Sony CYBER-SHOT DSC-W1 User manual

SERVICE MANUAL
LEVEL 2
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Revision History
Revision History
DSC-W1/W12
How to use
Acrobat Reader
How to use
Acrobat Reader
•For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987673651.pdf).
•For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987673641.pdf).
• Reference No.search on printed wiring boards is available.
• Note in Lens Frame Installation
• Exchange Method of Barrier Assy
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Ver 1.2 2004.08
DIGITAL STILL CAMERA
On the CH-146, SY-102, SW-422, MS-204, MS-205 flexible, JK-263 and SP-045 flexible boards
Schematic diagram ............... Pages 4-9 to 4-28
Printed wiring board .............. Pages 4-39 to 4-48
Mounted parts location.......... Pages 4-54 and 4-55
Electrical parts list ................. Pages 5-7 to 5-8
and 5-10 to 5-13
The above-described information is shown in
service manual Level 3.
DSC-W1
US Model
Canadian Model
Hong Kong Model
Australian Model
Argentine Model
Brazilian Model
Tourist Model
Japanese Model
DSC-W1/W12
AEP Model
UK Model
E Model
Chinese Model
Korea Model
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside
the CH-146, SY-102, SW-422, MS-204, MS-205 flexible, JK-263
and SP-045 flexible boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-146, SY-102, SW-422, MS-204, MS-205
flexible, JK-263 and SP-045 flexible boards are not shown.
The following pages are not shown.

— 2 —
DSC-W1/W12
SPECIFICATIONS
xCamera
[System]
Image device
9.04 mm (1/1.8 type) color CCD
Primary color filter
Total pixels number of camera
Approx. 5 255 000 pixels
Effective pixels number of camera
Approx. 5 090 000 pixels
Lens Carl Zeiss Vario-Tessar
3 zo om lens
f = 7.9 – 23.7 mm (38 – 114 mm when
converted to a 35 mm still camera)
F2.8 – 5.2
Exposure control
Automatic exposure, Manual
exposure, Twilight, Twilight portrait,
Candle, Landscape, Beach, Soft snap
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent
File format (DCF compliant)
Still images: Exif Ver. 2.2 JPEG
compliant, DPOF compatible
Movies: MPEG1 compliant
(Monaural)
Recording media
“Memory Stick”
Flash Recommended distance (ISO set to
Auto):
0.2 m to 3.5 m (7 7/8 inches to 11 feet
57/8inches) (W)
0.3 m to 2.5 m (11 7/8 inches to 8 feet
21/2inches) (T)
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75 Ω, unbalanced,
sync negative
Audio: 327 mV (at a 47 kΩload)
Output impedance 2.2 kΩ
USB jack mini-B
USB communication
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel6.2 cm (2.5 type) TFT drive
Total number of dots
123 200 (560×220) dots
[Power, general]
Power AA Nickel-Metal Hydride batteries (2)
2.4 V
AC-LS5 AC Adaptor
(not supplied), 4.2 V
Power consumption (during shooting with
LCD screen on)
1.4 W
Operating temperature
0°C to +40°C (+32°F to +104°F)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Dimensions
91 ×60 ×32.9 mm
(3 5/8 ×2 3/8 ×1 5/16 inches)
(W/H/D, excluding maximum
protrusions)
Mass Approx. 250g (8.8 oz)(includingtwo
batteries, “Memory Stick” and wrist
strap)
Microphone
Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching II
Compatible
PictBridgeCompatible
xBC-CS2A/CS2B Ni-MH battery
charger
Power requirements
AC 100 to 240V 50/60Hz
3 W
Output voltage
AA : DC 1.4 V 400 mA ×2
AAA : DC 1.4 V 160 mA ×2
Operating temperature range
0°C to +40°C (+32°F to +104°F)
Storage temperature range
–20°C to +60°C (–4°F to +140°F)
Dimensions
71 ×30 ×91 mm
(2 7/8 ×1 3/16 ×3 5/8 inches) (W/H/D)
Mass Approx. 90 g (3 oz)
xAC-LS5 AC Adaptor (not supplied)
Input rating
100 V to 240 V AC, 50/60 Hz, 11 W,
0.16 A to 0.09 A
Output rating
4.2 V DC, 1.5 A
Operating temperature
0°C to +40°C (+32°F to +104°F)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Dimensions
Approx. 48 ×29 ×81mm
(1 15/16 ×1 3/16 ×3 1/4 inches)
(W/H/D, excluding projecting parts)
Mass Approx. 130 g (5 oz)
xAccessories
•HR6 (size AA) Ni-MH batteries (DSC-W1: 2,
DSC-W12: 4)
•Battery case (DSC-W1: 1, DSC-W12: 2)
•BC-CS2A/CS2B Ni-MH Battery charger (1)
•Power cord (mains lead) (1)
•USB cable (1)
•A/V connecting cable (1)
•Wrist strap (1)
•“Memory Stick” (32 MB) (1)
•CD-ROM (USB driver SPVD-012) (1)
•Operating instructions (1)
•Soft carrying case (DSC-W12 only) (1)
See page 5-15.
Design and specifications are subject to change
without notice.

— 3 —
DSC-W1/W12
1. Checkthe area ofyour repairfor unsoldered orpoorly-soldered
connections. Checkthe entire boardsurfacefor solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Lookfor parts which,through functioning, showobvioussigns
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

— 4 —
DSC-W1/W12
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Note for Repair ································································1-1
1-2. Discharging of the ST-101 Flexible Board’s Charging
Capacitors (C102 and C103) ···········································1-1
1-3. Note in Lens Frame Installation ······································1-2
1-4. Description on Self-diagnosis Display ····························1-2
2. DISASSEMBLY
2-1. Flow Chart ·······································································2-1
2-2. SY-102 Board Service Position ·······································2-3
2-3. Exchange Method of Barrier Assy ··································2-5
2-3-1.Peel Off Old Ornamental Ring A ····································2-5
2-3-2.Remove Old Barrier Assy················································2-6
2-3-3.Install New BarrierAssy ·················································2-6
2-3-4.Adhere the Ornamental Ring A ·······································2-7
2-4. Circuit Boards Location ··················································2-8
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2)···········································3-1
3-2. Overall Block Diagram (2/2)···········································3-3
3-3. Power Block Diagram (1/2)·············································3-5
3-4. Power Block Diagram (2/2)·············································3-7
4. PRINTEDWIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ··············································4-1
4-2. Schematic Diagrams························································4-5
CD-507 FLEXIBLE (CCD IMAGER) ····························4-7
ST-100 (FLASH DRIVE) ··············································4-29
ST-101 FLEXIBLE
(CHARGING CAPACITOR, FLASH UNIT) ···············4-29
US-011 FLEXIBLE (USB CONNECTOR)··················4-31
CONTROL SWITCH BLOCK ·····································4-32
4-3. Printed Wiring Boards ···················································4-35
CD-507 FLEXIBLE ······················································4-37
ST-100 ···········································································4-49
ST-101 FLEXIBLE ·······················································4-50
US-011 FLEXIBLE·······················································4-51
4-4. Mounted Parts Location ················································4-53
5. REPAIR PARTS LIST
5-1. Exploded Views ·······························································5-2
5-1-1.Cabinet Block Section ·····················································5-2
5-1-2.Main Block Section ·························································5-3
5-1-3.Lens Block Section··························································5-4
5-1-4.Side Frame Block Section ···············································5-5
5-2. Electrical Parts List ·························································5-6
Section Title Page

1-1
SECTION 1
SERVICE NOTE
DSC-W1/W12
1-2. DISCHARGING OF THE ST-101
FLEXIBLE BOARD’S CHARGING
CAPACITORS (C102 AND C103)
The charging capacitors (C102 and C103) of the ST-101 flexible
board are charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 kΩ/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
R:1 kΩ/1 W
(Part code:
1-215-869-11)
Capacitor
ST-101
ST kemikon sheet

1-2E
DSC-W1/W12
Display Code
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
whenyou cannot recoverfromthe
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit. When failed in the focus and zoom
initialization.
Abnormality when flash is being
charged.
Checking of flash unit or replacement
of flash unit. —
Insert batteries correctly. Batteries are not inserted correctly.
Batteries were installed or removed when
using the AC adaptor.
Turn the power off and on again.
E:92:ss
M1.4 ×4
Lens frame
Lens block assembly

DSC-W1/W12
2-1 2-2
2-1. FLOW CHART
The following flow chart shows the disassembly procedure.
SECTION 2
DISASSEMBLY
HELP
HELP
Note: When you exchange rings, be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
HELP
1Open two connectors (CN201, 701)
2Claw
x2
3Lens block
4CD-507: CN701
5Lens block flexible: CN201
13
4
5
5
0
qa
7
8
2
6
9
1
2
4
5
68
9
7
3
0
1Lock ace screw (M1.7) x4
2Claw
3Rear cabinet
4Side cover
5Sheet (S)
6Mic harness: CN102
7Lock ace screw (M1.7)
x2
8Front cabinet
1BT terminal flexible:CN001
2Tapping screw (M1.7)
x2
3SY-102
4MS-205 flexible: CN704
5Lock ace screw (M1.7)
x2
6Tapping screw (M1.7) x2
7Boss
8DC and A/V jack
9Claw
x2
0MS-205
1Lock ace screw
(M1.7)
x2
2SW-422
3US-011 flexible: CN101
4Lock ace screw
(M1.7)
x1
5Claw x4
6US-011
7Claw
x2
8Claw x2
9LCD block
0LCD flexible: CN801
qa Back light
flexible: CN802
1Claw
x1
2Claw x1
3Control SW block
4Control SW block flexible: CN702
5ST-101 flexible: CN601
6Claw
x2
7Strobo block
8Tapping screw (M1.7)
x1
9DC ground plate (B)
0Claw
x2
qa Claw x1
qs Bottom cabinet
3
qs
3
8
3
7
2
1
1
1
8
1
2
2
9
0
1
2
4
56
qa
0
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
4
5
6
7
R:1 kΩ/1 W
(Part code:
1-215-869-11)
Capacitor
ST-101
ST kemikon sheet
4
5
9
1Ornamental ring (A)
2Tapping screw (M1.2)
x2
3Barrier assy
12
3

DSC-W1/W12
2-3 2-4
2-2. SY-102 BOARD SERVICE POSITION
Lens block
LCD block
Stroboscope block
MS-205 flexible board
US-011 flexible board
SY-102 board
Control switch block
SW-422 board
Color monitor
AC power
adaptor AC IN
3
8
2
1
1
14
5
6
7
3
1
2
2
4
5
13
4
5
5
0
qa
7
8
2
6
9
1
2
4
5
68
9
7
3
9
qs
0
3
7
8
9
0
1
2
4
56
qa
0

2-5
DSC-W1/W12
2-3. EXCHANGE METHOD OF BARRIER ASSY
Service parts
Part Number Part Name Quantity
13-091-427-01 Ring (A), Ornamental 1
2X-3954-476-1 Barrier Assy 1
33-086-156-31 Tapping screw (P2) 2
Tools used
Torque driver
Soldering iron
Weight about 60g
Adhesive (Super X) (Note)
Note: Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
2-3-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force.
Heat four circled portions with the soldering iron.
Heating temperature is about 300ºC.
Beware of a burn since the entire Ornamental Ring becomes hot.
*As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame.
Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring.
*Take extreme care so as not to damage the coated surface of the group-1 frame.
In case of difficult peeling, heat the ring again with the soldering iron.
If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1→2→3→4in the under figure one
by one sequentially.
*Discard the removed Ornamental Ring A.
1
2
3
1
Tip
3
4
2

2-6
DSC-W1/W12
2-3-2. REMOVE OLD BARRIER ASSY
1Remove two screws.
*Discard the removed screws.
2Remove the Barrier Assy.
*Discard the removed Barrier Assy.
*After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position.
In returning the ring, adjust the location of a projection to the lens direction.
This is an important part to prevent the dust and light from coming in.
*After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-3-3. INSTALL NEW BARRIER ASSY
1Install new BarrierAssy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.
2Tighten two screws.
*Tightening torque = 0.5 kgf
1
1
2
Projection
2
2
1

2-7
DSC-W1/W12
2-3-4. ADHERETHE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy.
*Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.)
Meeting a “notch” of the Ornamental RingA with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame.
*The projection of the spring for preventing static electricity must be tilted.
Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens.
Note: Be careful not to give a shock.
*After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame.
A gap, if present, causes the crackle sound NG.
*The weight must push in the Ornamental Ring A only.
If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Completion after 30 minutes.
Notch
Adhesive Adhesive
Adhesive
Do not put the weight on a black mold part.
Not gap in full circumference.
Adhesive
Projection

2-8E
DSC-W1/W12
2-4. CIRCUIT BOARDS LOCATION
CD-507 flexible
US-011 flexible
SY-102
(including CH-146)
ST-101 flexible
ST-100
SW-422
CH-146
(included in SY-102)
JK-263
MS-205 flexible
MS-204 SP-045 flexible
Board Name Function
CD-507 flexible CCD IMAGER
CH-146 CCD SIGNAL PROCESS
(included in SY-102)
JK-263 JACK
MS-204 LCD DRIVE, MS CONNECTOR
MS-205 flexible CONNECTOR
SP-045 flexible SPEAKER
ST-100 FLASH DRIVE
ST-101 flexible CHARGING CAPACITOR, FLASH UNIT
SY-102 CAMERA MODULE, CAMERA DSP, LENS DRIVE,
(Including CH-146) SH DSP, FRONT CONTROL, DC/DC CONVERTER
SW-422 AUDIO, CONTROL SWITCH
US-011 flexible USB CONNECTOR

DSC-W1/W12
HELP
US-011 flexible board
Mic harness Front side
Sheet (S)
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

DSC-W1/W12
Link
Link
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (1/2)OVERALL BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (1/2)OVERALL BLOCK DIAGRAM (1/2)

DSC-W1/W12
3. BLOCK DIAGRAMS
3. BLOCK DIAGRAMS
LENS IRIS
(METER)
CCD
IMAGER
IC101
CD-507 FLEXIBLE BOARD (1/2)
SY-102 BOARD (1/2)
17
19
86
133
CAMERA
MODULE
(1/6)
AU AIN
V OUT
PANEL R
HR EN2,
HR DIR2A,
HR DIR2B
STRB CHRG
XSTRB FULL
ST UNREG
48 MCKTG
XFE CS, XTG CS
47
TG CLK
CP101
22
ı
35
40
ı
42
23
25
24
A12
B12
C23
B13
D13
C13
AC8
AC22
33
42
51
IRIS
MOTOR
M
LENS BLOCK
XFC RST SENS
XSYS RST
SYS V
1
OVERALL (2/2)
(PAGE 3-3)
2
OVERALL (2/2)
(PAGE 3-3)
USBPHY D±
FR SI, FR SO, XFR SCK
P4
C6
D7
F1
G1
AC12
AC15
Y11 AB11 Y10
AA11 AB10 Y9
AB9 AA10 AA9
Y8 AB8 AA8
AB7
AA7
U20 V21 V23 U22
V20
V22 W20 Y20
W22
Y23 W21 Y22
Y21
AA22 AA21 AB22
J21 L22 L20 L23 K21
L21
M21 M23 M20 M22
N21
N22 N20 P20 P21
P23
R21 P22 T21 R23
R20
R22 T20 T23 U21
L21 L23 M24 K23
H22
J21 J22 F24
K21
H21 M23 K22
G21
L24 F23 E23
V22 V21 V23 R22 W22
U22
W21 T22 R23 N21
P22
P21 P23 R21 M22
T21
P24 U21 U23 N22
U24
N23 T24 M21 T23
B16
B15
D16
IC304
51
IC501
CN701
(1/2)
LENS TEMP
IC201
ZOOM
MOTOR
M
ZOOM
FG
ZOOM
SENSOR
FOCUS
MOTOR
M
FOCUS
SENSOR
J1
K1
L1
M1
X301
54MHz
A: VIDEO SIGNAL
A: AUDIO SIGNAL
A: VIDEO/AUDIO SIGNAL
4
10
7
34
30
ı
28
26
ı
23
16
C1
D2
G5
H6
G4
H4
MC MSDIO,
MC MSBS,
MC MSCLK
BACKLIGHT
COLOR
LCD
MONITOR
D11
L7
L8
J11
L6
A5
B4
A4
A11
B11
C11
VR
VG
VB
COM
BL H
5
3
23
24
2
6
ı
8
11
ı
14
19
ı
22
4
CN801
3
CN802
D901
LCD901
RGT, HCK1, HCK2,
HST, PCG, XSTBY,
DWN, EN, VST,
VCK, REF, VP
HDO
PANEL V
LCD DRIVE
IC801
B1
A2
SYS V
MC D0 – D15
MC A1 – A25
Q602, 603
D8
J23
J22
AA12
D14
A17
C18
D21
AD16
K2
A7
H1
AA8
M
SHUTTER
MOTOR
LENS TEMP
SENSOR
24
ı
27
17
ı
20
5
ı
8
1
ı
4
29
21
VER EXT CLK
F4
F3
U3
T2
T3
U2
T4
AA19
AB20
E7
D7
MSHUT EN
MSHUT DIR
F8
F7
IRIS S EN
IRIS S IN
G2
G1
IRIS M EN
IRIS M IN
XZM DC BR
G3
H2
B1
FOCUS
MOTOR
DRIVER
ZOOM
MOTOR
DRIVER
IRIS
MOTOR
DRIVER
SHUTTER
MOTOR
DRIVER H8 MSHUT REF
HR EN0,
HR DIR0A
IRIS M±, S±
Z DC MOTOR ±
F MOTOR A, A, B, B
SHUTTER ±
CN201
BUFFER
Q102
IC301
XTG CS
XFE CS
CAM F
XSYS RST
MC XCS IC 301REG
MC XCS IC 301SDRAM
XSYS RST
XPANEL TG CS
XPANEL TG CS
VIDEO AMP ON
P1 MC CKIO
A2
A6
G2
AC12
AA9
AC16
AC15
AD19
AB11
LENS TEMP
VER EXT CLK
PANEL B
PANEL G
D1
E1
E11
F11
MS-205 FLEXIBLE BOARD (1/3)
MS-204 BOARD (1/3)
E1 F1 G2
H2 H1 J2
J1 K1 K3
L3
H11
K11
L10
PANEL UNIT
31
XZM RST SENS1
ZM DC FG A, B
F PI SENS OUT
Z PI SENS OUT
Z BOX1 PI SENS OUT,
Z BOX2 PI SENS OUT
IRIS M±, S±
ZOOM DC ±
FOCUS A, A, B, B
SHUTTER±
AU AOUT
A6
B5
A4
B4
1
3
5
6
36
35
33
32
11
7
26
27
31
7
11
30
31
19
135
37
48
9
6
12
15
19
10
13
17
20
113 109
112 115
125 119
118 121
6
37
5
2
4
20
19
21
36
1
3
7
8
10
11
9
12
ı
18
CAMERA DSP,
SDRAM
(KWF BOARD)
(2/6)
CA AD00 – CA AD13
AB6
46
CAM SO, XCAM SCK, XCAM RST
CAM SO, XCAM SCK, XCAM RST
CAM SO, XCAM SCK, XCAM RST
CLOCK
GENERATOR
(2/6)
LENS DRIVE
(3/6)
MSHUT REF
AA19
XZM DC BR
ST-100 BOARD
ST-101 FLEXIBLE BOARD
CN601
05
Q003
FLASH
UNIT
Q105
Q103
4
1
FLASH
CONTROL 4
2
IC001
VIDEO AMP
(2/6)
24
1
IC302
12
ı
17
Q604
XE_H CL025 – 030,
044, 045
CL038
CL039
CL041
CL801–803
CL804,
807, 808
CL811,
813, 814
CL001,
003 – 007,
042
TRIG 300V
XE_L
CL022
CL021, 043
+ +
C102, 103
CHARGING
CAPACITOR
D005
2
5 4
1
3
T001
STB FULL
ST UNREG
STB ON
XSTB FULL
STB ON
STRB CHRG
XSTRB FULL
STRB ON
AD14
AB7
MELODY
F1 PRELAMP AF CONT
H23
SELF TIMER LED
C22
XACCESS LED
L22
TALLY LED
AB5
XAE LOCK ON
AD20
XAE LOCK LED ON
AB13
XSHTR ON
AD11
FR INT
D11
XCS MC
MELODY ENV
D22
AA18
AU SEN
XAU LINE MUTE
BL LEV
LED A
LED K
BL H
OVERALL (2/2)
(PAGE 3-4)
3
C1
G10
13
11
9
CN704
(1/3)
CN001
(1/3)
14 BL L 1
BL L 27
B5
BL LEV
MC CAM,
SH DSP,
FLASH
(4/6)
CAM F
CAM F
Y7
45 CA HD
4
8
ı
10
12
ı
15
CCD OUT
POWER SAVE
20
V2, V4, V5A, V5B,
V6, V7A, V7B, V8
RG, H1B, H2B
V1A, V1B,
V3A, V3B
VHOLD
VST
21
VSUB
H1A, H2A
27
Q105
Q701
VSUB CONT
38
39
99
84
134 136 2 4
6 9 12 15
18 21 24
27 30 32
3 123
126
– 129
49 105
132
124
B7
B8
C7
C8
B3
A2
K4
J3
G4 J2 Y4
G3 H4 W4
N3
K3
M4
SYS SO, XSYS SCK
SYS SI, SYS SO, XSYS SCK
SYS SI, SYS SO, XSYS SCK
CH-146 BOARD
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
IC101
66 101 120
Q205
27MHz
3
TRANS
DRIVE
Q001, 002
XSTRB PWR SAVE XSTRB PWR SAVE
XSTRB PWR SAVE
19
17
2
8
6
21
10
4
13
11
9
14
CL810
CL812
CL817
CL815
CL816
CL820
CL821
CL819
27
19
17
2
8
6
21
10
4
CD-507 FLEXIBLE
BOARD (2/2)
CN701
(2/2)
39
Q702
LED
DRIVE
D101
SELF TIMER/
AF ILLUMINATOR
XLED
3-1. OVERALL BLOCK DIAGRAM (1/2)
3-1 3-2
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SECTION 3
BLOCK DIAGRAMS

DSC-W1/W12
3. BLOCK DIAGRAMS
3. BLOCK DIAGRAMS
A: VIDEO SIGNAL
A: AUDIO SIGNAL
A: VIDEO/AUDIO SIGNAL
USB JACK IN
SY-102 BOARD (2/2)
SW-422 BOARD
(1/2)
US-011 FLEXIBLE BOARD (1/2)
SW-422 BOARD (2/2)
US-011 FLEXIBLE BOARD (2/2)
AUDIO AMP
IC151
H7
F1
A7
05
MIC901
V OUT
AU AIN
AU AOUT
AU SEN
MELODY ENV
TALLY LED
XAE LOCK LED ON
XTALLY LED
XRSTX XRSTX
XAE LOCK LED
XCHARGE LED
XCHARGE/XSTRB LED
XCHARGE/XSTRB LED
MELODY
H6
H4
SP901
SPEAKER
V OUT V OUT
MIC IN
CN101
(2/3)
CN102
1
OVERALL (1/2)
(PAGE 3-2)
MODE
DIAL
S001
(SHUTTER)
POWER
CONTROL SWITCH BLOCK
S002
8XPWR ON
MODE DIAL0, 1 MODE DIAL0, 1
B8
B2
J8
J9
D1
D2
E1
6XPWR LED
D001
(POWER)
S901
USBPHY D±USBPHY D±
FR INT
XCS MC
XAE LOCK ON
IC401
D9
E2
DC/DC
CONTROL,
RESET
(6/6)
IC001
DDCON SO, DDCON SCK
C1
D3
L8
K8
D 1.2V ACV UNREG
PANEL 8.5V
BACK UP VCC
EVER 3.0V
A 3.1V
D 2.8V
CAM 15.5V
A 2.8V
CAM –7.5V/–8.0V
CAM 3.3V
ST 5V
M 5V
A7
H2
C7
D7
SYS SO, XSYS SCK SYS SO, XSYS SCK H2
H3
CN702
9
USB JACK IN
AV JACK IN
2
OVERALL (1/2)
(PAGE 3-2)
Q402
Q502
MODULATOR
SYS V
FR SI, FR SO, XFR SCK
B9
XSYS RST B3
J5
J4
D7
X401
32.768kHz
RESET
S201 – 208
1
2
KEY AD0, 1 KEY AD0, 1
KEY AD2
KEY AD0, 1
KEY AD2
CN101
(3/3) CN703
(3/3)
A2
A4
A3
C8 XMS IN
Q401
B6
AV OUT
(MONO)
2
3
(USB)
CN001
J101
MS-205 FLEXIBLE BOARD (2/3) SP-045 FLEXIBLE
BOARD
JK-263 BOARD
(1/2)
42
6
ı
10
1
ı
5
3
2
4
1
XSHTR ON
XAE LOCK ON
XPWR ON
XPOWER LED ON
CHG SW
FAST CHARGE
XRSTX
Q010
Q001
BATT/XEXT
CN704 (3/3) CN001 (3/3)
CN001
29
ACV UNREG1
+
−
JK-263 BOARD
(2/2)
MS-205 FLEXIBLE BOARD
(3/3)
MS-204 BOARD
(3/3)
DC IN
J102
BT901
BATTERY
TERMINAL
BATT UNREG
BATT GND
GND
J2
J3
VCC
ACV UNREG
ST UNREG
BATT UNREG
C1
XAU LINE MUTE G4
XSHTR ON
B1
FRONT
CONTROLLER
(5/6)
B1
G2
OVERALL (1/2)
(PAGE 3-2)
3
LED K
BL LEV
E4
E3
A9 BATT IN
H1 XCS DDCON K7
E8 SYS DD ON
G1 LED A
BATT/XEXT
Q503
LED
DRIVE
PLL
LOOP
FILTER
Q501
LED
DRIVE
D002
SELF TIMER/
RECORDING
D003
(AE/AF LOCK)
D004
(FLASH CHARGE)
21
2
10
11
1
7
15
23
24
CN703
(2/3)
28
30
31
CN101
(1/3)
12
14
16
10
19
5
7
15
22
CN703
(1/3)
3
AU AIN
26
XAU LINE MUTE
23 AU SEN
AU AOUT
SP±
21
BEEP
20
AU OUT
18
D±
XACCESS LED
XACCESS LED
MC MSDIO, MC MSBS, MC MSCLK MC MSDIO, MC MSBS, MC MSCLK MEMORY
STICK
4
2
8
6
MC MSDIO, MC MSBS, MC MSSCLK
XMS IN
MS-204 BOARD
(2/3)
CN901
2
33
9
10
BT001
LITHIUM
BATTERY
J6
H6
FUNCTION
KEY S002
W
S001
T
(ZOOM)
G6
VL 3V VL 3V
CL101–104
CL105–108
CL109
CL927
LND008, 009CL144, 145
CL924CL919 CL112
AU OUT
CL925
CL916
CL113
CL118
AV JACK IN
CL923 CL111
SP±SP±LND006, 007
CL922
CL901
44
46
48
50
43
45
47
49
42
29
44
46
48
50
43
45
47
49
CN704 (2/3) CN001 (2/3)
16
33
37
30
28
35
16
33
37
30
28
35
41 41
AU OUT
V OUT
SP±
AU OUT CL920
CL917
34 34
AV JACK IN CL918
XMS IN CL907
CL905,
909, 911
38 38
40 40
Q902
LED
DRIVE
D105
(MS ACCESS)
INITIAL
RESET,
BACK UP VCC
(6/6)
IC002
4 5
3
2
3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

DSC-W1/W12
3. BLOCK DIAGRAMS
3. BLOCK DIAGRAMS
POWER 2
(PAGE 3-7)
A
05
SY-102 BOARD (1/2)
CONTROL SWITCH BLOCK
VCH1A D 2.8V
VCH2
VCC1A
G11
ODP SW
C9
CHG SW
E4
VDCIN
D1
TLD
H6
CPSW
E8
OUT8B
E9
VCC8
B11
OUT8A
D9
L10
VCH1B K9
VCH1C (FB4) L9
VCH7 K3
VOS73 L3
VOS72 K4
E11
OUT2
F10
IC001
DC/DC CONTROL
(6/6)
VCC2
F9
VCH8A
C10
VCH8B
C11
VLDO1
A11
D 1.2V
M 5V
ST 5V
A 2.8V
VCC1C
G9
VCC1B
G10
BATT D4
MARK E5
OUT3C
J2
OUT3B
K1
VCH3A (FB3) J1
VCH3B H4
VCH3C (FB6) H3
VCH3S H2
VCC GD H1
D008
D012
D001, 002
BATT UNREG
D 1.2V
ACV UNREG
D 1.2V
ACV UNREG
L001, 002
L014
L015
L012
L003
VCH4 J6
OUT4 K6
CAM 15.5V
CAM 3.3V
VLDO4 C8 A 3.1V
L007
D010
BL THH
EVER 3.0V
IC401
FRONT CONTROLLER
(5/6)
ST UNREG
D 2.8V
G8
A7
ACV SENS
F8 DD CON SENS
BATT/XEXT
H8 BATT SENS
F003
F002
F001
F005
14
13
CN702
BACK UP VCC
6
ı
10
1
ı
5
OUT3A
J3
VCC5
DIN
CLK
SYSDDON
USB PWR ON
LD
FCHG
K5
VCC7 J4
Q010
Q003, 011
Q001
Q002
CN001
+
−
BT901
BATTERY
TERMINAL
BATT UNREG
BATT GND
DC CONTROL
VCH5 J5
OUT5 L5
CAM –7.5V/–8.0V
VLDO5 B8 PANEL 8.5V
LED A
L011
D009
VCH6 G1
OUT6 F1
LED K
BL LEV
ICH6 G2
REF6 B1
D006
D004
L006
L004 F004
DDCON SO,
DDCON SCK
C1
D3
L8
K8
H2
C7
D7
FAST CHARGE E3
A9 BATT IN
H1 XCS DDCON K7
E8 SYS DD ON
D001
(POWER)
D 2.8V
12
D 2.8V
42
CN704
(1/3)
CN001
(1/3)
ACV UNREG1
JK-263 BOARD
MS-205 FLEXIBLE BOARD
(1/3)
MS-204 BOARD
(1/3)
DC IN
J102
GND
BATT/XEXT
CL101–104
CL105–108
CL109
CL927 CL922
44
46
48
50
43
45
47
49
42
44
46
48
50
43
45
47
49
BT001
LITHIUM
BATTERY
D005
CN703
(1/2)
US-011 FLEXIBLE
BOARD (1/2)
33
VL 3V VL 3V
Q007, 008
SWITCHING
Q009
DC CONTROL
L013
D002
SELF TIMER/
RECORDING
D003
(AE/AF LOCK)
D004
(FLASH CHARGE)
INITIAL RESET,
BACK UP VCC
(6/6)
IC002
4
7VIN
6VOUT
CS
3VBAT
2VCH
3-5 3-6
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

DSC-W1/W12
3. BLOCK DIAGRAMS
3. BLOCK DIAGRAMS
SY-102 BOARD (2/2)
CN201
IC001
11
18
CN801
CN802
F PI SENS Vcc
PU[6]
Q201 (1/2)
REF
BL THH
VDD
Z BOX1 PI
SENS Vcc
05
6
1
ST UNREG
STRB CHRG
CAM DD ON
MS PWR ON
D 2.8V
ST 5V
BL THH
BL LEV BL LEV
PANEL 8.5V
LED A
LED K
BL THH
BL LEV
PANEL 8.5V PANEL 8.5V
PANEL 4.9V
PANEL 2.8V
PANEL 4.9V
PANEL 2.8V
BL H
BL L
MS-205 FLEXIBLE BOARD (2/3)
MS-204 BOARD (2/3)
BL L
3BL H
REF
BL THH
VDD
BL L
BL H
CAM 15V
CAM –7.5V
13
1
CN701
M 5V
38
L103
L102
L101
L104
FB105
FB102
CCD IMAGER
IC101
CD-507 FLEXIBLE BOARD
POWER 1
(PAGE 3-6)
CAM 15.5V
A 3.1V
D 1.2V
A 3.1V
D 1.2V
CAM 3.3V
CAM –7.5V/–8.0V
M 5V
A 2.8V
M 5V (AU_5V)
A 2.8V
D 2.8V
D 2.8V
D 1.2V
CAM 15.5V
CAM 3.3V
CAM –7.5V/–8.0V
M 5V
A 2.8V
D 2.8V D 2.8V
A
Q901
D 2.8V
Q106, 107
L152
REF
2.8V
REG
L802
L803
CN601
ST UNREG
ST 5V
CL025–030,
044, 045
CL001,
003–007,
042
CL040
AUDIO AMP
IC151
AC20
PU[0]
AD19
SDA(O/D)
AD18
ZOOM
SENSOR
LENS BLOCK
ZOOM
SENSOR
ZOOM
FG
3
CN704
(2/3)
M 5V (PANEL 5V)
1
A 2.8V (PANEL 2.8V)
27
14
12
3
CN001
(2/3)
1
27
14
10 10
12
IC802
H11
EXTDA G10
5 4
1.8V
REG
(4/6)
IC502
4 1
53
56
51
49
AU 2.8V
A 2.8V
AU 2.8V
A 2.8V
AU 5V
AU 2.8V
A 2.8V
AU 5V
28
9
Z PI SENS Vcc FOCUS
SENSOR
23
Z BOX2 PI
SENS Vcc
14
25
31
VIDEO AMP
(2/6)
IC302
L301
PI006 V4
VCC 9
XLENZ RST LED
PI007 V3 XZM RST LED
ST-100 BOARD
ST-101 FLEXIBLE
BOARD
T001
FLASH
UNIT
L601 Q602, 603 12
ı
17
2FLASH
CONTROL
BACKLIGHT
COLOR
LCD
MONITOR
D901
LCD901
LCD DRIVE
IC801
PANEL UNIT
CH-146 BOARD
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
CAMERA MODULE
(1/6)
IC101
CP101
FB103
FB101
FB102
FB307
FB303
FB903
FB309
D101
SELF TIMER/
AF ILLUMINATOR
CN704
(3/3)
25
31
CN001
(3/3)
MEMORY
STICK
MS-204 BOARD (3/3)
SW-422 BOARD
US-011 FLEXIBLE BOARD (2/2)
MS-205 FLEXIBLE BOARD (3/3)
CN901
IC501
MC CAM,
SH DSP,
FLASH
(4/6)
D2.8V
A 2.8V
M 5V
D 2.8V
D 2.8V
Q201 (2/2)
D 2.8V
IC304
IC301
CAMERA DSP,
SDRAM
(KWF BOARD)
(2/6)
CLOCK
GENERATOR
(2/6)
IC201
LENS DRIVE
(3/6)
54
55
71
52
57
L502
5 5
CL826–828
CL818,
824, 825
CL902,
928, 929
CL903
CL915,
932
CL809,
822, 823
CL810
CL806
CL804, 807, 808
CL801–803
24
16
13
14
CN703
(2/2)
17
8
5
6
CN101
3-4. POWER BLOCK DIAGRAM (2/2)
3-7 3-8E
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

DSC-W1/W12
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
F_MOTOR_B
F_MOTOR_A
Z_DC_MOTER_-
Z_DC_MOTER_-
CN102 2P
1 2
J101
J102
5P
CN001
1
89
67
VCC
2D-
3D+
4ID
5GND
10PCN001
1 2 3 4 5 6 7 8 9
10
31P
CN201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
17P
CN601
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17
CN702 14P
1 2 3 4 5 6 7 8 9
10 11 12 13 14
33P
CN703
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
50PCN704
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
27PCN101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
24P
CN801
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
CN802 6P
1 2 3 4 5 6
39P
CN701
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
CN901 12P
1
2
3
4
5
6
7
8
9
10
1
A
FLASH
CCD
BOARD
N
S
SCLK
SDIO/DATA0
DATA 1
DATA 2
DATA 3
VCC
VSS
INT
MS_BS
VSS
CN001 50P
BATTERY
TERMINAL
BT901
CONTROL
SWITCH
BLOCK
BOARD
CH-146
CP101
KWF
BOARD
IC301
SY-102 BOARD
OVF
CD-507
FLEXIBLE
BOARD
LENS BLOCK
UNIT
ST-100
ST-101
FLEXIBLE
BOARD
COLOR
LCD901
BACK
D901
LIGHT
LCD MONITR
2.5INCH
11
12
MEMORY
STICK
MEMORY STICK
MS-204
BOARD
PANEL UNIT
FLEXIBLE BOARD
MS-205
DC IN AV OUT
(MONO)
BOARD
JK-263
SP901
FLEXIBLE BOARD
SP-045
BOARD
SW-422
FLEXIBLE
BOARD
US-011
MIC
MIC901
(USB)
05
J
B
16
L
564 14
H
38
F
D
E
C
13 15
G
7 1711910 18122
K
I
TEST RGT B R G PSIG HCK1 HCK2 WIDE SOUT REF HST PCG XSTBY VSSG N.C. VSS VDD DWN EN VCK VST CS COM N.C. BL_L N.C. BL_THH BL_H BL_THL
REG_GND
REG_GND
REG_GND
KEY_AD0
REG_GND
REG_GND
N.C
REG_GND
AU_AOUT
A_2.8V
SYS_S0
XSYS_SCK
AU_2.8V
SP+
AU_SEN
AU_5V
BEEP
AU_5V
KEY_AD1
AU_AIN
REG_GND
SP-
REG_GND
AU_OUT
REG_GND
XAU_LINE_MUTE
N.C
MIC_IN MIC_GND
USBPHY_D+
REG_GND
NC
AU_5V
KEY_AD1
KEY_AD0
KEY_AD2
SP-
AU_AOUT
REG_GND
AU_SEN
SYS_SO
REG_GND
AU_OUT
A_2.8V
REG_GND
AU_5V
REG_GND
REG_GND
VL_3V
USB_JACK_IN
USB_GND
USBPHY_D-
USB_GND
REG_GND
SP+
REG_GND
REG_GND
XAU_LINE_MUTE
AU_AIN
BEEP
XSYS_SCK
AU_2.8V
REG_GND
XSYS_RST
HD0
PANEL_G
BL_L
PANEL_2.8V
PANEL_8.5V
V_OUT
BL_MODE
REG_GND
REG_GND
XMS_I
MC_MSB
REG_GND
REG_GND
PANEL_R
PANEL_B
REG_GND
D_2.8V
PANEL_V
REG_GND
PANEL_4.9V
XRSTX
MC_MSCLK
MS_PWR_ON
ACV_UNREG1
REG_GND
BL_H
XPANEL_TG_CS
MC_MSD3
MC_MSDIO
SYS_SI
ACV_UNREG1
SYS_SO
XACCESS_LED
SP+
AV_GND
ACV_UNREG1
BL_LEV
REG_GND
MC_MSD2
MC_MSD1
BATT/XEXT
AU_OUT
SP-
REG_GND
XSYS_SCK
BL_THH
AV_JACK_IN
ACV_UNREG1
STB_ON
ST_5V
XSTRB_PWR_SAVE
STB_FULL
REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND
ST_UNREG ST_UNREG ST_UNREG ST_UNREG ST_UNREG ST_UNREG
BATT_GND BATT_GND BATT_GND BATT_GND BATT_GND
BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG
EVER_3.0V
D_2.8V
XPWR_LED
MODE_DIAL1
XPWR_ON
XAE_LOCK_ON
XTALLY_LED
XSHTR_ON
XAE_LOCK_LED
MODE_DIAL0
NC
XCHARGE_LED
REG_GND
D_2.8V
CAM_-7.5V
GND
GND
RG
GND
H2A
H2B
GND
H1A
H1B
GND
GND
CAM_15V
GND
GND
CCD_OUT
NC
CCD_GND
POWER_SAVE
VSUB_CONT
VSUB
GND
V8
V7B
V7A
V6
VHOLD
V5B
V5A
V4
VST
V3B
V3A
V2
V1B
V1A
GND
M_5V
X_LED
SHUTTER_+
SHUTTER_+
SHUTTER_-
SHUTTER_-
IRIS_S_+
IRIS_S_-
IRIS_M_+
IRIS_M_-
Z_BOX1_PI_SENS_Vcc
Z_BOX1_PI_SENS_Col
GND
Z_BOX1_PI_SENS_OUT
Z_BOX2_PI_SENS_Col
Z_BOX2_PI_SENS_VCC
Z_BOX2_PI_SENS_OUT
GND
Z_DC_MOTER_+
Z_DC_MOTER_+
Z_PI_SENS_OUT
GND
Z_PI_SENS_VCC
F_MOTOR_A
F_MOTOR_B
F_PI_SENS_VCC
F_PI_SENS_OUT
GND
LENS_TEMP
4-1 4-2
4-1. FRAME SCHEMATIC DIAGRAM
FRAME
SECTION 4
PRINTEDWIRING BOARDS AND SCHEMATIC DIAGRAMS

DSC-W1/W12
Link
Link
4-2. SCHEMATIC DIAGRAMS
US-011 FLEXIBLE BOARD (USB CONNECTOR)
CONTROL SWITCH BLOCK
ST-100 BOARD (FLASH DRIVE)
ST-101 FLEXIBLE BOARD
(CHARGING CAPACITOR, FLASH UNIT)
CD-507 FLEXIBLE BOARD (CCD IMAGER) US-011 FLEXIBLE BOARD (USB CONNECTOR)
CONTROL SWITCH BLOCK
ST-100 BOARD (FLASH DRIVE)
ST-101 FLEXIBLE BOARD
(CHARGING CAPACITOR, FLASH UNIT)
CD-507 FLEXIBLE BOARD (CCD IMAGER)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS