Spectra FW V1.6 User manual

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 1
USER MANUA AND IST OF SMS COMMANDS FOR
USER MANUA AND IST OF SMS COMMANDS FOR USER MANUA AND IST OF SMS COMMANDS FOR
USER MANUA AND IST OF SMS COMMANDS FOR
PROGRAMMING THE
PROGRAMMING THEPROGRAMMING THE
PROGRAMMING THE
PIXE
PIXEPIXE
PIXE GPRS/SMS TRACKER DEVICE
GPRS/SMS TRACKER DEVICEGPRS/SMS TRACKER DEVICE
GPRS/SMS TRACKER DEVICE
-
--
- FW V
FW VFW V
FW V1.6
1.61.6
1.6 AND HIGHER
AND HIGHER AND HIGHER
AND HIGHER -
--
-
Issue date: September 2012
Version: 1.2

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 2
INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
This manual illustrates the correct use of the PIXE GPRS/SMS V.1.6 tracker device.
Before starting, please insert a SIM card into the tracker device after first making the following
checks on it:
-The PIN request on the SIM must be disabled.
-All call waiting, transfer and voicemail functions should be deleted.
-The SIM must have sufficient credit to make calls and answer remote diagnostic commands with
SMS messages.
-First check the SIM by using it in a normal mobile phone (make a call, answer a call, send and receive
SMS messages).
-For SIMs with separate numbers for voice, data, fax, use the voice number for sending the
programming text messages.
Closely follow the syntaxes described below to send commands by SMS to the tracker device.
Wait about 20 seconds between one SMS and the next to allow the network to send the commands
correctly and let the tracker device encode and subsequently delete them.
When the SMS arrives, the tracker device will acknowledge the command with a series of flashes to
indicate that the message has been received, interpreted and deleted.
WARNING!
WARNING!WARNING!
WARNING! Improper use of these articles constitutes a violation of Italian Republic aw N° 98 art.615
bis, penal code; art. 226 bis, code of criminal procedure dated 08-04-1974 concerning the
confidentiality of private life and the interception of communications. Under no circumstances can
SPEKTRA s.r.l. be held responsible for the illegal use of these appliances.
Product reliability and high-level performance are ensured by the ongoing evolution of technical
specifications and requirements in synergy with our institutional customers and general protocol
distributors. Please do not hesitate to contact us for any clarifications and/or observations
concerning functioning or possible customization.
Thank you for choosing SPEKTRA s.r.l.

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 3
CONTENTS
CONTENTSCONTENTS
CONTENTS
INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION ____________________________________________
________________________________________________________________________________________
____________________________________________ pag.2
pag.2pag.2
pag.2
SETTING REMOTE NUMBERS
SETTING REMOTE NUMBERSSETTING REMOTE NUMBERS
SETTING REMOTE NUMBERS __________________________________
____________________________________________________________________
__________________________________ pag.4
pag.4pag.4
pag.4
SETTING GEOFENCING AREA
SETTING GEOFENCING AREASETTING GEOFENCING AREA
SETTING GEOFENCING AREA __________________________________
____________________________________________________________________
__________________________________ pag.5
pag.5pag.5
pag.5
TRACKING
TRACKING TRACKING
TRACKING CE
CECE
CE -
--
-ID SMS COMMANDS
ID SMS COMMANDSID SMS COMMANDS
ID SMS COMMANDS ____________________________
________________________________________________________
____________________________ pag.6
pag.6pag.6
pag.6
PROGRAMMING GENERA PARAMETERS
PROGRAMMING GENERA PARAMETERSPROGRAMMING GENERA PARAMETERS
PROGRAMMING GENERA PARAMETERS _________________________
__________________________________________________
_________________________ pag.
pag.pag.
pag.7
77
7
PROGRAMMING PARAMETERS FOR THE GPRS/TCP SECTION
PROGRAMMING PARAMETERS FOR THE GPRS/TCP SECTION PROGRAMMING PARAMETERS FOR THE GPRS/TCP SECTION
PROGRAMMING PARAMETERS FOR THE GPRS/TCP SECTION _________
__________________
_________ pag.
pag.pag.
pag.8
88
8
DIAGNOSTICS OF THE TRACKER DEVICE
DIAGNOSTICS OF THE TRACKER DEVICEDIAGNOSTICS OF THE TRACKER DEVICE
DIAGNOSTICS OF THE TRACKER DEVICE _________________________
__________________________________________________
_________________________ pag.
pag.pag.
pag.9
99
9
GENERA
GENERAGENERA
GENERA NOTES ON THE OPERATION
NOTES ON THE OPERATIONNOTES ON THE OPERATION
NOTES ON THE OPERATION __________________________
____________________________________________________
__________________________ pag.11
pag.11pag.11
pag.11
TECHNICA FEATURES
TECHNICA FEATURESTECHNICA FEATURES
TECHNICA FEATURES ______________________________________
____________________________________________________________________________
______________________________________ pag.
pag.pag.
pag.12
1212
12

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 4
SETTING REMOTE NUMBERS
SETTING REMOTE NUMBERSSETTING REMOTE NUMBERS
SETTING REMOTE NUMBERS
The following commands set the telephone numbers of the recipients, for which enabling the
selected function is required (IT IS ADVISAB E TO ENTER THE INTERNATIONA PREFIX BEFORE THE
SE ECTED NUMBER).
##NGPSAxxx* setting number for continuous VEHIC E OCA ISATION
VEHIC E OCA ISATIONVEHIC E OCA ISATION
VEHIC E OCA ISATION SMS
##NGPSBxxx* setting SECON
SECONSECON
SECOND
DD
D NUMBER
NUMBER NUMBER
NUMBER for continuous VEHIC E OCA ISATION
VEHIC E OCA ISATIONVEHIC E OCA ISATION
VEHIC E OCA ISATION
##NSTARTxxx* setting number for VEHIC E START
VEHIC E STARTVEHIC E START
VEHIC E START SMS
##NSTOPxxx* setting number for VEHIC E STOP
VEHIC E STOPVEHIC E STOP
VEHIC E STOP SMS
##NMU TIxxx* setting number for MU TIP E POSITION
MU TIP E POSITIONMU TIP E POSITION
MU TIP E POSITION SMS
This special SMS contains the complete information of 5 memory points.
Setting the number activates the SMS transmission to the PC with the PIXE -GPRS
software loaded, which will read and decode them via the specific GSM modem.
Transmission is automatic when reaching 5 positions stored by the tracker device,
with a repetition rate defined by the specific storage command.
E.g.: ##TM00010 = Send SMS every 10 sec x 5 points = every 50 seconds
(containing 5 positions).
(See the ##TMxxxxx command on the following page).
xxx = TE EPHONE NUMBER
E.g.: ##N [phone]* - programs the number for transmitting the continuous localisation SMS.
WARNING!
WARNING!WARNING!
WARNING! to disable the function corresponding to one or more of the above-mentioned numbers,
program the number, entering 5 zeros in place of the number itself:
E.g.: ##N 00000* - disables the continuous vehicle localisation SMS.
WARNING!
WARNING!WARNING!
WARNING! always remember to put an asterisk ( * ) at the end of the number being set, even when
entering 5 zeros to deactivate the function.
##TSxxxxx the tracker device sends the continuous localisation SMS messages (if configured)
with a delay of the number of seconds indicated by this parameter
xxxxx = 00005->65530 seconds
xxxxx = 00000 transmission disabled - (DEFAU T)

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 5
SETTING
SETTINGSETTING
SETTING GEOFENCING
GEOFENCINGGEOFENCING
GEOFENCING AREA
AREAAREA
AREA
The following commands set the telephone numbers of the recipients, on which you want to enable the
geofencing areas alarmed.
The management includes both the entry that the output of the vehicle by a preset specific area.
You can program up to 5 local areas.
##NAINxxx* setting number for A
AA
A ERT
ERTERT
ERT AREA IN
AREA INAREA IN
AREA IN sms (vehicle entry in to the area.)
##NAOUTxxx* setting number for A
AA
A ERT
ERTERT
ERT AREA
AREA AREA
AREA OUT
OUTOUT
OUT sms (vehicle exit from the area.)
##AREAn+xx.xxxx+yyy.yyyykkO setting value of area and type (IN / OUT)
In details:
n = identifies the number of area (n = 1->5)
+xx.xxxx = identifies coordinate ATITUDE
+yyy.yyyy = identifiies coordinate ONGITUDE
kk = identifies the radius that applies to the area affected (*View table below)
O = The letter "O" identifies the output (OUT) of the vehicle from the area, with the
letter "I" identifies the input (IN) of the vehicle in to the area.
* Table for selecting preset alarm radius area (expressed in meters)
00 = off area (although other fields are set, the control will not run)
01=20 mt
02=50 mt
03=100 mt
04=200 mt
05=500 mt
06=1 Km
07=2 Km
08=5 Km
09=10 Km
10=20 Km
11=50 Km
12=100 Km
13=200 Km
14=500 Km

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 6
TRACKING CE
TRACKING CETRACKING CE
TRACKING CE -
--
-ID SMS COMMANDS
ID SMS COMMANDSID SMS COMMANDS
ID SMS COMMANDS
This function will enble the continuos send of cell-id sms with specific delay.
Spektra provide a specific localization software with an extension that read this information and, using a
pubblic cell-id database, localize the pixel unit.
To do so is necessary provide an internet connection and a gsm modem connected to the personal
computer that run the application.
All the cell-id data and the localization information will be stored in a specific sql database and may be
reviewed later to analize the route done from the unit.
Please ask us for the full implementation of thi extension and for the software prerequisities.
To enable this functionality you will use the follwing commands:
##NCE xxx* set the cell
cellcell
cell-
--
-id
id id
id tracking number fot the outgoing sms
This number corresponds at the sim inside in the modem connected to the pc.
No the pc will be already installed our software for tracking the unit.
##TCxx the unit sends the continuous localization cell-id sms messages (if configured) with
a delay of minutes indicated in this setting:
xx = 00 functions disable (default)
Xx = 01->99 minutes
##D2 request of cell-id from all the avaiable network company.
WAR
WARWAR
WARNING
NINGNING
NING:
::
: this command may take up to 5 minutes to executed, during this time the
pixel will be not registrered and will be busy.
(at least 9 cell-id will be logged).

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 7
PROGRAMMING GENERA PARAMETERS
PROGRAMMING GENERA PARAMETERSPROGRAMMING GENERA PARAMETERS
PROGRAMMING GENERA PARAMETERS
##NNAMExxxx* setting the unique name of the tracker device
xxxx = vehicle name (maximum 10 characters)
xxxx = VEICO O1 - (DEFAU T)
##MOVx enable the shock sensor and set the motion sensivity
x = 0->9
x = 0 function disable (DEFAU T)
x = 1 low sensivity, a long and durable movment is necessary to trigger the
unit.
x = 9 high sensivity, a little movment is enough to trigger the unit.
##F0 GPS receiver in normal operation, the module is switched on during the vehicle
movement and switched off about one minute after the vehicle stops - (DEFAU T)
##F1 GPS receiver always forced to on (only recommended for internal installations)
## EDx status ED on board on/off
x = 0 ED always off
x = 1 ED normal operation with various diagnostic flashing - (DEFAU T)
##Ixx the tracker device continues to store for the time requested, even if there is no
movement. This command allows the user to modify this value based on their
requirements.
xx = 01->99 minutes
xx = 05 minutes - (DEFAU T)
##TMxxxxx the tracker device stores a GPS point every xxxxx seconds. This command allows
the user to modify this value to adapt it to their requirements.
xxxxx = 00002->65530 seconds
xxxxx = 00005 - (DEFAU T)
##FORMAT clears all user programming and resets the tracker device to the original factory
settings (an immediate hardware reset of the entire tracker device is also
generated)
##RESET the immediate restart of the entire tracker device is forced without modifying the
set configurations
##C EAR-TCP reset the buffer of the memory-points TCP
##C EAR-SMS reset the buffer of the memory-points SMS
##C EAR-A reset the buffers of the memory-points SMS and TCP
##D -TCP force the download of the buffer memory TCP and wakeup the device
##D -SMS force the download of the buffer memory SMS and wakeup the device
##WAKEUP activates the tracker device by simulating a physical movement.

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 8
PROGRAMMING PARAMETERS
PROGRAMMING PARAMETERSPROGRAMMING PARAMETERS
PROGRAMMING PARAMETERS FOR THE GPRS/
FOR THE GPRS/FOR THE GPRS/
FOR THE GPRS/TCP SECTION
TCP SECTIONTCP SECTION
TCP SECTION
##NAPNxxx* manual setting of a generic APN for internet access (after changing the APN, the
tracker device must be restarted with the special ##RESET command, or else by
switching it off then back on again)
xxx = APN name (maximum 50 characters)
xxx= ibox.tim.it - (DEFAU T)
##NAPNUNxxx* setting user name for accessing the APN
xxx = user ID (maximum 20 characters)
##NAPNPWxxx* setting password for accessing the APN
xxx = APN password (maximum 20 characters)
xxx = not set - (DEFAU T)
##NSERVERxxx* setting remote server name with PIXE MU TIVEICO O software installed or its
public IP address
xxx = name of the server or its IP address (maximum 50 characters)
xxx = server_tcp.com - (DEFAU T)
##PORTxxxxx setting the port number of the remote server
xxxxx = 00000 -> 65530
xxxxx = 00260 – (DEFAU T)
##PPxx it defines the number of points that will be packeted in each TCP transmission
xx = 00 function disabled (DEFAU T)
xx = 01 -> 30 transmission points per packet

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 9
DIAGNOST
DIAGNOSTDIAGNOST
DIAGNOSTICS OF THE TRACKER DEVICE
ICS OF THE TRACKER DEVICEICS OF THE TRACKER DEVICE
ICS OF THE TRACKER DEVICE
These commands are sent to the tracker device to identify its status. The tracker device will reply
with SMS messages containing the programmed settings and other operating parameters. (E.g.
antenna signal, number of satellites detected etc.)
The diagnostics SMS messages are sent to the mobile phone number that made the request (the
default values are indicated).
##DA requests all the below-mentioned diagnostics messages
##D1 G-PIXE - V1.6 - D1
-NVOCE:NON PROG.
-NENTR:NON PROG.
-RAN
-ED:1
-VO :3
-DSP:0
-EXTRA:0
-ECHO:0
-MIK:0
-MOV:9
-VOX:0
-ISTERESI:05
-TR:01
-TAV:00
##D2 G-PIXE - V1.6 - D2
-NCE :NON PROG.
-TC:00
##D3 G-PIXE - V1.6 - D3
-NNAME:VEICO O1
-NAPN: ibox.tim.it
-NAPNUN:NON PROG.
-NAPNPW:NON PROG.
-NSERVER: server_tcp.com
-PORT:00260
-PP:00
-F:0
-TM:00005
##D4 G-PIXE - V1.6 - D4
-NGPSA:NON PROG.
-NGPSB:NON PROG.
-NMU TI:NON PROG.
-NSTART:NON PROG.
-NSTOP:NON PROG.
-TS:00000

Spektra S.r.l
Spektra S.r.lSpektra S.r.l
Spektra S.r.l.
..
.- via Pavia 29, 21052 Busto Arsizio (VA) – ITA
ITAITA
ITA Y
Y Y
Y -
--
- www.spektra
www.spektrawww.spektra
www.spektra-
--
-srl.it
srl.itsrl.it
srl.it [e-mail]
[e-mail]@email.it
[e-mail] 10
##D5 G-PIXE - V1.6 - D5
-DATE:XX/XX/XX
-TIME:XX:XX:XX
-AT:XXXX.XXXXX
-ON:XXXXX.XXXXX
-SPEED:XXX
-DIR:XXX
-SAT:XX
-FIX:X
##D6 G-PIXE - V1.6 - D6
-MAIN CE :
-MCC:xxx
-MNC:x
-AC:xxxxx
-CID:xxxxx
-SIGN:xx
-BER:xx
##D7 G-PIXE - V1.6 – D7
- CONN_V:0
- SIGN:xx
- BATTERY:3.6V
- IMEI:012346789012345
- TCP:0->0
- SMS :0->0
##D8 G-PIXE - V1.6 – D8
- NA-IN: NON PROG.
- NA-OUT: NON PROG.
##D9 G-PIXE - V1.6 - D9
1: 2:I:+45.3201:+008.5058
2: 5:O:+33.2718:+008.5827
3: 0:I:+33.2718:+008.5827
4: 0:I:+33.2718:+008.5827
5: 0:I:+33.2718:+008.5827
##DX request all cell-id of all network available.
##PI request the last point stored (view the general note for details)