Spectrum CPU Sling 38925 Quick start guide

Assembly InstructionsAssembly Instructions
0192445 Page 1 of 2
Assembly InstructionsAssembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
CPU SlingCPU Sling
3892538925
For electric Flex Active Tables,For electric Flex Active Tables,
Esports Evolution, Evolution desksEsports Evolution, Evolution desks
(4) 0101382
#14 x 7/8” PHSM
Worksurface
(1) 0160670
CPU sling
• Provides CPU tower storage under worksurface
• 5”-8.5”W x 18”D x 17.935”H
• The 38925 CPU Sling is specically designed for use with
electrically adjustable Flex Active tables, Evolution, and
Esports Evolution desks.
(1) 035674
3/4” bumper
(1) 060048
Base
(2) 0160741
Bracket
(2) 034195
1/4-20 wing nut
1. Attach base to sling1. Attach base to sling
1. Align the base with the CPU sling and secure with
(2) 1/4-20 wing nuts. Figure 1.
Figure 2
(2) 0107595
58” strap / buckle
assembly
CPU Sling
Bracket
Bracket
#14 x 7/8” PHSM
(1 per bracket)
(2) #14 x 7/8”
PHSM
2. Attach sling to worksurface2. Attach sling to worksurface
Figure 1
Sling base
(2) 1/4-20
wing nut
CPU Sling
1. Determine which side of the worksurface you’d like the CPU sling.
(Left or right).
2. Align the CPU sling with the worksurface pilot holes and secure with
(2) #14 x 7/8” PHSM screws. Figure 2.
3. Secure each bracket to the worksurface as shown with (1) #14 x 7/8”
PHSM screw.

0192445 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2021 Spectrum Industries Inc., All rights reserved.
Care should be taken when moving the
desk / table on casters to prevent tipping or
shifting of the CPU tower(s) during transit.
Sling bracket
3. Install straps3. Install straps
1. Thread each strap through the slots in the sling bracket and
base as shown in Figure 3 with the tails hanging down.
2. Thread each strap through the buckles as shown.
3. Place the 3/4” bumper between the leg and CPU sling.
Figure 3
Strap / buckle
assembly
Buckle
Bumper
Sling base
CPU tower
1. Slide the base to the widest position and carefully place the CPU
tower into the sling. Figure 4.
2. Slide the base tight against the tower and tighten the two wing nuts.
3. Position both buckles at the same height.
4. Tighten the straps by pulling the tails down until the CPU tower and
base are level and secure.
4. Install CPU tower4. Install CPU tower
Figure 4
Tails
1/4-20 Wing nut
(2 required)
Sling base
2
1
3
1
2
CPU Sling
4
Nylon straps
Nylon straps