Sony KP 43T90 User manual

COLOR REAR VIDEO PROJECTOR
SERVICE MANUAL RA-3B CHASSIS
MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.
KP-43T90 RM-Y906 US/Canada/Mexico SCC-P62A-A
KP-48V90 RM-Y906 US/Canada/Mexico SCC-P62D-A
KP-53V90 RM-Y906 US/Canada/Mexico SCC-P62C-A
KP-61V90 RM-Y906 US/Canada/Mexico SCC-P62B-A
9-965-907-01
Self Diagnosis
Supported model
KV-53V90 RM-Y906

— 2 —
KP- 43T90 / 48V90 / 53V90 / 61V90
TABLE OF CONTENTS
Specifications ...................................................................... 3
Warnings and Cautions ....................................................... 4
Safety Check-out ................................................................. 5
Self-Diagnostic Function...................................................... 6
1. Disassembly
1-1. Rear Board Removal ........................................................... 9
1-2. Chassis Assembly Removal ................................................ 9
1-3. Service Position ................................................................... 9
1-4. HA and HB Board Removal (Except KP-43T90) ................. 10
1-5. HA and HB Board Removal (KP-43T90 only)...................... 10
1-6. Beznet Assembly Removal.................................................. 10
1-7. Mirror Cover Removal.......................................................... 11
1-8. HC Board and S Board Remvoal......................................... 11
1-9. A and G Board Removal...................................................... 11
1-10. HV Cable Installation and Removal ..................................... 12
1-11. Picture Tube Removal.......................................................... 12
2. Set-up Adjustments
2-1. Screen Voltage Adjustment.................................................. 13
2-2. Screen (G2) Adjustment ...................................................... 13
2-3. Deflection Yoke Tilt Adjustment............................................ 13
2-4. Focus Lens Adjustment ....................................................... 14
2-5. Focus Control Adjustment ................................................... 14
2-6. 2-Pole Magnet Adjustment .................................................. 15
2-7. 4-Pole Magnet Adjustment .................................................. 15
2-8. Defocus Adjustment............................................................. 15
2-9. Electrical Adjustments By Remote Commander.................. 16
2-10. Registration Adjustment (PJE mode only)........................... 21
2-11. Green Registration Adjustment ........................................... 22
2-12. Red Registration Adjustment............................................... 23
2-13. Blue Registration Adjustment .............................................. 23
2-14. Auto Registration Adjustment .............................................. 24
3. Safety Related Adjustments (G Board)
3-1. HV Regulation Circuit Check and Adjustment ..................... 25
3-2. HV Hold Down Circuit Operation Check and Adjustment .... 25
3-3. +B Max Voltage Confirmation .............................................. 26
3-4. +B OVP Confirmation .......................................................... 26
4. Circuit Adjustments
4-1. TV Input Sub Contrast Adjustment ...................................... 27
4-2. Video Input Sub-Hue and Sub Color Adjustment ................ 27
4-3. Component Input Sub-Hue and Sub-Color Adjustment....... 27
4-4. PIP Sub-Contrast Adjustment.............................................. 27
4-5. PIP Sub-Hue, Sub-Color Adjustment................................... 28
4-6. User Control Bar Graph Display Position Adjustment.......... 28
4-7. PIP Position Adjustment ...................................................... 28
5. Diagrams
5-1. Circuit Boards Location ....................................................... 29
5-2. PWB and Schematic Diagrams Information ........................ 29
5-3. Block Diagrams.................................................................... 31
5-4. Frame Schematic Diagram .................................................. 39
Schematics and Supporting Information
A Board................................................................................ 40
G Board ............................................................................... 45
CG Board............................................................................. 47
CB Board ............................................................................. 48
CR Board............................................................................. 49
S Board................................................................................ 50
HA Board ............................................................................. 50
HB Board ............................................................................. 51
HC Board............................................................................. 51
5-5. Semiconductors................................................................... 52
6. Exploded Views
6-1. Cover (KP-43T90)................................................................ 54
6-2. Chassis (KP-43T90) ............................................................ 55
6-3. Picture Tube (KP-43T90) ..................................................... 56
6-4. Cover (KP-48V90) ............................................................... 57
6-5. Chassis (KP-48V90) ............................................................ 58
6-6. Picture Tube (KP-48V90) ..................................................... 59
6-7. Cover (KP-53V90) ............................................................... 60
6-8. Chassis (KP-53V90) ............................................................ 61
6-9. Picture Tube (KP-53V90) ..................................................... 62
6-10. Cover (KP-61V90) ............................................................... 63
6-11. Chassis (KP-61V90) ............................................................ 64
6-12. Picture Tube (KP-61V90) ..................................................... 65
7. Electrical Parts List ........................................................................ 66

—3 —
KP- 43T90 / 48V90 / 53V90 / 61V90
120V AC, 60Hz
170W
1 W
Video 1 IN
Video 2 INPUT (front)
Video 3 IN
S Video IN (4-pin mini DIN)
Y: 1 Vp-p 75 ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms,
Video (phono jack)
1.0 Vp-p, 75 ohms, sync negative;
Audio (phono jacks)
500 mVrms (100% modulation), Impedance: 47 kilohms
Television system
American TV standard
Channel coverage
VHF: 2-13/ VHF: 14-69/ CATV: 1-125
Picture tube
7-inch high-brightness monochrome tubes (6.3 raster size),
with optical coupling and liquid cooling system.
Screen size (measured diagonally)
43 inches (KP-43T90)
48 inches (KP-48V90)
53 inches (KP-53V90)
61 inches (KP-61V90)
SPECIFICATIONS
Design and specifications are subject to change without notice.
Power Requirements
Power Consumption (W)
In Use (Max)
In Standby
Inputs/Outputs
Antenna
75 ohm external terminal for VHF/UHF
Supplied Accessories
Remote Control RM-Y906
Batteries (2) size AA (R6)
Optional Accessories
Connecting Cables
RK-G34, RK-74A, RK-G69HG, VMC-10HG, VMC-720M,
VMC-810S/820S, YC-15V/30V
U/V mixer EAC-66
Video 4 IN
Y: 1 Vp-p, 75 ohms, sync negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
Audio (phono jacks)
500 mVrms (100% modulation), Impedance: 47 kilohms
Audio (VAR/FIX) Out (phono jacks)
500 mVrms (100% modulation), Impedance: 470 ohms
Control S Out
minijack
KP-43T90 KP-48V90 KP-53V90 KP-61V90
100 mm (4 in) 100 mm (4 in) 100 mm (4 in) 160 mm (6
7/8
in)
66 mm (2
5/8
in)
17W x 2 17W x 2 17W x 2 17W x 2
965 x 1058 x 570 mm 1,105 x 1,338 x 579 mm 1,216 x 1,417 x 632 mm 1,370 x 1,560 x 670 mm
38 x 41
5/8
x 22
1/2
in 43
1/2
x 52
5/8
x 22
3/4
in 47
7/8
x 55
3/4
x 24
7/8
in 54 x 61
3/8
x 26
3/8
in
53.2 kg 64.4 kg 66 kg 92.6 kg
117 lbs 142 lbs 145 lbs 204 lbs 8 oz
Speaker Woofer (2)
Tweeter (2)
Speaker Output (W)
Dimensions (W x H x D)
mm
in
Mass kg
lbs

—4 —
KP- 43T90 / 48V90 / 53V90 / 61V90
WARNINGS AND CAUTIONS
CAUTION
Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield, or carbon painted on the CRT, after
removing the anode.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of
this receiver is directly connected to the ac power line.
! SAFETY-RELATED COMPONENT WARNING!!
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for
safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements
published by Sony.Circuit adjustments that are critical for safe operation are identified in this manual. Follow these procedures
whenever critical components are replaced or improper operation is suspected.
ATTENTION!!
Apres avoir deconnecte le cap de l’anode, court-circuiter l’anode du tube cathodique et celui de l’anode du cap au chassis metallique
de l’appareil, ou la couche de carbone peinte sur le tube cathodique ou au blindage du tube cathodique.
Afin d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisélors de tout
dépannage. Le chássis de ce récepteur est directement raccordéàl’alimentation du secteur.
! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identifies par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de
pieces sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont
le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony.Les reglages de circuit dont
l’importance est critique pour la securite du fonctionnement sont identifies dans le present manuel. Suivre ces procedures lors de
chaque remplacement de composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.

—5 —
KP- 43T90 / 48V90 / 53V90 / 61V90
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”or
touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values. Make sure
your instruments are accurate; be suspicious of your HV meter if sets
always have low HV.
8. Check the antenna terminals, metal trim, “metallized”knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage
as described below.
Leakage Test
The AC leakage from any exposed metal part to earth ground and from
all exposed metal parts to any exposed metal part having a return to
chassis, must not exceed 0.5 mA (500 microamperes). Leakage current
can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’instructions to use these
instructions.
2. A battery-operated AC milliammeter. The Data Precision 245 digital
multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit”indication is 0.75 V,
so analog meters must have an accurate low voltage scale. The
Simpson’s 250 and Sanwa SH-63TRD are examples of passive
VOMs that are suitable. Nearly all battery-operated digital multimeters
that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate retaining
screw on most AC outlet boxes is also at earth ground. If the retaining
screw is to be used as your earth ground, verify that it is at ground
by measuring the resistance between it and a cold-water pipe with an
ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble-
light (not a neon lamp) between the hot side of the receptacle and the
retaining screw. Try both slots, if necessary, to locate the hot side on the
line; the lamp should light at normal brilliance if the screw is at ground
potential (see Figure B).
Trouble Light
AC Outlet Box Ohmmeter
Cold-water Pip
e
Figure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.
To Exposed Metal
Parts on Set
AC Voltmeter
(0.75 V)
Earth Ground
0
.15 µF1.5 kΩ

—6 —
KP- 43T90 / 48V90 / 53V90 / 61V90
SELF-DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to flash. The number
of times the LED flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER LED flash indicators is listed in the
instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be used to review
the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
Diagnostic Test Indicators
When an error occurs, the STANDBY/TIMER LED will flash a set number of times to indicate the possible cause of the problem. If there is more than
one error, the LED will identify the first of the problem areas.
Results for all of the following diagnostic items are displayed on screen. If the screen displays a “0”, no error has occurred.
Diagnostic Item STANDBY/ Possible Problem Location Condition Detected Symptoms
TIMER
flashes
Self Diagnosis
Supported model
FRONT PANEL
TIMER/STANDBY indicator
Lamp OFF :
3.0 seconds
Lamp ON : 0.3 seconds
Lamp OFF : 0.3 seconds
• EXAMPLE
Diagnosis Items Number of Blinks
+B overcurrent 2 times
+B overvoltage 3 times
Vertical deflection stop 4 times
TV/VIDEO FLASH FOCUS
VOLUME
POWER TIMER/STAND BY
–+CHANNEL–+
*One blink is not used for self-diagnosis.
Power not On 0 [Standby Power Supply System] Cannot turn on the power
F601 open LED doesn’t blink
R607 open
Q601 short circuit
[Main Power Supply System}
IC601 and R612 are broken
VDR601 short-circuit
+B OCP Detection 2 times Short circuit of power supply in each circuit Goes to the standby mode 2: +B OCP 000
Short circuit of the +B line
+B OVP Detection 3 times T603 pin 7 to pin 8 is open Goes to the standby mode 3: +B OVP 000
Vertical Deflection Stop 4 times IC 1509 (V OUT) is broken Raster goes to one line horizontally 4: V Stop 000
Q1505 (V Pulse Buffer) is broken A and then video signal is muted.
Video Out Abnormality 5 times Video Out, Q705, 732, 761, and others in C board STANDBY/TIMER LED blinks approx. 5: AKB 000
Detection 30 secs, then blinks for the diagnosis
Horizontal Deflection Stop 6 times C515, 516 open. IC206 (YC Jungle) is broken. Raster does not appear. 6: H Stop 000
Audio Abnormality 8 times IC 406 (Audio amp.) is broken. The sound is not out. 8: Audio 000
Detection PS401, 402 open Goes to the standby mode
Note: 000 the range of values for number of operations is 000 - 255. For 256 or higher, the number remains as 255.
Display of Standby/Timer LED Flash Count
Release of TIMER/STANDBY indicator blinking.
The TIMER/STANDBY indicator blinking display is released by turning OFF the power switch on the TV main unit or removing the plug from the
power.

—7 —
KP- 43T90 / 48V90 / 53V90 / 61V90
Self-diagnosis screen displays
In cases of malfunctions where it is not possible to determine the symptom such as when the power goes off occasionally or when the screen
disappears occasionally, there is a screen display on whether the malfunction occurred or not in the past (and whether the detection circuit operated
or not) in order to allow confirmation.
Screen Display Method
Quickly press the remote command button in the following order from the standby state.
Display Channel 5Sound Volume* _Power ON
*Note that this differs from entering the service mode (sound volume +)
Self-Diagnosis Screen Display
The results display is not automatically cleared. In case of repairs and after repairs, check the self-diagnosis screen and be sure to
return the results display to “0 ”.
If the results display is not returned to “0 ”it will not be possible to judge a new malfunction after completing repairs.
Method of Clearing Results Display
1. Power off (Set to the stanby mode.)
2. Display Channel 5Sound Volume +Power ON (Service Mode)
3. Channel 8ENTER (Test reset = Factory preset condition)
Method of Ending Self Diagnosis Screen
When ending the self-diagnosis screen completely, turn the power switch OFF on the remote commander or the main unit.
2: +B OCP 000
SELF DIAGNOSIS
2: +B OCP 000
3: +B OVP 000
4: VSTOP 000
5: AKB 000
101: WDT 000
Results
Diagnosis
000 the range of values for number of
operations is 000-225.
For 256 or higher, the number remains
at 255.

—8 —
KP- 43T90 / 48V90 / 53V90 / 61V90
Self-diagnosis function operation
OCP Low B and +B line detect DET SHORT, and shut-down POWER ON RELAY.
Reset by turning power on/off.
In case of +B is loaded approx. 1.3A or more, microcomputer detects it via IC651.
OVP In case of +B becomes approx. 150V or more, POWER ON RELAY shuts down and microcomputer detects it via IC651.
Reset by turning power on/off just the same as OCP.
V Stop In case of microcomputer detects 2 seconds or more interval of V Pulse, Reference Pulse turns off by turning off the picture
signal in YC Jungle IC (IC206).
After the picture signal turns off, V Pulse is regenerated 2 seconds or more, the picture signal turns on.
AKB IK detection. Makes LED blinking in case of microcomputer doesn’t detect IK returns of IC206 CXA2147Q 30 seconds or more.
H Stop In case of HV becomes 33kV or more, IC502 detects it and shut-down H Drive Pulse.
Microcomputer receives H Stop data from IC206 and makes LED blinking.
Audio In case of DC component overlaps the output of Audio Amp., microcomputer detects it and makes LED blinking.
Microcomputer forces to shut down the power.
Self-diagnosis block diagram
55
8
20 21 22
49
47
50
3
27
34
35
43
5. AKB
5. AKB
3. OVP
2. OCP
4. V.STOP (V Pulse)
Audio
IC002
mProcessor
IC206
CXA2147
YCJ
Q006
D1201
TIMER/STANDBY
IC004
EEPROM
IC502
HV Detector
Q1505
V Pulse Buffer
IC651
OVP Buffer
OCP Buffer
C Board
DC Detect
IC1509
V Drive
IC406
Audio AMP
6. H STOP
6. HV STOP
BUS
4
48
OVP DETECT
OCP DETECT

—9 —
KP- 43T90 / 48V90 / 53V90 / 61V90
Eight Screws (KP-43T90)
Ten Screws (KP-48V90/53V90/61V90)
Rear oard
2
1
1-1. REAR BOARD REMOVAL 1-2. CHASSIS ASSEMBLY REMOVAL
SECTION 1: DISASSEMBLY
From CG oard CN1304.
(The extension ca le is not
supplied ecause of the
countermeasure for radiation.)
G oard
CN203
A oard
Covers
Remove covers from chassis assem ly
with pliers when checking printed circuit oards.
After checking, turn the covers over
and re-secure them with the screws.
Screws
(+BVTP3x12)
Chassis assem ly
Disconnect CN203
on A oard.
1
2
Three screws
(Screw(4x20),tapping)
Chassis assy
2
1
1-3. SERVICE POSITION

—10 —
KP- 43T90 / 48V90 / 53V90 / 61V90
Four screws
(+BVTP 3x12)
Three screws
(+BVTP 3x12)
Four screws
(Screws (4x20), tapping)
HB oard
Control Panel Assem ly HA oard
HA racket
2
4
1
8
Four screws
(+BVTP 3x12)
7
5
6
3
1-5. HA AND HB BOARD REMOVAL
(KP-43T90 ONLY)
1-4. HA AND HB BOARD REMOVAL
(EXCEPT KP-43T90)
Four screws
(+BVTP 4x12)
Four screws
(+BVTP 4x12)
Two screws
(Screws (4x20), tapping)
HB racket
Speaker grille assy
HA oard
HA racket
Multi utton
6
7Three screws
(+BVTP 3x12)
8
HB oard
9
1
5
4
3
2
Three screws
(KP-43T90/48V90)
Five screws
(KP-53V90/61V90)
(Screws (4x20), tapping)
Eleven screws (KP-43T90)
Twelve screws (KP-48V90)
Fifteen screws (KP-53V90)
Fourteen screws (KP-61V90)
(Screws (4x20), tapping)
Beznet assy
2
3
1
1-6. BEZNET ASSY REMOVAL

—11 —
KP- 43T90 / 48V90 / 53V90 / 61V90
HC oard
L screen
holder
Claws
S oard
Sensor
racket (B)
Two screws
(+BVTP 4x12)
Two screws
(+BVTP 4x12)
Two screws
(+BVTP 4x12)
Sensor
racket (A)
7
6
4
1
2
3
5
1-8. HC BOARD AND S BOARD REMOVAL
1-9. A BOARD AND G BOARD REMOVAL
Two screws
(+BVTP 3x12)
Eight screws
(+BVTP 3x12)
G oard
A oard
Terminal oard
Claw
Claws
Main racket
Two screws
(Screws (4x20), tapping)
Seven screws
(+BVTP 3x12)
6
4
9
7
3
2
1
5
8
Seventeen screws (KP-43T90)
Twenty-four screws (KP-48V90)
Twenty-one screws (KP-53V90)
Twenty-five screws (KP-61V90)
(Screw (4x20), tapping)
Mirror cover
1
2
1-7. MIRROR COVER REMOVAL

—12 —
KP- 43T90 / 48V90 / 53V90 / 61V90
1-10. HIGH-VOLTAGE CABLE INSTALLATION AND REMOVAL
1-11. PICTURE TUBE REMOVAL
CAUTION: Removing the arrow-marked screws is strictly prohibited. If removed, it may cause liquid to spill.
(2) Installation
Gutter
HV ca le
Hook 1
Ru er cap
HV ca le
turn 90
1
2
(1) Removal
Four screws
(Screw(4x20), tapping)
Four screws
(+BVTP 4x12)
Picture tu e
Picture tu e
Deflection yoke
Four screws
(Screw(4x20), tapping)
Four screws
(Screw(4x20), tapping)
Neck assy
CR oard
Lens
Lens
2
1
6
7
8
9
11
5
4
3

— 13 —
KP- 43T90 / 48V90 / 53V90 / 61V90
SECTION 2: SET-UP ADJUSTMENTS
2-1. SCREEN VOLTAGE ADJUSTMENT
(COARSE ADJUSTMENT)
1. Select a video input with no signal applied (the screen must be black,
and the room must be as dark as possible. You may use a heavy
blanket over the screen to block out ambient light).
2. Select picture mode “Personal 1” or “Personal 2”, and set
BRIGHTNESS to 50% and PICTURE to minimum.
3. Turn the green SCREEN control on the focus block all the way to
the left and then gradually turn it to the right until the retrace line is
barely visible.
4. Gradually turn the control to the left until the retrace line just
disappears.
5. Repeat steps 1 through 4 for the red and blue CRTs.
R G B
SCREEN
R G B
FOCUS
FOCUS block
2-2.SCREEN (G2) ADJUSTMENT
(FINE ADJUSTMENT)
If the jig described below is available, it is recommended that the G2 Fine
Mode Adjustment be performed to set the screen controls to their optimal
condition. If desired, you can build the jig illustrated below, using 3-watt
resistors. Please note that if the proper voltage is not obtained with the
listed resistor’s values, then increase or decrease one of the values in
the resistor network to obtain the correct voltage.
1. Select VIDEO-1 mode no signal applied (the screen must be black).
2. Connect the G2 JIG.
3. Switch on the JIG.
4. Connect an oscilloscope to the TP701(KR), TP732(KG) and
TP761(KB) of CR board, CG board and CB board.
5. Adjust red, green, and blue screen voltage to 168-172V with SCREEN
controls on the focus block, as shown below.
170V +/- 2V
G2 JIG
200V GND
3.3k 5.6k 5.6k 5.6k
SW
K
GND
pedestal level
2-3. DEFLECTION YOKE TILT ADJUSTMENT
1. Display a cross-hatch pattern
2. Enter the service mode.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
4. Loosen the green CRT’s deflection yoke set screw and align the tilt
of the deflection yoke so that the horizontal bars at the center of
the cross-hatch pattern are parallel to the top and bottom edges of
the screen.
5. After aligning the deflection yoke fasten it securely, making sure it is
fully forward on the neck of the CRT.
6. The tilt of the deflection yoke for red and blue are aligned the same
way as the green CRT.
Cover the green and blue CRT lenses with lens caps (or use the
method shown in the note below for turning off the CRTs individually
without using lens caps), then repeat steps 4 and 5 for the red CRT.
Cover the green and red CRT lenses with lens caps (or use the
method shown in the note below for turning off the CRTs individually
without using lens caps), then repeat steps 4 and 5 for the blue CRT.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from “1”
to “0” in category VPNT, item 28 RON (red), item 29 GON (green), or
item 30 BON (blue).
2-pole magnet
4
-po
l
e magnet
Deflection yoke
Anode cap

—14 —
KP- 43T90 / 48V90 / 53V90 / 61V90
2-4. FOCUS LENS ADJUSTMENT
In this adjustment, use the remote commander while in service mode.
For details on the usage of the service mode and the remote
commander, please refer the item 2-9. ELECTRICAL ADJUSTMENTS
BY REMOTE COMMANDER.
1. Loosen the lens wing nut.
2. Enter the service mode.
3. Display a white raster.
4. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
5. Select adjustment category “PJE”, then press 6 to display the test
signal (crosshatch)*.
* Every time 6 is pressed, the test signal changes to: “crosshatch+video
signal”→“dots+video signal”→“crosshatch only”→“dots only”→black
screen →“crosshatch+video signal”→….etc.
6. Rotate the green lens assembly to adjust to the optimum focus point
with the test signal being displayed
7. Tighten the lens wing nut.
8. Cover the green and blue CRT lenses with the lens caps to allow only
red to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
9. Make sure the cross-hatch is still being displayed; if not, follow step
5 above.
10. Adjust the red CRT lens the same way as the green CRT lens.
11. Cover the green and red CRT lenses with the lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
Test Signal
12. Make sure the cross-hatch is still being displayed; if not, follow step
# 5 above.
13. Adjust the blue CRT lens the same way as the green and red CRT
lenses.
14. After adjusting the items 2-5 “Focus VR Adjustment”, 2-6 “2-Pole
Magnet Adjustment”and 2-7 “4-Pole Magnet Adjustment”, reconfirm
the optimum focus point and adjust again if necessary.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from “1”
to “0”in category VPNT, item 28 RON (red), item 29 GON (green), or
item 30 BON (blue).
2-5. FOCUS CONTROL ADJUSTMENT
1. Enter the service mode.
2. Display a white raster.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
4. Select adjustment category “PJE”, then press 6 to display the test
signal (crosshatch)*.
* Every time 6 is pressed, the test signal changes to: “crosshatch+video
signal”→“dots+video signal”→“crosshatch only”→“dots only”→black
screen →“crosshatch+video signal”→….etc.
5. Adjust the green focus control on the focus block to achieve the
optimum focus point with the test signal being displayed.
6. Cover the green and blue picture lenses with lens caps to allow only
red to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
7. Make sure the cross-hatch is still being displayed; if not, follow step
4 above.
8. Adjust the red focus control on the focus block to achieve the optimum
focus point with the test signal being displayed.
9. Cover the green and red picture lenses with lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
10. Make sure the cross-hatch is still being displayed; if not, follow step
# 4 above.
11. Adjust the blue focus control on the focus block to achieve the
optimum focus point with the test signal being displayed.
12. Repeat steps 1 through 11 after adjusting items 2-4. “Focus Lens
Adjustment”, 2-6 “2-pole Magnet Adjustment”, 2-7 “4-Pole Magnet
Adjustment”
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from “`”
to “0”in category VPNT, item 28 RON (red), item 29 GON (green), or
item 30 BON (blue).
.
A
B
Lens
Minimize both A and B.
Center of crosshatch
Scanning line visible.

—15 —
KP- 43T90 / 48V90 / 53V90 / 61V90
2-6. 2-POLE MAGNET ADJUSTMENT
(GREEN, RED)
1. Display a dot pattern (see the details of using the internal test
patterns at the end of the previous section).
2. Enter the service mode.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
4. Turn the green focus control on the focus block to the right and set it
to overfocus to enlarge the spot (the dot). See figure at the end of
Section 2-3 for the location of the 2-pole magnet adjusting tabs.
5. Adjust the green CRT’s 2-pole magnet so that the small bright spot is
in the center of the large defocused spot.
6. Adjust the green focus control on the focus block and set it for the
best focus.
7. Repeat steps 1 through 6 for the red CRT, except now you will
cover the green and blue CRT lenses with lens caps to allow
only red to show (or use the method shown in the note below
for turning off the CRTs individually without using lens caps) and you
will adjust the red focus control on the focus block.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from “1”
to “0”in category VPNT, item 28 RON (red), item 29 GON (green), or
item 30 BON (blue).
Use the center dot
Large de-focused spot
Small focused spot
2-7. 4-POLE MAGNET ADJUSTMENT
(GREEN, RED, BLUE)
1. Display a dot pattern (see the details of using the internal test
patterns at the end of section 2-5, item 4).
2. Enter the service mode.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
4. Turn the green focus control on the focus block to the left and set it to
under-focus to enlarge the spot.
5. Adjust the 4-pole magnet so that the enlarged spot in the center of the
screen becomes a perfect circle.
6. Adjust the green focus control on the focus block and set it for the best
focus.
7. Repeat steps 1 through 6 for the red CRT, except now you will
cover the green and blue CRT lenses with lens caps to allow
only red to show (or use the method shown in the note below
for turning off the CRTs individually without using lens caps) and you
will adjust the red focus control on the focus block.
8. Repeat steps 1 through 6 for the blue CRT, except now cover the
green and red CRT lenses with lens caps to allow only blue to show.
Adjust the blue focus control on the focus block (or use the method
shown in the note below for turning off the CRTs individually without
using lens caps). However, for the blue CRT do not make the
enlarged spot a perfect circle as indicated in step 5; instead, adjust
the 4-pole magnet so that the height of the enlarged blue spot in the
center of the screen is approx. 1.5 times the width of the spot.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from “1”
to “0”in category VPNT, item 28 RON (red), item 29 GON (green), or
item 30 BON (blue).
.
x
y
x : y = 1:1.5 (BIue)
x : y = 1:1 (Green, Red)
Use the center dot
2-8. DEFOCUS ADJUSTMENT (BLUE)
Note: Adjust the blue dot to be slightly larger than red and green dots.
This adjustment provides a more pleasing picture to the customer.
1. Select the video menu and set the picture mode to “VIVID”.
2. Enter service mode.
3. Change TV mode to the video-1 input mode.
4. Select adjustment category “PJE”, and press 6 as many times as
necessary to display the dot pattern on the screen.
5. Adjust the blue focus control on the focus block to adjust the diameter
of the dots in the center of the screen as shown in the figure below.
FOCUS ADJUSTMENT POINT:
Dmm Max
Screen Size
Diameter
43"
6mm
53"
8mm
61"
9mm

—16 —
KP- 43T90 / 48V90 / 53V90 / 61V90
2-9. ELECTRICAL ADJUSTMENTS BY
REMOTE COMMANDER.
By using Remote Commander RM-Y906), all circuit adjustments can
be made.
NOTE : The following test equipment is required:
1. Pattern Generator with RF, composite, and component outputs)
2. Digital multimeter
2-9-1. METHOD OF ENTERING THE SERVICE
ADJUSTMENT MODE
SERVICE MODE PROCEDURE
1. TV must be in Standby mode. Power off)
2. Press “DISPLAY”, 5, “Volume +”, then “TV Power” on the Remote
Commander.
Press each button within 1 second of pressing the previous button.)
SERVICE MODE ADJUSTMENT
Category Adjustment item
DATA
SCREEN DISPLAY
)
SERVICE VPNT VPOS 031
000000 00
3. The screen displays the adjustment category and the item being
adjusted within that category.
4. Press 1 or 4 to select the adjustment item
5. Press 3 or 6 to change the data
6. Press 2 or 5 to select the adjustment category
7. If you want to go back to the most recently saved value, press “0” then
“ENTER” to read the memory.
8. Press “MUTING” then “ENTER” to write the new adjustment data into
memory.
9. Turn power off when you want to exit the service mode.
Note: Press “8” then “ENTER” to restore the factory settings for user
controls and channel memories this will also turn set off and then on
to exit the service mode).
2-9-2. MEMORY WRITE CONFIRMATION
METHOD
1. After adjustment, remove the plug from the AC outlet, and then
replace the plug in the AC outlet again.
2. Turn the power switch ON and enter the Service Mode.
3. Cycle through the adjusted items again and confi rm that the
adjustments were saved.
2-9-3. ADJUSTING BUTTONS AND
INDICATOR
Note: When the PJE mode which displays an internally generated
signal) is activated, several buttons on the remote commander will have
different functions than the ones listed above. Therefore, when in the PJE
mode, refer to section 2-10 for button functions.
ENTER
Adjustment
item up
Adjustment
item down
TV Power ON
Display
Data up
Data down
Category down
MUTING
Category up
RM-Y906

— 17 —
KP- 43T90 / 48V90 / 53V90 / 61V90
2-9-4. SERVICE MODE LISTS
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0SOPV36-0 (24) NOITISOPV
1ZISV36-0 (30) EZISV
2 MOCV 3-0 0 PMOCV
3 NILV 51-0 (10) YTIRAENILV
4 OCSV 51-0 NOITCERROCEVRUCSV
5 SOPH 51-0 NOITISOPH
6ZISH36-0 (26) EZISH
PMAP36-0 (20) PMANIP
8NIPU51-0() NOITROTSIDNIPRENROCREPPU
9NIPL51-0NOITROTSIDNIPRENROCREWOL
01AHPP51-0ESAHPNIP
11 CFA 3-0 2 NIAGPOOLCFA
21 WOBV 51-0 WOBV
31 GNAV 51-0 ELGNAV
41 FER 3-0 3 NOITISOPESLUPECNEREFER
51VRDR36-0 (31) NIAGEVIRDDER
61VRDB36-0 (31) NIAGEVIRDEULB
1TUCR51-0() FFOTUCDER
81TUCB51-0() FFOTUCEULB
91NOCS51-0() TSARTNOCBUS
02EUHS51-0 (9) EUHBUS
12LOCS51-0 (9) ROLOCBUS
22 2MDC 1,0 0 2EDOMNWODTNUOC
32 XIPD 1,0 1 ERUTCIPCIMANYD
42 CTON 1,0 0 PARTAMORHCY
52 MORC 51-0 0FPARTAMORHC
62 TOT 1,0 0 RETLIFTOTAMORHC
2FPHS3-02 0FSSENPRAHS
82NOR1,01 NODER
92NOG1,01 NONEERG
03NOB1,01 NOEULB
13LOCD1,01 ROLOCCIMANYD
23 DMDC 1,0 0 NWODTNUOCV
33 KLBL 51-0 31 HTDIWKNALBEDIS-TFEL
43 KLBR 51-0 31 HTDIWKNALBEDIS-THGIR
53 CERP 3-0 1 NIV.PMOCROFLEVELREVOERP
63 YERP 3-0 1 NIYROFLEVELREVOERP
( )
( )
( )= PREWRITE DATA
VARIABLE
VARIABLE
FIXED
VARIABLE
FIXED
FIXED
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
FIXED
FIXED
FIXED
FIXED
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
ADJUSTM'T
SETTING
FIXED
FIXED
FIXED
FIXED
FIXED
VPNV (Video Processor NTSC Vivid)
VPNS (Video Processor NTSC Standard)
VPNT (Video Processor NTSC)
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0VRBS36-0 (35) DIVIVROFSSENTHGIRBBUS
1 VMMG 3-0 2 DIVIVROFLEVELAMMAG
2VCDY1,01 DIVIVROFOITARREFSNARTCD-Y
3 VLBA 1,0 1 DIVIVROFEDOMLBA
4VIXA1,00 DIVIVROFY-G,Y-RSIXA
( ) = PREWRITE DATA
ADJUSTM'T
SETTING
VARIABLE
FIXED
FIXED
FIXED
FIXED
SMETI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNAT
ATAD SERVICE DATA NAME
0SRBS36-0DRADNATSROFSSENTHGIRBBUS
1 SMMG 3-0 0 DRADNATSROFLEVELAMMAG
2SCDY1,00 DRADNATSROFOITARREFSNARTCD-Y
3 SLBA 1,0 1 DRADNATSROFEDOMLBA
4SIXA1,00 DRADNATSROFY-G,Y-RSIXA
43T (29), 48V (23)
53V (30), 61V (2 )
( ) = PREWRITE DATA
ADJUSTM'T
SETTING
VARIABLE
FIXED
FIXED
FIXED
FIXED

—18 —
KP- 43T90 / 48V90 / 53V90 / 61V90
PJED (Projection TV Engine)
ID (Identification)
CCD (Closed Caption Decoder)
OP (Option)
ADJUSTM'T
SETTING
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 SIDF 1,0 0 JDAENIFFOYALPSIDATADIGERTCELES
1 HDSO 552-1 23 NOITISOPHUNEMECIVRESDEJP
2 VDSO 552-1 52 NOITISOPVUNEMECIVRESDEJP
3 TSVF 552-0 92 TRATSTSUJDAENIFFOREBMUNENIL
4 TS1V 552-0 0 ATADTRATS1V
5 UC1V 552-0 26 ATADPUTNUOC1V
6PHOC552-00 JDAHGUORFOESAHP-H
PHIF552-0491JDAENIFFOESAHP-H
8PHPT552-016NRETTAPTSETFOESAHP-H
9PHFD552-0522SUCOFCIMANYDFOESAHP-H
01GHFD21-821-08-SUCOFCIMANYDFONIAG2-H
11 GVFD 21-821- 30- SUCOFCIMANYDFONIAG2-V
21 lMWP 552-0 0 lMWP
31 2MWP 552-0 03 NRETTAPTSETIGEROTUAFOESAHP-H
41 DLBH 552-0 832 ENILVEULBDENRUTERFOESAHP-H
51 WLBH 36-0 32 ENILVEULBDENRUTERFOHTDIWESLUP
61PKLB552-02ESLUPKNALBTRATS
1VGOC21-821-IGEROTUAFOATADTESFFOTNECVNEERG
81VROC21-821-IGEROTUAFOATADTESFFOTNECVDER
91VBOC21-821-0 IGEROTUAFOATADTESFFOTNECVEULB
02HGOC21-821- 0IGEROTUAFOATADTESFFOTNECHNEERG
12 HROC 21-821- 0IGEROTUAFOATADTESFFOTNECHDER
22 HBOC 21-821- 0 IGEROTUAFOATADTESFFOTNECHEULB
32 VGOS 21-821- 0
IGEROTUAFOATADTESFFOWEKSVNEERG
42 VROS 21-821- 0IGEROTUAFOATADTESFFOWEKSVDER
52 VBOS 21-821- 0 IGEROTUAFOATADTESFFOWEKSVEULB
62HGOS21-821-0
IGEROTUAFOATADTESFFOWEKSHNEERG
2HROS21-821-0 IGEROTUAFOATADTESFFOWEKSHDER
82HBOS21-821-0 IGEROTUAFOATADTESFFOWEKSHEULB
92RREDEXIF0 EDOCRORREIGEROTUA
03MTDA552-0441IGEROTUAFOATADD/ATEGOTGNIMIT
13 PUV 552-1 1 NOITISOPVREPPUNRETTAPIGEROTUA
23 DIMV 552-1 401 NOITISOPVELDDIMNRETTAPIGEROTUA
33 WOLV 552-1 802 NOITISOPVREWOLNRETTAPIGEROTUA
43 RPH 015-1 1 NOITISOPHNRETTAPIGEROTUA
NRG
TNEC115-215-0)00/00(0 TNECV/HNEERG
WEKS115-215-0)00/00(0 WEKSV/HNEERG
EZIS115-215-0)02-/05(- EZISV/HNEERG
NIL115-215-)xxx/xxx(NILV/HNEERG
YEK115-215-)xxx/xxx(YEKV/HNEERG
NIP115-215-0)32/xxx(NIPV/HNEERG
ULB
TNEC115-215-0)00/00(0 TNECV/HEULB
WEKS115-215-0)00-/00(0 WEKSV/HEULB
EZIS115-215- (-050/-225) EZISV/HEULB
NIL115-215- (-150/xxx) NILV/HEULB
YEK115-215- (xxx/-100) YEKV/HEULB
NIP115-215- (xxx/200) NIPV/HEULB
DER
TNEC115-215- (000/000) TNECV/HDER
WEKS115-215- (000/000) WEKSV/HDER
EZIS115-215- (-050/-210) EZISV/HDER
NIL115-215- (150/xxx) NILV/HDER
YEK115-215- (xxx/100) YEKV/HDER
NIP115-215- (xxx/225) NIPV/HDER
0
0
( ) = PREWRITE DATA
XXX: CANNOT CHANGE
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
VARIABLE
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 SERS 3-0 1 SERIES ID
1 LPWR 3-0 0 LAST POWER MEMORY
2 LANG 3-0 0 LANGUAGE
ADJUSTM'T
SETTING
FIXED
FIXED
FIXED
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 PHCC 36-0 83 DX/CC&XEDNIISOPHDSO
1NHCC36-092NOITCNUFON
ADJUSTM'T
SETTING
FIXED
FIXED
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 PSID 36-0 (9) NOITISOPHDSO
1lWF-02 WODNIW1DLEIF
22WF-03 WODNIW2DLEIF
3IDXT 2MOTION PERIOD /INDEX
0-255
ADJUSTM'T
SETTING
VARIABLE
FIXED
FIXED
FIXED

—19 —
KP- 43T90 / 48V90 / 53V90 / 61V90
3DCM (3D Comb Filter)
TONE (Tone Control)
DAC (D/A Converter)
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0HSVU36-013EUHBUSVUY
1CSVU36-013ROLOCBUSVUY
ADJUSTM'T
SETTING
FIXED
FIXED
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0DMRN3-00 EDOMRECUDERESION
1OCYD51-02
DGNITTESLEVELGNIROCY
2AGYD51-001DGNITTESNIAGY
3OCCD51-05
DGNITTESLEVELGNIROCC
4AGCD51-05
DGNITTESNIAGC
5DLES1,01 TCELESD RETLIFLANGISY
6 AG2D -0 4 DGNITTESNIAGdn2C/Y
HRTV 3-0 1 GNITTESSISERETSYHCNYSHRTV
8 RRTV 3-0 1 GNITTESECNEREFERCNYSHRTV
9 RSDL 3-0 2 ECNEREFERLANGISDL
01 GPAV -0 5 NIAGERUTREPAV
11IPAV13-011TNIOPTREVNIERUTREPAV
21TFPY3-00 PATRETLIFGNIKAEPY
31GFPY51-09 NIAGRETLIFGNIKAEPY
41SP1V3-02 ROTCELESENIL-1LACITREV
51SGEV3-01 ROTCELESEGDELACITREV
61 N3CC 1,0 0 RETLIFMOCENIL-3LANGISC
1 PDH -0 4 ESAHPLATNOZIROHDH
81 LDC -0 5 YALEDC
91 LSSH 51-0 21 LEVELECILSCNYSH
02 LSSV 51-0 8 LEVELECILSCNYSV
12FLPH1,01 RETLIFLLPH
22FLPB1,00 RETLIFLLPTSRUB
32FCSF1,01 NIAGRETLIFCSF
42GFLP1,01 NIAGRETLIFLLP
52DAXE1,00 NIDALANRETXE
62 SSM 1,0 0 LANGISNOITOMDECROF
2 TUOC 3-0 3 TUPTUOLANGISC
82 SPAY 3-0 1 ERUTREPAY
92 SDSN 3-0 0 .TCETEDLANGISDTSNON
03 PPC 3-0 2 EGNARDA&ESLUPPMALC
13OCHY3-01 GNIROCLANGIS.QERFHGIHY
23RLIK51-03 ECNEREFERRELLIK
33SPGB51-04 NOITISOPTRATSPGB
43WPGB51-001HTDIWPGB
53LCDA3-01 YALEDKCOLCDA
63FRWP1,00 ECNEREFERHTDIWESLUP
3GCHY1,00
N
IAG2/1GNIROCLANGIS.QERFHGIHY
832GKC1,01 TIBTSETROTARENEGKCOLC
93EGKC1,00 TIBTSETROTARENEGKCOLC
40 NSDS 0,1 0 NON STD SIGNAL DETECT
41 SYPD 0,1 0 MEMORY POWER DOWN
42 CNRO 0,1 0 CHROMA NOISE REDUCT TEST BIT
43 YNRK 0,1 0 Y NOISE REDUCT FILTER GAIN
44 YNRI 0,1 0 Y NOISE REDUCT FILTER CONV.
45 YNRL 0-3 1 Y NOISE REDUCT FILTER LIMIT
46 CNRK 0,1 0 CHR. NOISE REDUCT FILTER GAIN
4 CNRI 0,1 0 CHR. NOISE REDUCT FILTER CONV.
48 CNRL 0-3 1 CHROMA NOISE REDUCT LIMIT
49 WSC 0-3 1 NOISE DETECTION CORING
ADJUSTM'T
SETTING
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 SABR 36-0 ATADSSABEULAVTESER
1 ERTR 36-0
61V (35)
ATADELBERTEULAVTESER
2HEBB51-010 YCNEUQERFHGIHEBB
LE-3BB1106 YCNEUQERFWOLEBB
5EFUS 1 TCEFFEDNUORRUS
4 LOOP 1 LOOP EFFECT
Others (31)
61V (39)
Others (31)
ADJUSTM'T
SETTING
FIXED
FIXED
FIXED
FIXED
VARIABLE
VARIABLE

—20 —
KP- 43T90 / 48V90 / 53V90 / 61V90
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DRADNATS
ATAD SERVICE DATA NAME
0 FSEL 0-3 0 FIELD SELECT FIXED
1 VACQ 0-15 2 VERTICAL ACQUISITION VARIABLE
2 HACQ 0-15 4 HORIZONTAL ACQUISITION VARIABLE
3 ISYS 0-3 0 INSET DISPLAY SYSTEM FIXED
4 PSYS 0-3 0 PARENT SYSTEM FIXED
5 FACT 0,1 0 FRAME MODE ACTIVATION FIXED
6 HZM 0- 0 HORIZONTAL ZOOM FIXED
VPNR 0,1 0 V SYNC PULSE NOISE REDUCT FIXED
8 VPDL 0-31 8 VERT SYNC PULSE DELAY FIXED
9 FRSL 0,1 0 FRAME SELECT FIXED
10 FRWH 0- 2 FRAME WIDTH HORIZONTAL FIXED
11 FRWV 0-3 1 FRAME WIDTH VERTICAL FIXED
12 VERB 0,1 0 VERTICAL BLANKING MODE FIXED
13 SELD 0-15 0 SELECT DELAY FIXED
14 PCOR 0,1 1 POSITION CORRECTION FIXED
15 CLDL 0-31 0 CLAMPING DELAY FIXED
16 CLMD 0-3 3 CLAMPING DURATION FIXED
1 CLMS 0-3 2 CLAMPING PULSE START FIXED
18 POFV 0- (1) POS. OFFSET FINE V VAR. VARIABLE
19 POFH 0-31 (2) POS. OFFSET FINE H VAR. VARIABLE
20 VSHK 0-31 0 VERTICAL SHRINK FIXED
21 HSHK 0-31 0 HORIZONTAL SHRINK FIXED
22 CLPL 0-3 0 CLAMPING PULSE LENGTH FIXED
23 REFI 0,1 0 REFRESH INTERVAL FIXED
( ) = PREWRITE DATA
ADJUSTM'T
SETTING
METI
REBMUN
TNEMTSUJDA
METI
ATAD
EGNAR
DTS
ATAD SERVICE DATA NAME
( ) = PREWRITE DATA
0 PSCN 0-15 (8) PIP SUB CONTRAST VARIABLE
1 PSC4 0-15 5 PIP SUB CONTRAST FOR VIDEO 4 FIXED
2 PHUE 0-63 (32) PIP SUB HUE VARIABLE
3 PCOL 0-15 (8) PIP SUB COLOR VARIABLE
4 PCL4 0-15 9 PIP SUB COLOR FOR VIDEO 4 FIXED
5 PBRT 0-15 1 PIP BRIGHTNESS FIXED
6 PBT4 0-15 1 PIP BRIGHTNESS FOR VIDEO 4 FIXED
PYDR 0-255 192 PIP Y DRIVE FIXED
8 PYD4 0-255 192 PIP Y DRIVE FOR VIDEO 4 FIXED
9 PUDR 0-255 180 PIP U DRIVE FIXED
10 PUD4 0-255 180 PIP U DRIVE FOR VIDEO 4 FIXED
11 PVDR 0-255 120 PIP V DRIVE FIXED
12 PVD4 0-255 120 PIP V DRIVE FOR VIDEO 4 FIXED
13 PYPD 0-15 1 PIP Y PEDESTAL FIXED
14 PUPD 0-31 (15) PIP U PEDESTAL VARIABLE
15 PVPD 0-31 (15) PIP V PEDESTAL VARIABLE
16 AGCR 0,1 0 AUTO GAIN CONTROL RESET FIXED
1 AGCM 0-3 3 AUTO GAIN CONTROL MODE FIXED
18 AGCV 0-15 12 AUTO GAIN CONTROL VALUE FIXED
19 AGC4 0-15 12 AUTO GAIN CNTRL FOR VIDEO 4 FIXED
20 LMOF 0-3 3 LUMINANCE OFFSET FIXED
21 PLLI 0-3 0 INSET PLL TIME CONSTANT FIXED
22 NRPL 0-3 0 NOISE REDUCTION INSET PLL FIXED
23 PYDL 0-15 0 PIP Y/C DELAY FIXED
24 CSTD 0- 1 COLOR STANDARD FIXED
25 CEXC 0-3 1 COLOR STANDARD EXCLUSION FIXED
26 LKSP 0,1 0 STANDARD ID SPEED FIXED
2 CKIL 0-3 0 COLOR KILLER THRESHOLD FIXED
28 BGPS 0,1 0 BURST GATE PULSE START POS. FIXED
29 CLON 0,1 0 COLOR ON FIXED
30 ACCF 0,1 0 DISABLE AUTO CHROMA CONTROL FIXED
31 IFFL 0-3 0 IF-COMPENSTATION FILTER FIXED
32 STNR 0,1 0 SATELLITE NOISE REDUCTION FIXED
33 FMAC 0,1 0 FRAME MODE ACTIVATION INSET FIXED
34 CPLL 0,1 0 CHROMA PLL OFF FIXED
35 SCAD 0-31 COLOR SUBCARRIER ADJ. FIXED
36 FRMY 0-15 5 FRAME Y LEVEL FIXED
3 YPEK 0- Y PEAKING ADJUSTMENT FIXED
38 YCOR 0,1 0 Y CORING ENABLE FIXED
39 CHBW 0-3 1 CHROMA BANDWIDTH FIXED
ADJ.
SETTING
PIP (Picture In Picture)
PYC