Sony Vaio PCG-R505LE User manual

Confidential
SERVICE MANUAL
Notebook Computer
PCG-R505EL/R505ELK/R505ES/
R505ESK/R505ESP
S400
9-874-557-01
Ver. 1-2002E
Revision History
For American Area
US Model
Canadian Model
Lineup: PCG-R505EL
PCG-R505ELK
PCG-R505ES
PCG-R505ESK
PCG-R505ESP
•Design and specifications are subject to
change without notice.

– 2 – PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP (AM)
Confidential
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as
well as all precautions listed in the operating manual and other associated
documents.
2. Use designated parts only
The set’s components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the 0mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3. Always follow the original design when
mounting parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts or
routing wires, therefore, be sure to duplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6. When handling flexible print boards...
•The temperature of the soldering-iron tip should be about 270C.
•Do not apply the tip more than three times to the same pattern.
•Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
CautionMarkingsforLithium/IonBattery-Thefollowingorsimilar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
•Overcharging, short circuiting, reverse charging, multilation
or incineration of the cells must bi avoided to prevent one or
more of the following occurrences; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in surface
temperature.
•If a cell has leaked or vented, it should be replaced
immediately while avoiding to touch it without any protection.
Informationinthisdocument is subject to change withoutnotice.
Sony, VAIO and CLIE are trademarks or registered trademarks of
Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf
andother Microsoft products are trademarks or registeredtrademarks
of Microsoft Corporation in the United States and other countries.
The word Bluetooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, AMD logo, AMD Duron and
combinations thereof , 3DNow!, are trademarks ofAdvanced Micro
Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corporation.Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe logo and
combinations thereof are trademarks of Transmeta Corporation in
the USA and other countries. Graffiti, HotSync, PalmModem, and
Palm OS are resistered trademarks, and the Hotsync logo and Palm
are trademarks of Palm, Inc. or its subsidiaries. (M) and Motrola
aretrademarks of Motrora, Inc. Other Motrola products and services
with (R) mark like Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and services in this manual
are trademarks or registered trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not specified.

– 3 – PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP (AM)
Confidential
TABLE OF CONTENTS
Section Title Page
CHAPTER 1. BLOCK DIAGRAM ............................... 1-1
(to 1-2)
CHAPTER 2. FRAME HARNESS DIAGRAM ........ 2-1
(to 2-2)
CHAPTER 3. EXPLODED VIEWS AND
PARTS LIST
3-1. Main Section .................................................................... 3-2
3-2. LCD Section .................................................................... 3-5
3-3. Accessories ...................................................................... 3-7
(to 3-7)
CHAPTER 4. OTHERS
4-1. Replacing the CPU .......................................................... 4-1
(to 4-2)
•Abbreviations
UC : US model / Canadian model
History of the changes is shown as the “Revision
History” at the end of this data.

PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
FPC
SWX-151
CNX-151
CNX-153
Power SW
SWX-87
IFX-182 IFX-183
MDC
MDC
Baterry
BP2R/BP4R
CNX-152
IFX-180
VCH
FW82807
VCH
FW82807
FWH
E82802
FWH
E82802
GMCH-M
FW82830MG
GMCH-M
FW82830MG
ICH3-M
FW82801
ICH3-M
FW82801
VID
Selector
FM3565
VID
Selector
FM3565
Core
Voltage
Regulator
CLK GEN
IMI9870GTD
(CK-Titan)
CLK GEN
IMI9870GTD
(CK-Titan)
Primary IDE
i.LINK
TSB43LV22
i.LINK
0
Audio
CODEC
YMF753
Audio
CODEC
YMF753
Ext-MIC
Headphone
Amp
Amp
Ether
82562
Ether
82562 RJ-45
Cardbus
R5C476
Cardbus
R5C476II
PC Card
Socket
Super I/O
LPC47N227
Super I/O
LPC47N227 EC/KBC/SPIC
H8S/2149
EC/KBC/SPIC
H8S/2149
CN
SMBUS0
I/O Expander
/SMBUS MUX
OZ998
I/O Expander
/SMBUS MUX
OZ998
VGA
DSub-15
ITP
Connector
SMBUS0
Flash
BIOSROM
8 Mbit
CN
FAN
HDD
50pin
FPC
MDC
Connector
USB
Port0
FFC
CN
USB
Port1
EEPROM
(Password)
(ROMINFO)
EEPROM
(Password)
(ROMINFO)
PC133
Memory
BUS
AGTL
+
HL
HL
SMBUS2
PCI
LPC
SMBUS1
Battery
Connector
LCD
I/F
30pin
RJ-11
MS
Slot
MS
Chip
Debug
Port
Port0
Port1
Port2
Port3
Port4
USB Host
Controller0
CN
1
2
3
4
7
8
9
10
Docking Connector 100Pin
i.LINK
1
VGA
Ether
Pallarel
Serial
FDD
CN
FPC LED PWR/BATT/MS/W-LAN
DC Jack
Power
Supply
3.3V&5V
1.2V&1.8V
1.5V
Batt Charge
N.C
Port5
On Board Memory
Row#0
256Mbit x 4
PC133 SO-DIMM
144P Socket
Row#2,3
PC133 SO-DIMM
144P Socket
Row#2,3
ATF Sense
FAN Control
ADM1030
ATF Sense
FAN Control
ADM1030
SMBUS1
CPU
Pentum -m
&
Celeron
Processor
CPU
PentumIII-m
&
Celeron
Processor
uFCPGA
Connector
FFC
CN
FFC
CN
W-LAN
Module
802.11b
W-LAN
Module
802.11b
Mini PCI
124pin
Diversity Antenna
Speaker
Amp
Serial
Buffer
MAX3243
Serial
Buffer
MAX3243
PallarelSerial FDD
Int.KBD
Int.KBD
Touch PAD
Touch PAD
SWX-87
CN
CN
LCD 12.1" XGA
&
Inverter Board
LEX-32
5
6
8 9
1
2
CN
3
4
5
6
7
USB
Port5
USB
Port6
10
JogDial
L/R Button
SWX-88
AC LINK
CN
CN CN
CN
DVO
B
USB Host
Controller1
USB Host
Controller2
USB Port5
USB Port6
VGA
Ether
i.LINK
1
LED Caps/Num/ScrLk
LED Caps/Num/ScrLk
SMBUS1
SMBUS1
PCGA-DSM51
i.LINK
TSB43AB22
1-1 1-2
CHAPTER 1.
BLOCK DIAGRAM
(END)

PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
2-1 2-2
(END)
CHAPTER 2.
FRAME HARNESS DIAGRAM
18
1A
12
18
81
CN3001
Rear
LITHIUM ION
BATTERY PACK
24 1
CN1901
KEY BOARD
CNX-153 BOARD
SIDE B
CN4302
USB 10
1
CN4301
110 CN1111
FLEXIBLE FLAT
CABLE (10 CORE)
WIRELESS
LAN CARD
IFX-182 BOARD
IFX-183
BOARD
IFX-180 BOARD
SIDE A
CN4602
12
1
12
1CN1121
123 1
PC CARD
CONNECTOR
PC CARD
10
1
CN4601
MEMORY
STICK
21
79
80
CN1201
1
2
CN2801
CNX-154 BOARD
SIDE A
21
CN4402
CN4401
DC IN
130
CN701
LCD
LEX-32 BOARD
SIDE A
CN4901
INVERTER UNIT
HARNESS (LCD)
MODEM
CARD
J1
12
30
29
CN1602
CON2 CN5002
CN5001
MODULAR
JACK
CNX-152 BOARD
SIDE B
12
30
29
299
1 100
CN1401
DOCKING STATION
PCGA-DSM51
CN1502 RJ-45 HARNESS (FOR INTERNAL) NETWORK
2
10
1
9
CN2002
10
1
CN4801
CN4802
1
4
SPEAKER
R ch
SWX-87 BOARD
SIDE B
S4801
FLEXIBLE
FLAT CABLE
(10 CORE) POWER
SPEAKER
L ch
12
59 60
61 62
143 144
CN501
EXTENSION
MEMORY MODULE
PCGA-MM128E/MM256E
CN1394
1
16
49
1
50
2
CN2201
FPC (HDD)
HDD ASSY
PCG-R505EL, R505ELK: 30GB
PCG-R505ES, R505ESK, R505ESP: 40GB
CN4002
USB
J4004
MIC/LINE
INPUT
J4003
HEAD POHNE
CNX-151 BOARD
SIDE B
18
1
CN4001
i.LINK
DC OUT
118
CN1101
2
1
DC FAN
(WITH HEATSINK)
CPU
M
1
CN2001
20 2CN4701
112
CN4702
S4702
S4701 S4704 S4703
ENCODER
(ROTARY)
SWX-88 BOARD
SIDE A
TOUCH PAD CENTER
BUTTON
LEFT
BUTTON RIGHT BUTTON
FLEXIBLE FLAT CABLE (20 CORE)
FLEXIBLE FLAT CABLE (12 CORE)
NICKELHYDROGEN
BATTERY
CN2802
21
19 1
10
1
CN4703
19
FLEXIBLE PRINT (LED) PWB
Side L Side R
2
20
FLEXIBLE PRINT
(ILINK) PWB
HARNESS (POWER 2P)
FLEXIBLE
FLAT CABLE
(12 CORE) FLEXIBLE FLAT CABLE
(NI SHIELD) 18P
HARNESS (2PIN)
From board to connector
(direct connection)
Harness
(with connectors on both ends)
Harness (soldering on either end)
MBX-62 BOARD
SIDE A
(PCG-R505ES, R505ESK,
R505ESP)
CN2101

3-1 PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
CHAPTER 3.
EXPLODED VIEWS AND PARTS LIST
NOTE:
•Items marked “ *” are not stocked since they are seldom
required for routine service. Some delay should be
anticipated when ordering these items.
•The mechanical parts with no reference number in the
exploded views are not supplied.
•When two or more parts are shown in parallel, use the part
described first as the main part.
•The parts marked “ $ ” are the High Value Modules.
•The parts marked“ # ”are the parts on which barcode label
is attached.
For the barcode label, refer to CHAPTER 4.
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

3-2 PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
53 1-823-816-11 CABLE, FLEXIBLE FLAT
54 4-654-610-03 COVER AIR DUCT
55 X-4624-450-1 HOUSING (BOTTOM) ASSY
56 4-662-966-01 SPACER (VGA)
57 4-663-912-01 (R505ES, R505ESK, R505ESP)...
ADHESIVE TAPE (5X80)
58 4-662-893-01 SHEET, POWER HEAT SINK GROUND
59 4-663-129-01 PLATE (PALMREST), INTERCEPTION
60 4-662-968-01 REINFORCEMENT, KEYBOARD
61 X-4625-015-2 COVER (REAR L) ASSY
62 X-4623-577-5 LID (DOG) ASSY
63 1-961-661-12 HARNESS, RJ-45
64 4-660-016-01 COVER (REAR R)
65 4-657-622-01 FOOT (R2)
66 1-683-865-11 PWB, FLEXIBLE PRINT
*67 4-660-022-01 BRACKET (HDD)
69 1-790-750-13 FPC (HDD)
70 A-8059-666-A (R505ES, R505ESK, R505ESP)...
ASSY HDD 40GB (T, 20, F) (S)
70 A-8059-226-A (R505EL, R505ELK)...
HDD (30GB, IC25N030ATCS04-0) (S)
71 4-641-449-01 FOOT (F)
72 X-4624-453-1 DOOR (VGA) ASSY
73 A-8110-724-A (R505ES, R505ESK, R505ESP)...
MBX-62 (256A) (S)
73 A-8110-726-A (R505EL, R505ELK)...
MBX-62 (128A) (S)
74 4-649-669-11 CUSHION IFX
*75 4-660-052-01 HOLDER, ALMADOR
*76 4-660-053-01 FIN, ALMADOR
77 4-660-067-01 COVER (BOTTOM R)
78 4-660-524-01 SHEET (COIL), THERMAL
79 4-662-616-01 GASKET (FAN 1)
80 4-662-778-01 SHEET (HDD), SHIELD
81 4-662-843-01 SHEET (CS), SHIELD
82 4-662-881-02 CUSHION, KEYBOARD
83 4-662-354-01 COVER (HDD)
84 6-701-337-11 (R505ES, R505ESK, R505ESP)...
IC RH80530GD009512
84 6-700-582-11 (R505EL, R505ELK)...
IC RH80530GD006512
85 4-664-561-01 ADHESIVE TAPE
86 4-665-662-01 SPACER (HINGE) (2)
B1 4-662-967-01 SCREW (2 TAPPING) (2X4)
B2 4-662-756-01 SCREW (1.4 TAPPING) (1.4X3.5)
B3 4-654-273-31 ACE (M2), LOCK (2X3.5)
B4 4-654-273-21 ACE (M2), LOCK (2X13)
B5 4-651-989-31 SPACER (MBX)
B6 4-635-966-01 SCREW (HEX)
B7 4-635-301-01 SCREW M3X4
B8 4-644-492-01 ACE (M2), LOCK (2X6)
B9 4-654-273-01 ACE (M2), LOCK (2X5)
B10 4-645-016-01 ACE (M2) (DIA. 4.6), LOCK (2X3)
Ref.No. Part No. Description
1A-8067-340-A COMPLETE PWB SWX-88
21-823-811-11 CABLE, FLEXIBLE FLAT 20P
31-763-819-11 PWB, FLEXIBLE PRINT (FRONT LED)
41-476-762-32 ENCODER (ROTARY)
5X-4624-454-2 (R505ES, R505ESK, R505ESP)...
HOUSING (PALMREST) (A) ASSY
5X-4624-466-2 (R505EL, R505ELK)...
HOUSING (PALMREST) (B) ASSY
64-660-060-01 (R505ES, R505ESK, R505ESP)...
COVER (PALM), LENS
64-660-223-01 (R505EL, R505ELK)...
COVER (PALM) (B), LENS
74-660-058-01 (R505ES, R505ESK, R505ESP)...
KNOB, SLIDE
74-660-603-01 (R505EL, R505ELK)...
SPACER (LENS COVER)
84-654-382-01 CUSHION HDD CONNECTOR
91-796-319-11 PAD, TOUCH
10 4-660-059-02 ESCUTHEON (PAD)
11 1-823-813-11 CABLE, FLEXIBLE FLAT 12P
12 X-4624-451-1 COVER (SIDE L) ASSY
13 4-660-456-01 CUSHION (COVER SIDE)
14 X-4624-452-1 COVER (SIDE R) ASSY
15 1-825-082-11 SPEAKER, (2.0CM) BOX WITH
16 4-662-617-01 SHEET (FAN), INSULATING
17 1-823-812-11 CABLE, FLEXIBLE FLAT 10P
18 A-8067-331-A COMPLETE PWB SWX-87
19 X-4624-593-2 HOUSING (FRAME) ASSY
*20 4-660-019-01 KEYBOARD, PLATE
21 4-660-020-01 COVER, HINGE
22 1-960-827-51 HARNESS (2PIN)
23 A-8067-316-A COMPLETE PWB CNX-152
24 4-653-506-13 SHEET (MODEM)
25 1-477-114-21 KEYBOARD UNIT (US)
*26 1-763-809-11 FAN, DC (WITH HEATSINK)
27 4-660-523-01 SHEET (CPU), THERMAL
28 4-662-258-01 SHEET (MS), INSULATING
29 A-8067-323-A COMPLETE PWB IFX-180
30 1-823-814-11 CABLE, FLEXIBLE FLAT 12P
31 X-4624-494-1 ASSY BRACKET WIRE
32 1-761-380-23 CARD, MODEM
33 X-4624-743-1 ASSY COVER (BATTERY LOCK)
34 6-700-666-01 (R505EL, R505ELK)...
IC HYS64V16220GDL-7.5-C2
35 4-662-355-01 (R505ES, R505ESK, R505ESP)...
SHEET (WL), INSULATING
36 1-761-495-11 (R505ES, R505ESK, R505ESP)...
CARD, WIRELESS LAN
37 1-756-038-21 BATTERY, NICKEL HYDROGEN
*38 4-660-056-01 BRACKET (CPU)
*39 4-660-024-01 BRACKET (VGA)
40 4-654-239-01 INSULATING SHEET
41 4-660-018-02 INSULATOR (BOTTOM)
42 A-8067-325-A COMPLETE PWB CNX-154
43 1-779-745-31 JACK, DC
44 1-961-555-11 HARNESS (POWER 2P)
45 A-8067-324-A COMPLETE PWB CNX-153
46 1-793-100-11 CONNECTOR, USB
47 1-823-815-11 CABLE, FLEXIBLE FLAT 10P
*48 4-660-023-01 PLATE (PC CARD)
49 1-816-270-11 CONNECTOR, PC CARD
50 A-8067-317-A COMPLETE PWB CNX-151
51 1-816-281-11 JACK, SMALL TYPE (MICROPHONE)
52 1-695-514-21 JACK (SMALL TYPE) 1P (HEADPHONE)
3-1. MAIN SECTION
Ref.No. Part No. Description
*When change the CPU (ref. 84), refer to “Replacing the CPU”
on page 4-1 and 4-2.

PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
3-3 3-4
46 44
43
45
B3
B3
B3
B3
B3
B3
B9
B3
B3
B3
B3
B6
B9
B5
B4
B5
B5 B10
B10
B5
B5
B10
B3
B3
B3
B3
B8
B8
B8
B7
B7
B3
B3
B3
B3
B9 B9
B1
58
82
B1
B9
B3
B9
B9
B1
B2
B2
B2
B3
B3
B3
B3
47
46 52
51
50
54
53
72
14
13
3
59
2
1
4
5
6
7
8
9
10
12
13 11
49
8
48
71
69 70
83
67
66
55
65
64
63
65 62
41
40
57
42
38
80
74
74
56
79
37
26 84
28
29
30
31
76
81
32
33
34
39
73
6
7
15
78
75
16
17
18
19
20
21
25
21 60
22
23
24
1
2
3
4
6
8
5
wj
qa
qk
wf
ql
wg
wd qj
qh
ef
ek
el
ek
el
ek
el
qk
9
0
qs
ej
ej
qd qh
1
2
L
I
M
F
N
K
P
DO
wj
qs
5
A
JHQwg 3
4
wd
qg
6wa
es
ea ws
e;
8
wh
qa
qf
qd
qg
wk wa
ql
ea
w;
e;
ed
90
qj
P
Q
O
es ws
L
K
M
wk
ed
qf
wf wl
N
I
F
wl
J
w;
eh
wh
A
E
E
G
G
H
D
BC
77
ef
eg
eg
eh
36
27
35
B
C
PCG-R505ES, R505ESK,
R505ESP
PCG-R505ES, R505ESK,
R505ESP
PCG-R505ES,
R505ESK, R505ESP PCG-R505EL, R505ELK
PCG-R505EL,
R505ELK
85
61
86
*When change the CPU (ref. 84), refer to “Replacing the CPU”
on page 4-1 and 4-2.

PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
3-5 3-6
3-2. LCD Section
C
C
B
1
2
2
3
4
3
3
5
5
4
2
1
A
B
A
122
123
B11
B11
B10
B10
B10
B10
B11 B10
119
B10
126
120 B10 126
121
121
118
116
115 125
117
114
104
105
107
106 111
109
108
B10
B11
109
108
112
113
124
124
PCG-R505ES, R505ESK,R505ESP PCG-R505EL, R505ELK
110
101
103
102
Ref.No. Part No. Description
101 X-4624-594-2 HOUSING (BEZEL) ASSY
102 4-660-030-01 LATCH
103 4-639-623-11 SPRING (LATCH), COIL
104 4-660-035-01 COVER (DL)
105 4-660-036-01 COVER (DR)
106 4-660-039-01 BLIND (LCD B), HOLE
107 4-663-773-11 (R505ESP)...LABEL (ID) (U)
107 4-663-773-21 (R505ESK)...LABEL (ID) (U)
107 4-663-773-31 (R505ES)...LABEL (ID) (U)
107 4-663-773-41 (R505EL)...LABEL (ID) (U)
107 4-663-773-81 (R505ELK)...LABEL (ID) (U)
108 4-652-933-02 BLIND (SIDE), HOLE
109 4-660-038-01 BLIND (LCD), HOLE
110 4-652-938-02 CUSHION (LATCH)
111 1-961-579-11 HARNESS (LCD)
*112 4-660-031-01 BRACKET (LCD-L)
*113 4-660-032-01 BRACKET (LCD-R)
114 A-8059-714-A LCD (12.1)(H)(S)
115 A-8067-333-A COMPLETE PWB LEX-32
116 1-476-317-12 INVERTER UNIT
*117 4-660-033-01 TILT UNIT (L)
*118 4-660-034-01 TILT UNIT (R)
119 A-8067-327-A (R505ES, R505ESK, R505ESP)...
COMPLETE PWB IFX-182
120 A-8067-328-A (R505ES, R505ESK, R505ESP)...
COMPLETE PWB IFX-183
121 1-823-844-11 (R505ES, R505ESK, R505ESP)...
CABLE, COAXIAL
122 X-4624-449-1 HOUSING (DISPLAY) ASSY
123 4-660-029-01 COVER (DISPLAY)
124 4-662-650-01 (R505ES, R505ESK, R505ESP)...
GASKET (W-LAN)
125 4-649-669-11 CUSHION IFX
126 4-663-174-02 (R505EL, R505ELK)...SPACER (W-LAN)
B10 4-645-016-01 ACE (M2) (DIA. 4.6), LOCK (2X3)
B11 4-643-356-01 SCREW (M2X5)

3-7 PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
(END)
3-3. Accessories
Ref.No. Part No. Description
ACCESSORIES
***********
0201 1-757-562-21 CORD, POWER
202 A-8067-456-A BP2R (U) ASSY (S)
0203 1-477-205-31 ADAPTOR, AC
4-646-847-11 (R505ELK, R505ESK)...
W2K FIRST STEP GUIDE
4-664-856-01 QUICK START
LOOK AT EXPLODED VIEWS OF THE PART
**********************************
204 PCGA-DSM51
201
Power Cord
202
Battery Pack
203
AC Adaptor
204
Docking Station
(PCGA-DSM51)
* The main unit is not assigned with a part number.
Refer to the PCGA-DSM51 Service Manual
(9-874-565-01).
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité. Ne les
remplacer que par une pièce portant le
numéro spécifié.

PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP
(AM)
Confidential
4-1. Replacing the CPU
Note: We have two kinds of CPU for this set, and either of them is used.
Two kinds of CPU have differences in the lock position and the unlock position.
1. Socket configuration 1 2. Socket configuration 2
4-1 4-2
1. How to remove the CPU
2. How to install the CPU
(FOX)
lock position
unlock position
unlock position
lock position
1Rotate the lock with a flat-blade screwdriver toward
the unlock position shown in the figure.
2Remove up the CPU.
2
CPU
1Position the mark on the CPU to the mark on the CPU
socket and put in all pins to the holes on the CPU socket.
2Pressing two corners marked with in the figure,
rotate the lock with a flat-blade screwdriver toward
the lock position.
(FOX)
mark
mark
Note: Lock the CPU properly, or operation
becomes unstable.
CPU socket
CPU socket
1
CPU
2
2
(AMP)
1
2
2
CPU
(AMP)
1
CPU
1. How to remove the CPU
lock position
unlock position
unlock position
lock position
1Rotate the lock with a flat-blade screwdriver toward
the unlock position shown in the figure.
2Remove up the CPU.
mark
CPU socket
CPU socket
2. How to install the CPU
1Position the mark on the CPU to the mark on the CPU
socket and put in all pins to the holes on the CPU socket.
2Pressing two corners marked with in the figure,
rotate the lock with a flat-blade screwdriver toward
the lock position.
mark
Note: Lock the CPU properly, or operation
becomes unstable.
(END)
CHAPTER 4.
OTHERS

– 17 –
Model Service Manual
Parts No.
PCG-R505TE
PCG-R505TEK 9-872-185-11
PCG-R505TS
PCG-R505TSK
PCG-R505DE 9-874-420-11
PCG-R505TL 9-874-442-11
PCG-R505TLK
PCG-R505JE
PCG-R505JEK
PCG-R505JEP
PCG-R505JL
PCG-R505JLK 9-874-469-01
PCG-R505JLP
PCG-R505JS
PCG-R505JSK
PCG-R505JSP
PCG-R505AFE 9-874-490-01
PCG-R505DL
PCG-R505DS 9-874-513-01
PCG-R505DSK
PCG-R505DSP
PCG-R505EL
PCG-R505ELK
PCG-R505ES 9-874-557-01
PCG-R505ESK
PCG-R505ESP *: Additional Model
American Area : North, Central and South Americas
PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP (AM)
This manual and the constituent data may not be
replicated, copied nor reprinted in whole or in part
withoutprior writtenauthorization of SonyCorporation.
List of PCG-R505 Series for AmericanArea
(As of May, 2002)
*
Sony Corporation
9-874-557-01
English
2002E0500-1
© 2002 Sony Corporation
Published by Sony EMCS VAIO-GSC [SNT]

Revision History
Suffix Ver. Date Contents QM No.
<Remarks>
[Confidential]
PCG-R505EL/R505ELK/R505ES/R505ESK/R505ESP (AM)
-01 Ver. 1 2002.05.27 First Edition