DSC-H1 4-3
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
Link
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50V or lessarenot indicated exceptforelectrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with *differ according to the model/destination.
Refer to the mount table for each function.
• Allvariableand adjustableresistorshavecharacteristic
curve B, unless otherwise noted.
• Signal name
XEDIT→ EDIT PB/XREC →PB/REC
•2: non flammable resistor
•5: fusible resistor
•C: panel designation
•A: B+ Line
•B: B– Line
•J: IN/OUT direction of (+,–) B LINE.
•C: adjustment for repair.
•A:VIDEO SIGNAL (ANALOG)
•A: AUDIO SIGNAL (ANALOG)
•A:VIDEO/AUDIO SIGNAL (ANALOG)
•A:VIDEO/AUDIO/SERVO SIGNAL
•A: SERVO SIGNAL
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
colorbar chartofpatternbox. Theyarereferencevalues
and reference waveforms.
(VOM of DC 10 MΩinput impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Precautions Upon Replacing CCD imager
• TheCD-576 boardmountedas arepairpart isnotequipped
with a CCD imager.
When replacing this board, remove the CCD imager from
the old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
1. Connection
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
Yellow
AABBA=B
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
CRT picture frame
H
Cyan
Green
White
Magenta
Red
Blue
Fig.b (Picture on monitor TV)
Note :
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièceportant lenumérospécifié.
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-450:
J-6020-250-A
For PTB-1450:
J-6082-559-A
Pattern box Color bar chart
Front of the lens
Pattern box
100 cm (PTB-450)
40 cm (PTB-1450)
