SPARNOD SUB-50 User manual

Page1
Safety Information
Before you undertake any program of exercise that will increase cardiovascular activity please be
sure to consult with your doctor. Frequent strenuous exercise should be approved by your doctor
and proper use of your product is essential. Please read this manual carefully before
commencing assembly of your product or starting to exercise.
* Please keep all children away from exercise products when in use. Do not allow children to
climb on them when they are not in use.
* For your own safety, always ensure that there is at least 1 Meter of free space in all
directions around your product while you are exercising.
* Regularly check to see that all nuts, bolts and fittings are securely tightened. Periodically
checking all moving parts for obvious signs of wear or damage.
* Clean only with a damp cloth, do not use solvent cleaners.
* Before use, always ensure that your product is positioned on a solid, flat surface. If
necessary, use a rubber mat underneath to reduce the possibility of slipping in use.
* Always wear appropriate clothing and footwear such as training shoes when
exercising. Do not wear loose clothing that could become caught or trapped during exercise.
Storage and Use
Your product is intended for use in clean dry conditions. You should avoid storage in
excessively cold or damp places as this may lead to corrosion and other related problems that
are outside our control.
Weight Limit
100 kg maximum
Beginning Exercising
How you begin to exercise will vary from person to person. If you have not exercised for
a long period of time, have been inactive for a while, or are severely overweight youmust
start slowly, increasing your exercise time gradually, by perhaps only a few minutes for each
session per week.
Combine a carefully structured nutritious diet with a simple but effective exercise routine and this
can help make you feel better, look better and will almost certainly enable you to enjoy life more.

Page2
26
21 25
24
EXPLODED VIE
W
1:1

Page3
Par
t
lis
t
1:1
NO . Description QTY NO . Description QTY
01 Main Frame 1
14 Tension Control Knob 1
02 Front Stabilizer 1
15 Inner Hex Bolt(M8X30) 2
03 Rear Stabilizer 1
16 Washer(1/2”) 2
04 Front Post 1
17 Computer 1
05 Handlebar 1
18 Nut 3
06 Seat Post 1
19 Washer 3
07 Seat 1
20 Pedal (L/R) 1set
08 Carriage Bolt (M8X60) 4
21 Lower Sensor Wire 1
09 Curved Washer 8
22 Wire C 1
10 Domed Nut(M8) 4
23 Crank 1
11 Fixing Knob 1
24 Lower Tension Hook
1
12 Inner Hex Bolt (M8x15) 4
25 Upper Tension Cable
1
13 Screw (M5x10)
1 26 Upper Sensor Wire
1

Page4
15
No.8 Qty 4
No.9 Qty 8
No.10 Qty 4
Part lis
t
1:1
No.12 Qty 4
No.13 Qty 1
Cross Wrench
Qty 1
Allen Wrench
Qty1

Page5
A
SSEMBLY INSTRUCTIONS
1:1
1
No.8 Qty 4 No.9 Qty 4 No.10 Qty 4
STEP1.
Attach the Front Stabilizer (2) to the Main Frame (1) using 2pcs of Domed Nuts (10), Curved
Washers (9) and Carriage Bolts (8). The installation of the Rear Stabilizer (3) is same to the
Front Stabilizer (2).

Page6
No.9 Qty 8
No.12 Qty 4
A
SSEMBLY INSTRUCTIONS
1:1
2
25 26
24
21
STEP2.
Connected Lower Tension hook(24) and Upper Tension Cable (25) as picture A.
Connected lower Sensor Wire(21) and Upper Sensor Wire(26) as picture B.
Attach the Front Post (4) to the Main Frame (1) using 4pcs of Inner Hex Bolts
(12) and Curved Washers (9).

Page7
ASSEMBLY INSTRUCTIONS
·
3
No.13 Qty 1
STEP3.
Please first turn the tension to the minimum section “—”. Then fix the Tension
Control Knob (14) to the Front Post (4) with a Screws (13).

Page8
ASSEMBLY INSTRUCTIONS
4
STEP4.
Attach the Handlebar (5) to the Front Post (4) using 2pcs of Inner Hex Bolt (15), 2pcs of
Washer(16),. Then connect the Lower Sensor Wire (21) and Upper Sensor Wire (22).
Insert computer (17) in the computer holder carefully on the Front Post (4).
These two parts need to be in the same side when connect.

Page9
A
SSEMBLY INSTRUCTIONS
1:1
5
STEP5.
Fixing the Seat (7) on Seat Post (6) with 3pcs of Washers (19, and Nut (18) tightly.

Page10
A
SSEMBLY INSTRUCTIONS
1:1
6
STEP6.
Insert the Seat Post (6) into the Main Frame
(1) and line up the holes that give the correct seat height. (This can be done after it has
been assembled.) Secure the seat in position with the Fixing Knob (11).

A
SSEMBLY INSTRUCTIONS
1:1
7
Anti-clockwise
STEP7.
Clockwise
Fixing left pedal (20) on the left side of crank (23), fixing right pedal (20) on the right
side of crank (23), make sure it is tightly.
Page11