Spacepro Chest of Drawers and Tallboy User manual

chest of drawers & tall boy
Assembly Instructions
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
Page 1 of 5
12x
One piece
connectors
(16x for Tall Boy)
4x
T-nuts
12x
Plastic dowels
(16x for Tall Boy)
18x
Euro Screws
(24x for Tall Boy)
Chest of drawers & tall boy contents:
A1x Top panel
B 2x Back panels
(1x for Tall Boy)
C 1x Side panel (left)
D 1x Side panel (right)
E1x Base
F4x Legs
G 2x Drawer infills
(3x for Tall Boy)
H 2x Infill covers
(3x for Tall Boy)
I 3x Drawer sides (left)
(4x for Tall Boy)
J3x Drawer sides (right)
(4x for Tall Boy)
K3x Drawer backs
(4x for Tall Boy)
L3x Drawer fronts
(4x for Tall Boy)
M3x Drawer bases
(4x for Tall Boy)
N6x Soft close clips (3x left, 3x right)
(8x for Tall Boy, 4x left, 4x right)
O6x Soft close drawer runners (3x left, 3x right)
(8x for Tall Boy, 4x left, 4x right)
12x
Wood Screws
(16x for Tall Boy)
V1
Chest of drawers
Tall boy
20x
Dowels
(24x for
Tall Boy)
20x
Cams
(24x for Tall Boy)
2x
Wall mounting
brackets
12x
Drawer bottom
support brackets
(Chest of
Drawers only)
We recommend you use the Wall
Mounting Brackets provided to fix
the Chest of Drawers/Tall Boy to
a wall (where possible). This will
prevent the unit being pulled over.
Use suitable fixings.
• Tools: Screwdriver & Hammer
• Two person build
Recommended:

SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
Page 2 of 5
3 4 1 – Insert Cams. 2 – Remove film then attach infill covers.
Repeat on both drawer infills.
Fix the Wall Mounting Brackets with the screw provided in the pack.
12
x6
x6
x6
x4
x4
5
Note: C panel shown
Use hammer to tap T-nuts (2) into place.
x2
x2
Ensure the infills are faced towards the bottom.
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
STEP 1 STEP 2
Bottom
x2

SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
Page 3 of 5
910
Screw through holes shown on both sides.
Note: 6x for Chest of Drawers, 8x for Tall Boy.
x6
x4
x12
Lay unit on its back, then insert legs into
holes and turn until tight.
6 87 Slide back panel (B) in place.
11
x2
x2
Tap plastic dowels (3) gently into place with a hammer
(Repeat on all drawer sides).
SQUEEZE SIDES
THEN INSERT
PIN
Note: Tall Boy back panel
is one complete panel
FIX THROUGH THESE HOLES
Bottom
Bottom Bottom
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.

SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
15
Page 4 of 5
1
2
12 14
13 Repeat on all drawers.
CHEST OF DRAWERS ONLY
PIN
x4 (per drawer)
Push/tap sides (J&I) onto back panel (K).
(Repeat on both drawers).
Drawer back
Repeat on all drawers. (Drawer shown from underneath).
1 – Slide the drawers so that the prong goes into the hole in the back of the drawer.
2 – Pull the sliders forward, until you hear a click, repeat on both sides.
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
x4

SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
We recommend you use
the Wall Mounting Brackets
provided to fix the Chest of
Drawers/Tall Boy to a wall
(where possible). This will
prevent the unit being pulled
over. Use suitable fixings.
WALL MOUNTING
BRACKETS
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
Page 5 of 5
Fix the Wall Mounting Bracket to both sides of the Unit(s).
(Use suitable fixings when attaching to the wall).
USE SUITABLE
WALL FIXINGS