Sony CDX-4000X - Fm/am Compact Disc Player Product guide

S ON_Z,: 3.o,3-201.,,I
FM/AM
CompactDisc
Player
Installation/Connections
CDX-4OOOX
CDX-4005
Sony Corporation © 2000

2

Parts list
The numbers in the list are keyed to those
in the instructions.
0 ® ®
®
©®
®
Caution
Cautionary notice for handling the bracket
q).
Handle the bracket carefully to avoid
injuring your fingers.
×4

Installation
Precautions
• Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
• Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a
safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 60 o.
How to detach and attach the front panel
Before installing the unit, detach the front panel.
[] To detach
Before detaching the front panel, be sure to press
first. Then press _ to open the front
panel, then slide the front panel to the right side,
and pull out the left side of the front panel.
[] To attach
Place the hole (_) in the front panel onto the
spindle (_) on the unit as illustrated, then push the
left side in.
0
4

Mounting example
Installation in the dashboard
1
With the TOP marking up
Avec I'inscription TOPvers le haut
2
Bend these claws
outward for a tight fit,
if necessary.
Plier ces griffes pour
assurer une prise
correcte si n_cessaire.
3
Note
When installing this unit: Depending on car type, the mounting angle may not allow the front
panel to open easily. In such a case, remove the silver screw (_) shown below.
When screwing it on again, first lock the lever ®, Attaching the screw without doing so may cause the
unit to break,
S

Connections
Cautions
•This unit is designed for negative earth 12 V DC
operation only.
• Be careful not to pinch any wires between the
screw and the body of the car, or this unit. or
between any moving parts such as the seat
railing, etc.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Be sure to connect the red power input lead to
the positive 12 V power terminal which is
energized when the ignition key is in the
accessory position.
• Run all ground wires to a common earth
surface.
• Connect the yellow cord to a free car circuit
rated higher than the unit's fuse rating. If you
connect this unit in series with other stereo
components, the car circuit they are connected to
must be rated higher than the sum of the
individual component's fuse rating. If there are
no car circuits rated as high as the unit's fuse
rating, connect the unit directly to the battery. If
no car circuits are available for connecting this
unit, connect the unit to a car circuit rated higher
than the unit's fuse rating in such a way that if
the unit blows its fuse, no other circuits will be
cut off.
• The use of optical instruments with this product
will increase eye hazard.
8

Warning when installing in a car
without ACC (accessory) position
on the ignition key switch
Be sure to press _on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press _ only momentarily, the
clock display does not turn off and this causes
battery wear.
Reset button
When the installation and connections are
completed, be sure to press the reset button with a
ball-point pen, etc.
I
Frequency select switch
(CDX-C4005 only)
The AM (FM) tuning interval is factory-set to the
l0 K (200 K) position.
Make sure that the swich on the bottom of the
unit is set to the 9 K (50 K) position before making
connections.
Note
When you change the position of the switch to the
9 K (50 K) position, be sure to press the reset buttons
after the connections are completed.
Q

Connection diagram
Equipment used in illustrations
(not supplied)
@
Front speaker Rear speaker Power amplifier
10

Notes
•Be sure to connect the earth cord before
connecting the amplifier.
•If you connect an optional power amplifier and
do not use the built-in amplifier, the beep sound
will be deactivated.
11

Connection example
Front speakers
Haut-parleurs avant
Rear speakers
Haut-parleurs arri_re
from car antenna
de I°antenne de la voiture
RCA pin cord (not supplied)
Cordon _broche RCA (non foum0
Fuse(10 A)
Fusible (10 A)
12
Blue/white striped
bleu/blanc
AMP REM
To AMP REMOTE IN of an optional power ampfifier
Thisconnection isonly for amplifiers, Connecting
any other system may damage the unit.
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Left
White
Blanc
Light blue
Bleu ciel
Blue
Bleu
Max. supply current O.
Courant max. fourni O,

RotarycommanderRM-X4S(notsupplied)
Insertwiththecordupwards.
Fuse(10A)
Lightblue totheinterfacecableofacartelephone
vers le cordon de liaison d'un tdl6phone de voiture
ATT
Blue
Bleu
to the power antenna control lead or power supply lead of antenna
booster amplifier
Notes
•It is not necessary to connect this lead if there is no power antenna or
antenna booster, or with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/side glass, see
"Notes on the control and power supply leads."
Max. supply current 0.1 A ANT REM

Left
Gauche
Frontspeakers
Haut-parieursavant
Right
Droit
Left
Gauche
Rearspeakers
Haut-parleursarri6re
Right
Droll
White
Blanc
Black-striped
Noirraye
Gray
Gris
C°D
Black-striped
Noir raye
Green
Ve_
0
C:DBlack-striped
Noir ray_
Purple
Mauve
O
C-D
OBlack-striped
Noir ray_
Red
Rouge
Yellow
laurie
Black
Noir
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies + 12 V DC when you turn on the tuner.
•When your car has built-in FM/AM antenna in the rear/side glass,it isnecessary to connect the power antenna
control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster.
For details, consultyour dealer.
•A power antenna without relay box cannot be used with this unit.
Memory hold connection
When the yeflow power input lead isconnected, power will always be supplied to the memory circuit even when
the ignition key i5 turned off.
Notes on speaker connection
•Before connecting the speakers, turn the unit off.
•Usespeakers with an impedance of 4to 8ohms, and with adequate power handling capacities. Otherwise, the
speakers may be damaged.
• Do not connect the terminals of the speaker systemto the car chassis, and do not connect the terminals of the
right speaker with those of the left speaker.
• Do not attempt to connect the speakers in parallel.
• Do not connect any active speakers (with built-in ampfifiers) to the speaker terminals of the unit. Doing so may
damage the active speakers. Therefore, be sure to connect passive speakers to these terminals.
14

Red
Rouge
Yellow
Jaune
Black
Noir
0
to the +12 V power terminal which is energized in the accessory
positionofthe ignitionkey switch
Notes
•If there isno eccessoryposition, connect to the +12 Vpower (battery)
terminal which is energized at al! times.
Be sure to connect the black earth lead to it first.
• When your car has a built-in FM/AM antenna in the rear/side glass, see
"Notes on the control and power supply leads."
to the +12 V power terminal which isenergized at all times
Be sure to connect the black earth lead to it first.
to a metal surface of the car
First connect the black earth lead, then connect the yellow and red power
(£_ _input leads.

Mounting the unit in a Japanese
car
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
TOYOTA
(_) max. size 5 ×8 mm
Dimension max. 5 × 8 mm
to dashboard/centar console
au tableau de bord/console centrale
max. size
5x8mm
Dimension max.
5x8mm
pirates existantes fournies ave¢ la voiture
NISSAN
(_ max. size 5 x8 mm
Dimension max. 5 x8 mm
to dashboard/center console
au tableau de bord/console centrale
Bracket
Support
(_) max. size
5x8mm
Dimension max.
5×8ram
Bracket
Existing parts supplied to your car
Pi_ces existantes fournies avec la voiture
Note
To prevent malfunction, install only with the
supplied screws (_.
Sony Corporation Printed in USA