Speedrid A1 User manual

Speedrid electric scooter A1
Speedrid

Content
1.Safety Instruction ......... ................ . 01
2.Product List .........
........... ... .. ... .. . 05
3.Function Diagram .........
............... . 06
4.Display Switch and APP .........
........... . 07
5.Assembly ........
...................... . 10
6.Driving Method .........
................. . 11
7.Charging Method .........
................ . 12
8.Avoid Security Risks .........
.............. . 12
9.Daily Maintenance and Maintenance Suggestions ... 15
10.Basic Parameters .........
............... . 17
11.Warranty .........
..................... . 18
12.Legal Declaration .........
............... . 19
Speedrid electric scooter A1
Thank you for choosing to use Speedrid electric scooter A1 (Hereinafter referred
to as scooter) This scooter is a product that is easy to fold and carry, which is also a
fashionable sports entertainment tool.
Please enjoy the new commuting experience with this scooter!

1. Safety Instruction
Scooter may not allowed to ride on public transport roads. Please observe local laws,
regulations and policies before riding.
The scooter is an entertainment product. You need to practice your riding skills.
Speedrid will not be liable for any damage caused by inexperienced riders or failure to
use the product in accordance with this manual.
Please read this instruction manual carefully and do not attempt to ride the scooter
if you cannot follow the instructions in this instruction manual. Please make sure you
have read the instruction before lending your scooter to others. It is your responsibility
to ensure the safety of novice riders. Please assist him/her in learning how to use this
product until he/she has learned the basic operation of this scooter. Please ensure that
each the rider wears a helmet and other protective gear while riding.
Follow the tips and warnings in this manual could reduce risks, but not eliminate
them all. Remember that you may be at risk of injury or death due to loss of control,
collisions and falls while riding a scooter. Scooter is only suitable for flat hard road, and
it is recommended to be used in relatively closed road environment (such as inside the
community, parks, dedicated sites, etc.). Do not run over obstacles and protrusions. Be
alert and slow down when entering an unfamiliar environment.
To reduce the risk of injury, please be sure to read and follow all "caution" and
"warning" instructions in this manual. Do not exceed the speed limit. Do not ride on
public transport roads under any circumstances.
The product may contain detachable parts, please keep it away from children to avoid
harm caused by swallowing.
motorcycles, cars or other vehicles when you ride on your scooter. Therefore, when you
approach or pass through intersections, curves, doorways, etc.,you need to slow down
and avoid pedestrians, bicycles and vehicles. Be defensive when riding. Pay attention
to traffic and pedestrians.
Please do not speed up or slow down suddenly. When riding, always hold the handle
bar with both hands and stand on the foot pad with both feet. Please do not travel
faster than the limit of the scooter, otherwise there may be a risk of loss of control,
collision and fall down.
Please do not continue to use the scooter if it is damaged, smelly, smoky, overheated,
or the parts are faulty or abnormal, and contact the after-sales service in time.
Do not throw or drop the scooter. Do not place the scooter under fire or high
temperature.
Pay attention to the road conditions, avoid obstacles and do not ride on bumpy road
(including wet ground, loose sand, gravel ground and ice) when riding.
Any modification of the scooter is prohibited.
Protective glasses are recommended when riding. Stunts are not allowed during riding.
In order to avoid distraction when riding the scooter, please do not wear headphones,
earplugs, take phone calls, take photos, video or do any activities unrelated to riding,
so that you can monitor the environment well when riding.
Do not attempt to carry passengers or heavy items, the scooter can only support the
weight of one person. Children or pregnant women riding is prohibited.
When riding this product, please abide by local laws and regulations. It is prohibited
entering in the restricted areas by the laws of the country/region where it is located
and the relevant management units. For your first ride, please do not choose areas
where crowd around children, pedestrians, pets, vehicles, bicycles or other obstacles
and potential hazards.
Please respect pedestrians' right of way when riding. Pass the pedestrians on the
left as possible. When forwarding to a pedestrian, slow down and pull over. Avoid
startling pedestrians, especially the elders, children, the disabled and pregnant
women. When approaching pedestrians from behind, notice them with the bell and
slow down before passing by.
Be alert at all times when riding. Ride at an appropriate speed, keep a safe distance
from other vehicles at all times, and slow down when entering an unfamiliar
environment. Please keep in mind that there is a risk of collision with pedestrians,
For whatever reason, do not ride your scooter in snow, rain, wet, muddy, icy conditions.
When riding in rain or snow, water could get inside the scooter, leading to the risk of
functional damage, fire and even explosion due to the damp battery. Damage and loss
due to water inflow are not covered by the warranty.
Do not ride in the following conditions: bad weather, poor visibility, dawn, dusk, thick
fog, heavy smoke, night, darkness or extreme fatigue. Each of these situations could
increase the risk of accidents.
Do not ride over obstacles (sand, stones or roadblocks). Doing so may result in a loss
of balance or road holding, leading to a fall. When you encounter steep slopes, rough
sections or other terrain you have not encountered before, please take care of your
own safety and do not take risks riding through.
It is forbidden to ride scooters on highways, motor vehicle lanes, areas near motor
vehicles, steps and their vicinity, swimming pools, slippery and other areas with water,
bumpy ground, soft ground and other areas that may affect normal riding or threaten
cycling safety.
Riding Instruction
Riding environment Requirements
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
9.
10.
11.
 

Use only the parts and accessories designated or approved by us. Do not modify your
scooter, it may affect the operation of the scooter, resulting in serious damage and
warranty lapses.
Scooters are not medical devices and should not be used as medical assistance and do
not use scooters as a shifting tool.
In order to get a better riding experience, it is recommended to have a regular
maintenance .
When riding, the scooter vibration will cause the rider's body vibration.
This scooter is not for children riding. All the cleaning or maintenance activities should
not let children get involved.
This product is suitable for users aged from 14 to 50 years old. Minors riders should
under adult supervision during riding. Riders should wear helmets, knee pads, elbow
pads and other safety protective equipment. Please use a quality scooter or scooter
helmet and tie the strap in a suitable position under the chin. Persons who are not
suitable to ride this scooter include:
·Persons under the influence of alcohol or drugs;
·Persons who are unable to engage in strenuous physical activity due to illness;
·Persons who cannot keep their balance;
·Persons whose weight exceeds prescribed limits (see "Basic Parameters");
·Children under the age of 14;
·Pregnant women.
High heels, slippers and open-toed shoes are prohibited. Keep your hair tied up to
avoid accidents caused by obstructing your vision.
Please read this product instruction carefully before riding.
Before riding the scooter, please check the scooter carefully to ensure that any part
including wheels, brakes, screws, etc., are not loose or damaged, and ensure that the
scooter is in a proper standby state for driving. If the scooter makes abnormal sound or
alarm sound, please stop using it immediately, and consult online customer service for
professional guidance or maintenance services.
In the state of low battery power, the scooter does not have enough power to maintain
your normal riding, please make sure that the battery power is sufficient before riding
to avoid danger.
Do not touch the wheel brake of the scooter as it may cause injury.
Parking on flat solid ground is recommended. If parked on a slope, the kickstand must
be facing downhill to prevent tipping. Do not let the front of the scooter fall down to
prevent the vehicle from tipping over. After pulling down the kickstand, make sure the
scooter could stand still and will not fall down on the ground (due to sliding, wind or
rocking). It is recommended to park against the wall.
Parking without the power off may cause mal-operation movement of the scooter,
causing injury or damage to yourself and the people or property around you, please
be sure to power off the scooter before parking.
OthersRider Requirements
Inspection before Riding
Inspection after Riding
1.
1.
2.
3.
4.
5.
1.
2.
3.
2.
3.
 

Instruction Manual
3mm inner
hexagon wrench*1 Screws*4 Charger*1
2. Product List 3. Function Diagram
Scooter
Speedrid
 

Display: Red blinking red indicates a fault occurs, and the speedometer displays the
fault code. Please contact after-sales service.
Temperature warning: Blinking means the battery temperature reaches 55ȭor lower
than 0ȭ.
Battery display: each sector represents about 20% of the battery.
Bluetooth
Cruise
Car lock
Gear
Long press: Power on/off
Short press: front/rear lights on/off
Double click: Mode switch
* In this status, the scooter's acceleration power is reduced and it may not be able to
recharge. Please leave the scooter to room temperature before charging.
* The last sector display in red, indicating that the battery power is very low , please
charge in time.
Speed display
Headlight on/off display
Mileage display
Power display
4. Display & Switch & APP
Power: long press for power on/off
Under power on status, 1 click for front and rear light on/off
Double click: gears mode swiching
Trible click: Km/hr and Miles/hr speed unit switching.
Quardra click: single mileage/total mileage conversion.
Speedometer: shows the current speed of the scooter. When the malfunction occurs, the
speedometer displays the failure code.
Speed mode: Three modes are available. The maximum speed of each mode is shown in
the table below.
Mode Gears Speed
1 low speed gear 15KM/H
Medium gear 25KM/H
high speed gear 32KM/H
2
3
APP
1. Caution Before using the APP :
(1) TUYA App-There are safety risks when learning to ride the e-scooter. You must
read the Riding Safety via the App before your first ride.
(2) Because TUYA APP has some functions that need to get your phone's permission,
so please choose according to your needs.
(3) Since TUYA APP is an integrated APP for smart home devices.You can not only use
it to control the electric scooter, you can also use it to control other smart appliances
at home that cooperate with TUYA APP.
2. Download : You can download TUYA APP from APP Store or google search.
3.
Note:
Connect : To connect the scooter to TUYA APP, you need to turn the scooter on and
then turn on the Bluetooth of your phone. Finally, open TUYA APP and click the
scooter icon. You can then enter the control interface of the scooter, which includes
the following functions: constant speed cruise, light switch, gear setting, single
mileage, total mileage, scooter lock, scooter power display, Bluetooth connection
status, etc.
If the scooter device has not been searched, you need to reset the connection of the
scooter. Operation method of reset: Hold the brake tightly, pinch the bottom to do
so, and then press the power on button 5 times in a row to complete the reset, and
then try to reconnect as above.
The lock function can only be used on the phone. On the electric scooter body can
not be operated to lock, or unlock. Because the main purpose of the lock function is
to prevent theft.
1.
2.
 
mph
km/h
Trip
ODO
Mile
Km

How to use App 5. Assembly
1) Pull the handle bar pole up
right.
2) Press the folding hinge lever to lock
the handle bar pole hinge.
ԮConnect the communication cable connectors in the handlebar and pole.
ԯInsert the handlebar post into the pole and located all the screws.
԰Tighten all the screws to fix the handle bar with the pole.
1.Fold/unfold
2. Assemble the handlebar and pole
 
All Devices
Electric Scooter
Home SceneS mart Me
Electric Scooter
Connected
54%
MAP
Single MileageT otal Mil eage
Mile Mile
0
.
067
. 3
Funcs
Cruise Headlight Level 3
More

6. How to ride
Fold the handlebar post
and snap the hook into the
buckle on the rear fender.
1. Slide: Stand on the stand pad with
one foot and kick back with the other.
3. Deceleration: release accelerator lever
and/or grip the brake level.
4. Turn: Tilt your barycenter slightly and slowly turn
the handle bar.
2. Acceleration: Stand on the foot pad and balance, and
press the accelerator lever with your right thumb.
*Motor start requirements: speed ≥3km/h.
Wear a helmet at all
times while riding.
Riding on public vehicle roads, motorways
and highways are prohibited.
Do not use mobile phones or
wear headphones while riding.
3. Folding
1. Make sure the power is off.
2. Press the safety buckle with your thumb and pull the quick release lever
backward.
3. Fold the pole down to the rear fender.
4. Snap the hook into the buckle on the rear fender.
Check the battery power before riding . If the battery is low, charge it immediately.
Warning: Serious injury may result from falling due to lack of tyre grip when panic
stop . Please keep a safe braking distance and observe road conditions .
Slow down and brake to avoid potential risks .
*
7. How to Charge
8. Safty Risks
Please do not charge when the charging port, charger or power outlet are damp.
When charging, only use the original charger provided by us. Do not use the charger
of any other model.
If the battery is damaged or flooded, do not charge or continue to use the battery.
Before charging or after charging, fasten the rubber plug of charging port.
Please do not charge outside.
1) Remove the rubber
cover on the scooter
charging port.
2) Plug the charger plug
into the port and then
connect charger with the
power supply.
3) After charging,
put the rubber cover
back in place.
Warning
Serious injury may occur if you do not follow the following safety tips. All property
losses and personal injuries caused by this will be borne by the user.
 

Please avoid riding in the rain. At
this time, please detour at a low
speed.
Do not park your scooter
outdoors for a long time.
The scooter is limited to one
person. No passenger (children,
heavy items) carrying is allowed;
It is forbidden to ride with one
or both hands off the handlebar.
Riding with one foot is prohibited.
When encountering speed bumps,
potholes and other unconventional
roads, do not pass at high speed. Keep
low or medium speed (5- 10km/h).
Bend your knees slightly to acclimatize
yourself to the complex road surface.
Pregnant women riding are banned.
Do not press the throttle when you
are pushing the scooter.
Please do not wear high heels
while riding.
Avoid bumping into high obstacles
or gaps such as door frames and
the gaps between the elevators
door and ground floor.
Do not hang heavy objects on the
handlebars.
It is forbidden to steering handlebars
direction rapidly when driving at high
speed .
Do not touch the hub motor after riding,
the motor surface at a high temperature.
Riding the scooter down from
stairs or jumping over an obstacle
is prohibited.
Do not overtake.
Do not step on the rear
fender.
Do not touch the drum brake
while rotating.
 

Please use original battery pack . Do not use other models or brands battery.
Otherwise, safety risks may arise.
When storing or charging the battery, do not exceed the specified temperature
limit.
Do not touch the battery contacts, and do not open or pierce the shell. Avoid
metal objects touching battery contacts, which may cause battery damage or
personal injury.
Do not throw the battery pack into the fire, otherwise the battery may damage,
overheat, or even have the risk of fire.
If the battery is damaged or soaking, do not charge or continue to use the battery.
Do not remove the battery. Removing the battery process is complicated and can
affect the operation of the scooter.
Please do not attempt to remove the battery, otherwise there is a fire risk. Users
are not allowed to repair the parts contained in the product by themselves.
Do not ride the scooter when the ambient temperature exceeds the operating
temperature of the product, because low/ high temperatures will result in limited
maximum power. This may lead to skidding or fall during riding, resulting in
personal injury or property damage.
After each riding, please fully charge the battery before storing, which is conducive
to prolong the battery life time. Complete battery drain may cause permanent
battery damage. Avoid draining all the power of the battery.
Improper disposal of waste batteries may seriously pollute the environment. When
discarding the battery pack, comply with local regulations. To protect the natural
environment, do not discard the battery.
Note: A fully charged scooter standby time about 120-180 days. The battery has a
smart chip that stores information about its charge and discharge record. If you do
not charge the battery for a long time, it may cause serious damage, so the battery
can no longer be charged. This damage is not covered by the free warranty.
Note: Disassembly by unauthorized personnel is strictly prohibited as there is a risk of
electric shock or serious injury due to short circuit.
1)
3)
4)
5)
2)
6)
7)
8)
9)
10 )
2 Battery Maintenance
 
If you have any stains on the outer shell of your electric scooter, wipe the stains
with a soft damp cloth; You can clean it with toothpaste and a toothbrush, and
then remove them with a damp cloth. If scratches are found on plastic parts,
polish them with sandpaper or other abrasives.
Warning: Do not clean the scooter with alcohol, gasoline, kerosene or other
corrosive solutions or volatile chemical solvents. Otherwise, it will cause serious
damage to the surface of the scooter and may destroy the structure of the
internal elements. Do not clean the scooter under strong water pressure and
ensure that the power is turned off. In addition, the rubber cover needs to be
plugged into the charging port after charging the battery, otherwise power loss
may occur, or water falling into the port may cause serious damage.
If you do not use the scooter, store it in a dry and cool place and do not leave it
out on the street for long periods of time. Leaving the device under the sunlight/
at extremely high/low temperatures will cause rapid aging of the plastic shell
and tyres or reduce battery life time.
9. Daily Maintenance and Maintenance
Suggestions
Tip: Please perform the following operations after power off
1)
2)
3)
1Cleaning and storage

Failure caused by not following the instruction manual.
Normal wear and tear, accident, abuse, neglect of care, improper assembly, or
incorrect parts maintenance and incorrect use of accessories by any user.
It is a part that will naturally wear out under normal use, and it is not applicable
to those who are free of charge during the aforementioned warranty period.
Failure to perform proper replacement and maintenance due to wear and tear of
consumables, causing other parts to malfunction and damage.
The valid invoice or warranty card does not match or alter the model of the car.
Damage caused by overloading, riding over obstacles (including but not limited
to descending steps,falling, etc.), performing extreme sports, etc.
Damage caused by force majeure (such as: fire, earthquake, lightning, water
damage, etc.).
Those who exceed the warranty date.
Appearance accessories and consumables are not after-sale if they are damaged.
The consumables including inner tubes, outer tires, and scooter pieces are not
guaranteed. Precautions the following situations are not quality issues and do not
apply to this warranty.
All other parts except consumable parts are guaranteed for 12 months for problems
caused by manufacturing process or material defects. For instance: brake blocks,
brake pads, brake handles, tires, and brake tubes are consumable parts.
We offer warranty to the original purchaser of the Product and this warranty does
not apply to any third parties.
Warranty Period
10. Warranty 11. Basic Parameters
One-Year Limited Hardware Warranty
Your E-scooter includes a One -Year Limited Hardware Warranty. The Warranty covers
product defects in materials and labor cost under normal use .
We offer warranty of frame with 12months. As per any problem regarding to
manufacturing process and material defects,which includes product breakages
during the riding (except riding improperly).
We offer 12 months Battery and Motor Warranty, But this warranty does not cover
faulty operation or failure to property follow the manufacture's instructions.
Note:
Attentions:
1.
2.
3.
4.
5.
6.
7.
8.
Performance
Index Item Parameters
Product Model
Product Name
Product Size 1160*520*1200mm
Folding Size 1160*180*500mm
Net Weigh 15.91kg
Max. Load 100kg
Applicable Age 14-50 Years Old
Applicable Height 150-200cm
Mileage
Max. Speed 32km/h
Max. Slope
Applicable Terrain
10%
45km (85 kg loading, riding at constant speed 20km/hr on
smooth roads)
Asphalt/flat surfaces, stairs not higher than 1cm, gullies not
more than 3cm wide
Overcharge/overheat/overdischarge /short circuit/overcurrent
protectio
Working Temperature -10°C-40°C
Storage Temperature -20°C-50°C
Waterproof Level
BMS Intelligent BMS
Nominal Output
IP54
Charging Time
Nominal Power
Output Power
Around 6-7 hours
500W
Nominal Voltage
Input Voltage
Tyre Pressure
Max. Input Voltage
Front and Rear Tyre
36V
AC180-240Vǡ50/60Hz
42V
42V 2A
83W
45Pls
Pneumatic Tyre
Max. Charging
Voltage 42V
Nominal Power
Capacity 468Wh
Nominal Capacity 13Ah
Charging Temperature -0°C-40°C
Electric Scooter
A1
Basic
Information
Riding
Requirements
Scooter
Battery
Motor
Charger
Tyre
 

Before driving the scooter, please check the scooter carefully to ensure that there is
no loose or damaged part before driving.
Whether before driving, during driving or parking, please pay attention to the
intersection to avoid unnecessary damage to yourself or the surrounding objects.
In the process of driving, if the tire appears loose signs, please stop immediately for
inspection, in order to avoid danger.
Driving A1 electric scooter must get on from both sides of the scooter and wear
professional protective gear.
Do not wear high heels while driving A1 scooter.
Do not immerse the battery and scooter in water, expose to heavy rain or drive in
the rain for a long time. Do not clean it with strong water flow and high-pressure
hose to avoid water inlet. Do not wipe the body of any operation, so as not to cause
improper warranty.
On rainy days, the braking performance of electric scooters (including other
vehicles) will be greatly reduced, and the resistance of tires will also be relatively
reduced. It makes it more difficult for cyclists to control the speed and more likely
to lose control. To ensure safe driving in rainy weather, please drive slowly and
brake in time.
Do not take risks. When you encounter steep slopes, rough sections or other terrain
that you have not encountered before, please pay attention to your safety and do
not take risks riding through.
Drive with caution. Be aware of yourself, vehicles and pedestrians.
Please pay attention to the following conditions when driving: vehicles in front of
you, vehicles behind you to overtake, open doors, pedestrians and other obstacles
that distract your attention while driving. These may lead to accidents.
If the laws and regulations of your region or country allow you to drive an electric
scooter on the road, please follow the driving direction stipulated by the local
government law.
Please do not be dragged with your arm attached to another vehicle.
Please do no stunts while driving.
Do not drive in bad weather, poor visibility, dawn, dusk or extreme fatigue, as each
of these conditions increases the risk of an accident.
Do not drive alone in remote areas. Even when driving with other people, make
sure someone knows your destination and expected return time.
When riding, you are taller than usual. Please pay attention to the extra height
added by the electric scooter and helmet, and be vigilant when riding indoors,
outside or in other positions close to your head.
Do not wear loose clothing when riding. In order to avoid clothing and wheel
friction, affect the normal operation of the scooter.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
 
Product Legal Notice
12. Legal Declaration
Thank you for choosing A1electric scooter. A1 electric scooter is a fashionable
sports equipment,but when it enters a public area, it will have the property of a
vehicle. Therefore, it also has the risk that all vehicles may have, namely, when you
drive A1electric scooter, there will be a loss of control risk of collision and fall, you
have the responsibility and obligation to learn how to drive A1electric scooter, and
strictly comply with the relevant local laws and regulations we hope you to ensure
safety, and enjoy learning to drive safely. Thinking about how do you learn to drive
in other means of transport. There may have been someone to help you learn and
keep you in a safe driving environment. All of these lessons apply to the learning
of the A1 electric scooter. Please carefully read and study A1 Electric Scooter
Instruction Manual and A1 Electric Scooter Legal Statement before use, and obtain
relevant learning information from our website, aiming to help you learn safe driving
techniques. Compared with other equipment, driving the A1 little White electric
scooter exposes the risk of injury. You can reduce the risk by using the warnings and
precautions in A1 Electric Scooter Instruction Manual, but it cannot eliminate the
risk. Please read carefully the prohibitions and warnings set out in A1 Electric Scooter
Instruction Manual and the following legal notices .
The more familiar you are with electric scooters, the easier it will be to drive, so we
invite you to:
Read A1Electric Scooter Instruction Manual carefully before driving practice;
Please do not allow people to use your electric scooter without carefully reading
A1 Electric Scooter Operation Manual;
All parts of electric scooter must be installed in accordance with A1 Electric
Scooter Operation Manual. Improper installation may bring risks of loss of
control, collision or fall. Before installation and maintenance, please turn off the
power, and install the parts with proper strength. Too loose or too tight will lead
to damage or failure of the scooter.
Do not charge when the socket is wet. When charging,please plug the power cord
into the correct socket (170V-260V - 50/60Hz), and keep away from children and
pets. Keep away from flammable objects.
Do not place the battery in an environment with high temperature exceeding
45°C or low temperature below - 20° C.
If the battery is damaged, smelly, smoky or overheated, do not continue to use
the battery, and avoid contact with other objects.
There are harmful substances in the battery. Please do not try to open or remove
the battery.
You need to be familiar with the operation method of A1 electric scooter to
operate it outdoors. The more you practice, the safer you will be when driving in a
new environment. The first practice is best under the guidance of an experienced
person or instructor.
1.
2.
3.
4.
5.
6.
7.
8.

It is recommended that you wear protective glasses while driving to keep dirt, dust
and insects out of the air. Use lenses of different lightness, dark lenses for high light
and high transparency lenses for low light.
It is forbidden to carry passengers, and pregnant women are not suitable to drive
A1 electric scooter. A1 electric scooter is for a person only. It is forbidden for two
people to ride the same scooter at the same time and to ride with children in arms.
A1 electric scooter is not a medical device, please do not use it as a medical
assistance tool. You can drive only when you are able to get on and off A1 electric
scooter without assistance.
Do not drive on stairs, elevators or through revolving doors.
Do not drive in poor visibility. Make sure you can see clearly while driving.
It is prohibited to use A1 electric scooter as a shifting tool.
When approaching or passing corners, doorways, etc., slow down and avoid
pedestrians, bicycles and motor vehicles.
A1 Electric scooters, like any other means of transportation, require you to remain
alert at all times while driving. Do not attempt to drive A1 scooter if you are ill or
cannot fully follow the instructions in A1 Scooter Instruction Manual. Do not drive
A1 scooter under the influence of drugs or alcohol.
In order to avoid distraction when driving A1 electric scooter, please do not take
phone calls or do any activities that may distract your attention while driving, so
that you can monitor the external environment well when riding.
The age requirement for riding the A1 scooter is: 14-50 years old. Special note to
parents: As a parent or guardian, you are responsible for the activities and safety of
your minor children. It is recommended that you do not allow your children to drive
the A1 scooter.
Avoid sudden braking, especially on smooth roads, easy to lose traction tire,
increase the possibility of your fall.
Parking without the kickstand is easy to cause the scooter tilt, please be sure to take
the kickstand down after parking.
Refitting may endanger your safe driving. It is forbidden to refit A1 electric scooter
without permission.
If you drive A1 scooter in summer, please note the following: A1 scooter should be
stored in a relatively safe environment, the temperature should not be higher than
45°C and should not be exposed to outdoor sunlight for a long time.
If you are riding A1 scooter in winter, you should pay special attention to the
following: Keep A1 scooter in a safe environment at a temperature not lower than
-2°C (if the storage environment is lower than 0°C, please place the scooter in a
greenhouse for half an hour before charging)
You are obligated to be aware of the laws in your territory and to comply with the
applicable laws.
We cannot assess whether the safety of each non-A1 electric scooter original part
will be endangered when it is used in the product. Even if approved by our official
department, we cannot make necessary guarantees for such products. If there is
any problem with the product, please feel free to contact the after-sale department
of our company, which is your most guaranteed choice.
41.
42.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
The company shall not be liable for all claims, liabilities
and losses caused or likely to result from consumers'
violation of the above stated terms, and riders shall
be solely liable for unforeseen or unavoidable risks
encountered during driving. You may choose to accept
the above terms to use the product; You can also choose
not to accept the above terms and return the goods.
When returning the goods, please keep the products and
packaging intact, which will not affect the second sale.
 

Contacts
Contact usif you experience issues relating to riding,
maintenance and safety, orerrors/faults with your E-Scooter.
Speedrid Customer Service: [e-mail]
Tel: [phone] Monday-Friday 9:30AM-6:00PM
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Made in China