Spectra nTier500 User manual

SpectraLogic.com
Spectra nTier500 and
nTier500 VTL
Rack-mount Installation Guide

2
Rack-Mounting Instructions 90990047
Copyright Copyright © 2009 Spectra Logic Corporation. All rights reserved. This item and the
information contained herein are the property of Spectra Logic Corporation.
Notices Except as expressly stated herein, Spectra Logic Corporation makes its products and
associated documentation on an “AS IS” BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, BOTH OF WHICH ARE EXPRESSLY DISCLAIMED. In no
event shall Spectra Logic be liable for any loss of profits, loss of business, loss of use or
data, interruption of business, or for indirect, special, incidental or consequential
damages of any kind, even if Spectra Logic has been advised of the possibility of such
damages arising from any defect or error.
Information furnished in this manual is believed to be accurate and reliable. However, no
responsibility is assumed by Spectra Logic for its use. Due to continuing research and
development, Spectra Logic may revise this publication from time to time without notice,
and reserves the right to change any product specification at any time without notice.
Part Number 90990047 Revision B
Revision
History
Contacting
Spectra Logic
Revision Date Description
A February 2009 Initial release
B April 2009
Update to reflect rebranding of nTier300 VTL to
nTier500 VTL
To obtain general information
Spectra Logic Web Site: www.spectralogic.com
United States Headquarters European Office
Spectra Logic Corporation
1700 North 55th Street
Boulder, CO 80301
USA
Phone: [phone] or 1.303.449.400
International: 1.303.449.6400
Fax: [phone]
Spectra Logic Europe Ltd.
Magdalen Centre
Robert Robinson Avenue
Oxford Science Park
OXFORD
OX4 4GA
United Kingdom
Phone: [phone]
Fax: [phone]
SpectraGuard Technical Support
Web Site: www.spectralogic.com/support Knowledge Base: www.spectralogic.com/knowledgebase
United States and Canada
Phone:
Toll free US and Canada: 1.800.227.4637
International: 1.303.449.0160
Email: [email protected]
Europe, Middle East, Africa
Phone: [phone]
Email: [email protected]
Deutsch sprechende Kunden
Phone: [phone]
Email: [email protected]
Mexico, Central and South America, Asia, Australia, and New Zealand
Phone: [phone]
Email: [email protected]

3
Rack-Mounting Instructions
These instructions describe how to install the Spectra nTier500 or
nTier500 VTL (the nTier appliance) in a standard 19-inch, four-post rack.
Do not install the data drives until after the rack-mounting procedure is
completed.
Before You Begin
Perform these tasks, obtain these items, and note the warnings:
Identify the location where you will install the Spectra nTier appliance.
Assemble the rack, if necessary.
Obtain the following tools and equipment:
#2 Phillips screwdriver, magnetic if available
Measuring tape (recommended)
Level (recommended)
Ensure Rack Stability
Warning
The rails provided with the library are designed for a standard 4-post 19-inch
(48 cm) rack.
A 2-post rack will not support the weight of the nTier appliance.
German: Die Schienen, die mit der nTier sind für ein Standard-4-post-19-Zoll
(48 cm) Rack.
A 2-post-Rack wird nicht das Gewicht der nTier .
Warning
If you are not installing any other equipment in the rack, install the Spectra nTier
appliance near the bottom of the rack to prevent the rack from being top-heavy.
German: Wenn Sie nicht die Installation ein anderes Gerät im Rack, installieren Sie
die Spectra nTier in der Nähe der Unterseite des Schranks zu verhindern, dass der
Schrank von der kopflastigen.
Warning
The nTier appliance weighs approximately 54 lb. (25 kg) without drives installed.
Use extreme caution when moving it. Always use two people, one on each side,
when lifting or moving it.
German: Die nTier Gerät wiegt ca 25 kg., ohne Laufwerke installiert. Verwenden Sie
extreme Vorsicht walten lassen, wenn sie abwandern. Benutzen Sie immer zwei
Personen, eine auf jeder Seite, beim Heben oder Fortbewegen.

4
Rack-Mounting Instructions 90990047
Identify the Rack-mount Kit Components:
Warning
To reduce the risk of personal injury or damage to equipment:
Extend leveling jacks to the floor.
Ensure that the full weight of the rack rests on the leveling jacks.
Install stabilizing feet on the rack.
In multiple-rack installations, secure racks together.
Extend only one rack component at a time. Racks may become unstable if more
than one component is extended.
German: Sicherheitshinweise zur Vermeidung von Verletzungen und
Beschädigungen:
Stellen Sie sicher, dass die Standfüße des Racks den Boden vollständig
berühren das Gewicht des Racks vollständig auf den Standfüßen ruht.
Installieren Sie nötigenfalls stabilisierende Komponenten im Rack.
Sofern Sie mehrere Racks nebeneinander installieren, fixieren Sie diese
untereinander.
Ziehen Sie immer nur eine Rack-Komponente aus dem Rack. Das gleichzeitige.
Ziehen mehrerer Komponenten kann dazu führen dass das Rack nach vorne
kippt.
Component # Required Use
2 rail assemblies Mount chassis in rack. Each
assembly includes:
Rail
Slider
Extender plate
Bag labeled 1 RAIL.
6 or more screws
Attach rail sliders to chassis.
Bag labeled 2
4 small nut plates
12 (or more)
screws
Attach rail assemblies to rack.
Rail assemblies
Small screws
Small nut plates
and screws

April 2009 Spectra nTier500 and nTier500 VTL
5
INSTALL THE RAILS
Each rail assembly consists of an inner slider that is attached to the nTier
appliance and an outer rail that is attached to the rack.
Prepare the Rails
Disassemble the rail assemblies.
1. Extend the slider from the outer rail until the safety latch is visible, as
shown in Figure 1.
2. Press up on the latch as shown in Figure 1 to release the latch.
3. Pull the slider completely out of the outer rail.
4. Repeat steps 1–3 for the second rail assembly.
Bag labeled 3
4 large nut plates
12 (or more)
screws
Attach rail assemblies to rack.
Bag labeled 4
4 clip nuts
4 screws
Secure nTier appliance to rack.
Component # Required Use
Large nut plates
and screws
Clip nuts
and screws
Figure 1 The safety latch and mounting holes.
Press up to release safety latchSlider Outer rail

6
Rack-Mounting Instructions 90990047
Install the Sliders on the Chassis
1. Remove the nTier appliance from its bag and place it on a sturdy work
surface where you can reach both sides of the chassis. Having two
people for this task simplifies lifting and moving the chassis.
2. Position a slider against one side of the chassis with the latch toward
the rear of the chassis and pointing toward the front of the chassis.
Make sure the safety latch is toward the outside.
3. Slide the end of the slider (furthest from the latch) under the tab near
the front of the chassis so that the tab fits into the notch on the end of
the slider.
o
Figure 2 Position the latch toward the rear.
o
Figure 3 Insert the slider under the tab.
Latch
Rear of chassis
Tab
Front of chassis

April 2009 Spectra nTier500 and nTier500 VTL
7
4. Position the slider so that the three holes circled in Figure 9 align with
the holes in the side of the chassis.
5. Use a #2 Phillips screwdriver to install a screw from bag 1into each
hole, securing the slider to the chassis. Tighten the screws snugly.
Note: If you cannot align the three holes circled in Figure 9 with the
holes in the chassis, use the other screw holes in the slider to
install the screws. You only need three screws to attach the slider
to the chassis.
6. Repeat Steps 2 through 5 to attach the second slider to the other side of
the chassis.
Adjust the Length of the Outer Rails
1. If necessary, loosen the screws attaching the extender to the outer rail so
that you can adjust the length of the rail. See Figure 10 to see a close-up
of the rail with the extender attached.
2. Position one of the rails against the inside of the rack with the extender
toward the back of the rack.
o
Figure 4 Attach the slider to the chassis.
Screws
Important
The length of the rails must be adjusted before they are attached to the rack.
o
Figure 5 Adjust the position of the extender attached to
rail end.

8
Rack-Mounting Instructions 90990047
3. Adjust the position of the extender so that the assembled rail just fits in
the inside distance from the front mounting holes of your rack to the
back mounting holes.
Note: Using a measuring tape simplifies determining the length
required for the rails to fit inside the rack.
4. Tighten the four screws holding the extender to the rail.
5. Repeat Steps 1 through 4 for the other rail.
Install the Outer Rails in the Rack
1. Examine the mounting holes in your rack and select the set of nut plates
and screws (either bag 2or bag 3in the rack kit) that best match these
holes.
2. Determine where to install the nut plates on the rack. The plates must
be positioned to provide at least 2 inches of clearance below the bottom
edge of the plate.
3. Position a nut plate behind one rack post at the desired position, then
use a #2 Phillips screwdriver to screw three ½-inch screws into the
plate, as shown in Figure 11. Tighten the screws only enough to hold
the plate in place.
4. Repeat Step 3 to install the nut plates on the each of the other three
posts of the rack.
Note: Make sure that the nut plates are installed at the same level on
all four posts. Otherwise the rails will not be level when they are
installed. Using a level simplifies positioning the nut plates so
that the rails will be level.
o
Figure 6 Loosely attach the nut plate
to the rack.
2 inches
Nut Plate
Screws

April 2009 Spectra nTier500 and nTier500 VTL
9
5. Fit the tabs on one rail extender between the nut plate and one of the
back rack legs. Then, fit the front tabs on the rail between the nut plate
and corresponding legs on the front of the rack. Tighten all three screws
to secure the nut plate to the rack.
6. Repeat Step 5 to attach the second outer rail to the rack. Set aside any
leftover screws and parts.
7. On the front of the rack, attach two clip nuts (bag 4in the rack kit), to
each leg. Place one above and another below the rails, with one empty
hole separating each clip nut from the nut plate mounting screws, as
shown in Figure 13.
o
Figure 7 Insert the rail tabs between the nut plate and the rack.
Tabs
Front
(behind post)
Rear
Tabs
o
Figure 8 Attach clip nuts to the front of the rack.
Clip nut
Clip nut
Empty hole
Empty hole
Mounting screws
for nut plate

10
Rack-Mounting Instructions 90990047
INSTALL THE NTIER APPLIANCE INTO THE RACK
1. Lift the nTier appliance and slide it onto the rails in the rack until the
mounting ears on the front of the chassis fit against the rack, with the
mounting ear screw holes directly over the clip nut holes (see Figure 9).
Warning
The nTier appliance weighs approximately 54 lb. (25 kg) without drives installed.
Use extreme caution when moving it. Always use two people, one on each side,
when lifting or moving it.
German: Die nTier Gerät wiegt ca 25 kg., ohne Laufwerke installiert. Verwenden Sie
extreme Vorsicht walten lassen, wenn sie abwandern. Benutzen Sie immer zwei
Personen, eine auf jeder Seite, beim Heben oder Fortbewegen.
Caution
Do not install the data drives until after you secure the chassis to the rack. A fully
loaded nTier appliance is heavy. Most of the weight is toward the front of the
chassis.
Figure 9 Slide the chassis into the rack.

April 2009 Spectra nTier500 and nTier500 VTL
11
2. Use a #2 Phillips screwdriver to install the two clip nut screws in each
mounting ear to secure the chassis to the rack.
3. The rack installation is now complete. Continue with the installation as
described in the documentation that accompanied your nTier
appliance.
Figure 10 Secure the chassis to the rack (left side shown)
Screw
Screw
Mounting ear

12
Rack-Mounting Instructions 90990047
Notes