Sony CDX-R3300T Product guide

SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the leads under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth leads to a common earth
point.
•Be sure to insulate any loose unconnected
leads with electrical tape for safety.
Notes on the power supply lead (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1and the protection collar 5are
attached to the unit before shipping. Before
mounting the unit, use the release keys 6to
remove the bracket 1and the protection collar
5from the unit. For details, see “Removing
the protection collar and the bracket (4)” on
the reverse side of the sheet.
•Keep the release keys 6for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Connection example (2)
Notes (2-B)
•Be sure to connect the earth lead before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Connection diagram (3)
1To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
•It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
•When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
•If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
•When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
5To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
3-261-419-11 (1)
Installation/Connections
安裝線路連接
© 2004 Sony Corporation Printed in Thailand
1
12
×4
3
4675
×2
Equipment used in illustrations (not supplied)
插圖中的裝置（非附送）
Power amplifier
功率放大器
Front speaker
前揚聲器
Rear speaker
後揚聲器
2
B
A
FM/AM
Compact Disc
Player
CDX-R3300T
CDX-R3000T
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
Active subwoofer
有源超低音揚聲器
AUDIO OUT REAR
1Catch

SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
BUS
AUDIO
IN
L
R
AUDIO
OUT
REAR
L
R
REMOTE IN
AUDIO OUT REAR*
from car aerial
來自汽車天線
2
5
4
AMP REM
7
Left
左
Right
右
Left
左
Right
右
RCA pin cord (not supplied)
RCA 針型插頭電線（非附送）
Max. supply current 0.3 A
最大源電流 0.3 A
Max. supply current 0.1 A
最大源電流 0.1 A
Fuse (10 A)
保險絲（10 A）
Red
紅色
Yellow
黃色
Black
黑色
Blue
藍色
Blue/white striped
藍白條紋
White
白色
Green
綠色
Purple
紫色
White/black striped
白黑條紋
Grey/black striped
灰黑條紋
Green/black striped
綠黑條紋
Purple/black striped
紫黑條紋
Grey
灰色
注意
•本機只能使用負極接地 12 V 直流電源。
•不要使導線夾在螺栓下，或繞掛在移動部件上
（如：座椅扶手上）。
•連接線路之前，請關閉汽車點火裝置以免引起短
路。
•黃色和紅色電源輸入導線必須在所有其它導線都
連接完畢以後才連接。
•將所有地線都連接到同一接地點。
•為了安全，請確認把沒有連接的導線用電器膠帶
包紮進行絕緣。
電源導線須知（黃色）
•將本機與其它立體聲裝置組合使用時，所連接
的汽車電路容量必須大於每個裝置保險絲容量
的總和。
•當汽車電路容量不夠大時，請將本機直接與電
池相連接。
零件一覽表（1）
•圖示數字與說明書中的數字是一致的。
•托架 1 和保護環 5 在出廠之前已經裝在本裝
置上。在安裝本裝置之前，請先使用開鎖鑰匙 6
將托架 1 和保護環 5 從本裝置上拆下。詳細
說明，請參見本頁反面“拆下保護環和托架
（4）”。
•如果要將本裝置從汽車上拆下，也要使用開鎖鑰
匙，因此請保存好開鎖鑰匙 6 以備今後使用。
注意
拿取托架 1 時，請特別注意別傷到手指。
註
安裝之前，必須將托架
1 兩側的拌鉤向內彎曲 2 mm。如
果拌鉤筆直或向外彎曲，則本裝置將無法牢固安裝，並可
能彈出。
線路連接圖例（2）
註 （2-B）
• 務必在接放大器之前連接地線 。
•
如果您連接了選購的功率放大器而不使用內置放大
器，將無提示聲功能
。
線路連接圖（3）
1連接至汽車的金屬表面
首先連接黑色接地導線，然後再連接黃色和紅色電源
輸入導線。
2連接至電動天線控制導線或天線升壓放大器的電源導線
註
• 如無電動天線或天線升壓器，或有手動套管式天
線，便不須連接此導線。
• 您汽車的後側玻璃窗中如果有內置 FM/AM 天線，
即請參看“控制線和電源線須知”。
3連接至選購的功率放大器的 AMP REMOTE IN（放大器
遙控輸入）
本連接僅用於放大器。連接任何其它系統可能會損壞
本機。
4連接至在點火鑰匙開關的附件位置上通電的 +12 V 電
源端子
註
• 若沒有附件位置，則請連接至始終通電的 +12 V 電
源（電池）端子。
必須首先將黑色接地導線連接至汽車的金屬表面。
• 您汽車的後側玻璃窗中如果有內置 FM/AM 天線，
即請參看“控制線和電源線須知”。
5連接至始終通電的 +12 V 電源端子
必須首先將黑色接地導線連接至汽車的金屬表面。
控制線和電源線須知
• 接通調諧器電源時，電動天線的控制導線（藍色）便
能提供 +12 V 直流電。
• 若您的汽車後側玻璃窗上有內置 FM/AM 天線，須將
電動天線控制導線（藍色）或輔助電源輸入導線（紅
色）連接到現有天線升壓器的電源端子上。詳細內容
請向銷售商諮詢。
•本機不能使用不具備繼電器盒的電動天線。
3
1
ANT REM
1
3
拌鉤
Notes on the control and power supply leads
•The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
•When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
•Apower aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
•Before connecting the speakers, turn the unit off.
•Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
•Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
•Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
•Do not attempt to connect the speakers in parallel.
•Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
•To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
•Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
保持記憶的線路連接法
當連接好黃色電源輸入導線時，即使汽車發動機點火鑰匙
關閉，電源仍將對記憶電路供電。
連接揚聲器時的注意事項
• 連接揚聲器電線以前，請先關閉本機電源。
• 使用阻抗為 4-8Ω 且具有足夠功率處理容量的揚聲
器，以免損壞揚聲器。
• 不要將揚聲器端子連接到車身上，或將右揚聲器端子
與左揚聲器端子相連接。
• 切勿將本機的接地導線連接至揚聲器的負(-)接線端。
• 揚聲器不可並聯連接。
• 請僅連接無源揚聲器。若將有源揚聲器（帶內置放大
器）連接到揚聲器端子上會損壞本機。
• 若本裝置使用左、右揚聲器的共用負極(-)導線，為了
避免故障，切勿使用已安裝在汽車內的內置揚聲器導
線。
• 請勿將本裝置揚聲器導線相互連接。
有關連接注意事項
如果未正確連接揚聲器和放大器，則顯示幕上會出現
“FAILURE”。此時，請正確連接揚聲器和放大器。
*AUDIO OUT can be switched to
REAR or SUB.
For details, see the supplied
operating instructions.
AUDIO OUT 可以轉換為 REAR 或 SUB。
詳情請參閱附帶的使用說明書。
Insert with the cord upwards.
電線向上插入。

SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
OPEN/EJECT
182 mm
53 mm
6A
to dashboard/centre console
至儀表板中央控制箱
Bracket
托架
Bracket
托架
max. size
5 ×8 mm
最大尺寸
5×8 mm
B
4
max. size
5 ×8 mm
最大尺寸
5×8 mm
TOYOTA NISSAN
4
to dashboard/centre console
至儀表板中央控制箱
Bracket
托架
Bracket
托架
4
Existing parts supplied with your car
隨汽車附送的部件
max. size
5 ×8 mm
最大尺寸
5×8 mm
max. size
5 ×8 mm
最大尺寸
5×8 mm
7AB
1 2
2
5
3
1
1
Fire wall
防火壁
Dashboard
儀表板
5
3
4
412
6
5
6
ccc
1
Existing parts supplied with your car
隨汽車附送的部件
(OFF)
Claws
鉤爪
Orient the release key
collectly.
正確定位開鎖鑰匙。
Face the hook inwards.
掛鉤朝裡面。
OPEN/EJECT

SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 5and the bracket 1from
the unit.
1Remove the protection collar 5.
1Engage the release keys 6together with
the protection collar 5.
2Pull out the release keys 6to remove the
protection collar 5.
2Remove the bracket 1.
1Insert both release keys 6together
between the unit and the bracket 1until
they click.
2Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outwards for a tight fit, if
necessary. (5-2)
•Make sure that the 4 catches on the protection
collar 5are properly engaged in the slots of the
unit. (5-3)
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A To detach
Before detaching the front panel, be sure to
press (OFF). Press , then pull it off towards
you.
7-B To attach
Attach part Aof the front panel to part Bof the
unit as illustrated and push the left side into
position until it clicks.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
使用前注意事項
•仔細選取安裝位置，以使本裝置不干擾正常的駕
駛操作。
•避免將本機安裝在受灰塵，污物和強烈振動影響
的區域，或安裝在高溫處，如直對陽光下或熱氣
管道附近。
•為了安裝安全和可靠，請使用附送的安裝構件。
安裝角度之調整
請在 45 度以內調整安裝角度。
拆下保護環和托架（4）
安裝之前，請先從本裝置上拆下保護環 5 和托架
1 。
1拆下保護環 5 。
1將開鎖鑰匙 6 與保護環 5 嚙合。
2拉出開鎖鑰匙 6 以拆下保護環 5 。
2拆下托架 1 。
1將兩把開鎖鑰匙 6 一起插入裝置和托架 1
之間，直至聽到喀嗒聲。
2向下拉托架 1 ，然後向上拉裝置，使之相
互脫離。
安裝示例（5）
安裝在儀表板裡
註
• 若有必要，則可彎曲這些卡爪。 （5-2）
•
必須將保護環 5 上 的 4 個鉤爪正確嚙合在裝置的卡槽
中。
（5-3）
將本機安裝於日本產汽車上時
（6）
有的日本產汽車不能安裝本機，在這種情形下，請
向 Sony 經銷商諮詢。
註
為防止發生故障，安裝時只能使用附送的螺絲
4 。
如何拆卸和裝配前面板（7）
安裝本機之前，請先拆卸前面板。
7-A 拆卸
拆卸前面板之前，須先按下 (OFF) 鍵。
然後，按下 鍵，朝您自己的方向拉出。
7-B 裝配
如圖所示，將前板的 A 處對準本機的 B 處，然
後將左側推入直至聽到喀嗒聲。
安裝在點火鑰匙開關上沒有 ACC
（附件）位置的汽車上時的警告
關閉汽車發動機後，必須按住 (OFF) 不放，
直至顯示消失。
否則顯示不會關閉，並耗費電池。
RESET 按鈕
當安裝和連接完成後，務請用原子筆等按壓 RESET
按鈕，然後拆卸前面板。