when the program for side A or B is being played or
checked.
Changing Your Program
To delete the last selection
Press CLEAR during stop. Each time you press CLEAR, the
last selection in the program will be deleted.
To delete a selection
Press CHECK repeatedly until the selection you want to
delete is displayed. Then press CLEAR.
To add selections to the end of the program
Press DISC 1-5 to select the disc and press the numeric
buttons for those selections. You can do this during stop.
play or pause.
To change the order
Hold down CLEAR to erase the program. Then repeat the
programming procedure from the beginning.
To make a program by referring to disc labeis
You can make a program while the disc tray is open. Follow
the steps 2 to 3 on page 16, then 4 on page 17. Program
Edit is not available.

Playing the Beginning of Each Selection
— Music Scan Play
You can sample the beginning of each selection on a disc. You can also check the
beginning of the first selection on each disc loaded. This is useful to check selections
in a disc or discs loaded in the player.
i To check the selections on the current disc
Music Scam-Play Press MUSIC SCAN in 1 DISC continuous play mode.
To check the first selection on each disc
Press MUSIC SCAN in ALL DISCS continuous play mode.
If you press MUSIC SCAN in program play mode
The beginning of each selection plays in the programmed
order. At this time the programmed pauses are ignored.
To stop music scan play
Press B.
MUSK SEAN To start play during music scan play
Press P. “>” lights up in the display and normal play starts.
if you press MUSIC SCAN during music scan play
Press MUSIC SCAN. The playing time of the selection is extended by 10, 20 or 30 seconds.
If you press << or >> during music scan
| Music scan is cancelled and normal play starts.
Each time you press MUSIC SCAN, the playing time of
each selection changes cyclically from 10 to 30 seconds.
“>” flashes in the display and the beginning of each
selection is played for the designated period.

Playing Repeatedly — Repeat Play
Repeat play allows you to repeat selections in any play mode. You can repeat all
discs, only specified discs, one selection, or programmed or reshuffled selections.
a) To repeat all selections
Hepralhlay Press REPEAT once. “REPEAT” appears in the display.
The player will repeat in the current play mode.
Playing mode Selections to be
repeated
Continuous play All selections on all
(ALL DISCS) discs
Continuous play All selections on the
(1 DISC) current disc
Shuffle play Selections on all discs
(ALL DISCS) (or selected discs) that the
player reshuffles
Shuffle play Selections on the
(1 DISC) current disc that the
player reshuffles
Program play All the selections in the
programmed order
b) To repeat the current playing selection (only during
continuous play)
Press REPEAT during repeat play. “REPEAT 1° appears
wu pe DIIDIMSN in the display.
ose Tn Lal
sc (Not operable during shuffle or program play.)
Bee)
c) To cancel repeat play
Press REPEAT until “REPEAT” or “REPEAT 1”
disappears.
eS. VIIDIADN Dano
a m nanom
IOo i 25 es HHH
20