Sportcraft KT Sports TURBO HOCKEY User manual

313 Waterloo Valley Road / Mt. Olive, NJ 07828 / www.sportcraft.com / [phone] / Fax: [phone]
2-1-57-013 HG
TURBO HOCKEY
For Replacement Parts (24hrs / 7days)
order direct at www.sportcraft.com,
or call our
Express Parts Center [phone]
For Technical Support (9:00am to 5:00pm EST) call
Sportcraft Consumer Service at [phone]
ASSEMBLY, INSTRUCTIONS AND RULES

©2005 KT Sports
9
English
English
English - 1
1. Read all instructions - All the safety and operating instructions should be read
carefully before this turbo hockey game is played.
2. Caution - This is not a toy and is intended for use by or under the supervision of adults. Adults should
review safety guidelines with children to avoid possible risk of electric shock or other injuries.
3. Power sources - This hockey game should be operated only from 100-125V A.C., 50/60 cycle current as
indicated on the identification label. If you are not sure of the type of power supply to your home, consult
your appliance dealer or local power company.
4. Power cord protection - Power cord should be routed so that it is not likely to be walked on or pinched
by items placed upon or against it. Pay particular attention to cords at plugs, convenience receptacles,
and the point of exit from the game.
5. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric
shock.
6. Object and liquid entry - Never push objects of any kind into this game through openings as they may
touch dangerous voltage points or short-out parts which could result in a fire or electric shock. Never
spill liquid of any kind on the game.
7. Ventilation - Openings in the game are provided for the exhaust air to create a cushion effect. The
openings on the air blower are for the intake air. Keep clear of the air blower when it is on. Do not put
hand or other objects near the intake openings. To ensure reliable operation of the game and protect it
from overheating these openings must not be blocked or covered.
8. Damage requiring service - Unplug the game from the wall outlet. Do not attempt to service the blower
yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer
servicing to qualified service personnel under the following conditions.
A. When the power supply cord or plug is damaged.
B. If liquid has spilled, or objects have fallen into the blower.
C. When the air blower exhibits a distinct change in performance e.g. abnormal noise, this indicates a
need for service.
9. Grounding or Polarization - This game is equipped with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
10. CAUTION - ELECTRICALLY OPERATED PRODUCT - Not recommended for children under 8 years of
age. As with all electrical products, precautions should be observed during handling and use to reduce
the risk of electric shock.
11. We recommend that the game be periodically examined for conditions that may result in the risk of fire,
electrical shock, or injury to persons. In the event such conditions exist, the game should not be used
until properly repaired.
SAVE THESE INSTRUCTIONS
WARNING: To Reduce The Risk Of Fire Or Electric Shock,
Do Not Use This Fan With Any Solid-State Speed Control Device
IMPORTANT SAFETY INSTRUCTIONS

©2005 KT Sports
6
11
0905 - C
9-3-34-012HG01 (4) 9-3-34-012HG02 (4) 9-3-34-074HG09 (4) 9-3-34-058HG02 (4)9-3-34-058HG01 (4)
9-3-34-089HG05 (24) 9-3-27-093SC28 (24) 9-3-27-093SC11 (16)9-3-36-020HG09 (16) 9-3-34-001HG05 (6)
9-3-34-001HG10 (2) 9-3-34-015SC10 (2)9-3-34-056HG51 (2) 9-3-34-406HG07 (2)
2 3 4 5 1
7 8 9 10
12 13 14 15
by
TM
9-3-34-040AHG06 (2)
10
English
English
English - 2
8 X 38MM ALLEN
KEY BOLT
PARTS IDENTIFIER
LEG COVER LEG SUPPORT BASE
22MM FLAT WASHER 22 GRAM POWER PUCK
ROUND ( RED)
DELUXE POWER
PUSHER (RED)
PUCK RETURN TRAY
WITH SCREW
(PRE-INSTALLED)
TOOLS REQUIRED FOR ASSEMBLY:
· Phillips and Slotted Head Screwdrivers (or Power Driver) - not included
· Allen Key - included
· 12V DC Adaptor - included
(PRE-INSTALLED)
FORWARD GOAL
TRIGGER
LEG LEG SUPPORT - BLEG SUPPORT - A
6 X 45MM ALLEN
KEY BOLT
18MM FLAT WASHER
DELUXE POWER
PUSHER (BLACK)
PUCK RETURN BOX
WITH TRIGGER
MODEL # 2-1-57-013 HG
Congratulations on owning a new KT Sports Turbo
Hockey game! We at KT Sports hope you will have many
hours of enjoyable use with this product.
WARNING: Choking Hazard -- This table contains small balls and/
or small parts. Not for children under 3 years.
!
IMPORTANT!
Please Keep Your Instructions in the storage pouch provided underneath your
table! Your Model number (also located on the underside of the table) is necessary should
you need to contact us. Before attempting assembly, please read through this instruction
book to familiarize yourself with all the parts and assembly steps. We recommend that
two adults assemble this game. Please refer to the Parts Identifier below and be sure
that all parts have been included.
For Replacement Parts (24hrs / 7days)
order direct at www.sportcraft.com
or call our
Express Parts Center [phone]
For Technical Support (9:00am to 5:00pm EST) call
Sportcraft Consumer Service at [phone]

©2005 KT Sports
21
26
9-3-34-086HG08 (4)
9-3-57-013HG01 (2) 9-3-27-080SC21 (4)
9-3-34-074HG04 (2)
9-3-34-089HG13 (60)
9-3-34-091HG07 (1)
9-3-34-089HG16 (4)
9-3-34-089HG14 (4)
9-3-34-040AHG11 (2)
9-3-34-058HG04 (1)
17 18 19 20 16
22 23 24 25
27 28 29 30
36
41
9-3-34-004SC03 (1) 9-3-34-406HG19 (1)
9-3-34-082HG17 (32)
+16
9-3-34-082HG16 (16)
9-3-34-406HG12 (1)
9-3-34-058HG06 (2)
9-3-34-406HG10 (2)9-3-34-086HG19 (2) 9-3-34-406HG09 (1)
9-3-34-058HG05 (2)
32 33 34 35 31
37 38 39 40
42 43 44 45
9-3-34-012HG14 (2)
9-3-34-012HG15
(2) 9-3-34-012HG16 (2) 9-3-34-012HG18 (2)9-3-34-012HG17 (2)
47 48 49 50
46
H
O
M
E
VISITO
R
H
O
M
E
VISITO
R
9-3-34-406HG11 (1)
9-3-34-406HG13 (1) 9-3-34-406HG14 (1) 9-3-34-406HG15 (2) 9-3-34-406HG16 (1) 9-3-34-406HG17 (2)
9-3-34-406HG18 (1)
9-3-34-012HG21 (8)
9-3-34-058HG03 (2)
11
51
9-3-57-013HG02 (4)
9-3-57-003HG08 (2)
English
English
English - 3
PUCK RETURN COVER
6" METAL BELL
LEG LEVELER
STORAGE DOOR
(BLACK)
5MM ALLEN KEY
4 X 65MM WOOD
SCREW
3 X 16MM FLAT
HEAD SCREW
(PRE-INSTALLED)
(PRE-INSTALLED)
(PRE-INSTALLED)
(PRE-INSTALLED)
END GOAL COVER
(BLACK)
DIE CAST SLIDE
SCORER ASSEMBLY
3.5 X 25MM WOOD
SCREW
12V DC ADAPTOR
(PRE-INSTALLED) (PRE-INSTALLED)
6 X 12MM ALLEN
KEY BOLT
METAL PLATE
(PRE-INSTALLED) (PRE-INSTALLED)
LOWER END APRON LOWER SIDE APRON
(PRE-INSTALLED) (PRE-INSTALLED)
(PRE-INSTALLED)
(PRE-INSTALLED)
ON/OFF SWITCH
BLOWER AND WIRE
CONNECTOR
APRON CORNER WITH
WINDOW (BLACK)
APRON CORNER
(BLACK)
3.5 X 14MM WASHER
HEAD SCREW
TOP STORAGE DRAWER
(BLACK)
BOTTOM STORAGE
DRAWER (BLACK)
SCORER - HOME WITH
43" WIRE & SCREW
CONTROL WIRE CONNECTING BOX PUCK CATCHER
WIRE
(PRE-INSTALLED)
(PRE-INSTALLED)
SCORER - HOME WITH
18" WIRE & SCREW
SCORER - VISITOR WITH
18" WIRE & SCREW
CONTRL BOX
WITH SCREW
SCORER - VISITOR WITH
43" WIRE & SCREW
(PRE-INSTALLED)
(PRE-INSTALLED)
SCORER - CLOCK WITH
WIRE & SCREW
CONNECTING WIRE
(PRE-INSTALLED)
SCORER BASE BOX
WITH SCREW
NAME PLATE
1.2 X 10MM NAIL
(PRE-INSTALLED)
(PRE-INSTALLED) (PRE-INSTALLED)
(PRE-INSTALLED) (PRE-INSTALLED)
4 X 40MM FLAT HEAD
SCREW
(PRE-INSTALLED)
(PRE-INSTALLED)
TOP CORNER CAP
(BLACK)

©2005 KT Sports
FIG. 2 FIG. 2A
FIG. 1
FIG. 1A
FIG. 2B
28
28
27
37
46
44
27
38
45
42
30 29
16
43 39
49
31
32
21
21
31
32
33
21
3433
35
12
32
21
21
27
34
35 28
30 = 6 X 12 MM
21 = 3.5 X 12 MM
English
English
English - 4
1) Open the carton of your new Turbo Hockey game near where you will play. Select a clear level floor. This
game requires at least two adults to assemble the table.
2) Remove all the contents from inside the carton and verify that you have all listed parts as shown on the
Parts Identifier. We suggest that you use the bottom carton as a clean flat working area to protect the
game. Carefully cut or tear the four carton corners so that the bottom is now your work area.
FIG. 1
3) Raise the Lower End Apron (#27). Turn the partially pre-installed Metal Plates (#29) upright. Attach the
top portion of the Metal Plate to the Lower End Apron with two (#30) Bolts using the 5mm Allen Key
(#16). Tighten securely at this time. Do the same for the other Lower End Apron. Note: the lower end
FIG. 2
5) Attach the two Apron Corners with Window (#32) to the two End and Side Aprons labeled "PLEASE
ATTACH APRON CORNER (#32) AT THIS SIDE" using eight (#21) Screws on the inside of each apron
corner (inside of the silver plastic piece). Next, attach the two Apron Corners (#31) to the other End and
Side Aprons. See Fig.2.
6) Place one Storage Door (#33) inside the Top Storage Drawer (#34) and attach one Bottom Storage
Drawer (#35) to the Top Storage Drawer (#34) using four (#21) Screws. See Fig. 2B. Then attach the
Drawer assembly (#33, 34 and 35) to the underside of playfield and the Apron Corners with window
(#32) using six (#21) Screws. See Fig.2 and 2A. Do the same for the other Drawer and Door.
ASSEMBLY INSTRUCTIONS:
We recommend that two adults work together to assemble this game.
apron must be placed inside of the molded
plastic connector. See Figures 1 and 1A.
4) Raise the Lower Side Apron (#28). Turn the
partially installed Metal Plates (#29) upright.
Attach the top portion of the Metal Plate to the
Lower Side Apron with two (#30) Bolts using
the 5mm Allen Key (#16) provided. Pilot holes
show the proper position. Do the same for the
other Lower Side Apron. Now go back and
tighten the bolts securely.
Lower Apron
Mold plastic
connector
SILVER
PLASTIC PIECE

©2005 KT Sports
FIG. 3
FIG. 3A
54
3
50
9
88
16
FIG. 3B
1
45
6
16
7
FIG. 3C
2
5
4
21
FIG. 3D
14
13
1536
21
13
18
14
13
18
16
54
7
7
6
6
1
1
1
1
6
6
7
8
9
21
50
= 18 MM
= 6 X 45 MM
= 4 X 40 MM
= 3.5 X 14 MM
= 22 MM
= 8 X 38 MM
English
English
English - 5
FIG. 3
7) Attach the Leg Support -B (#5) to the Leg Support -A (#4) using two (#50) Screws. Attach the supports
(#4, #5) to the Leg Support Base (#3) using four (#8) Bolts and four (#9) Washers per Leg Support Base
using the 5mm Allen Key (#16). See Fig. 3A. Repeat for each Leg. Do not tighten securely at this time.
8) Attach each leg support base assembly (#3, #4, #5) to each Leg (#1) using two (#6) Bolts and two (#7)
Washers per Leg using the 5mm Allen Key (#16). NOTE: Align the rounded corners of the Leg and the
sides of the leg support base assembly. See Fig. 3B. Now go back and tighten the bolts securely. Next,
attach the Leg Covers (#2) to each Leg (#1) using six (#21) Screws per leg. See Fig. 3C.
9) Attach one of the assembled legs to the table using four (#6) Bolts and four (#7) Washers per leg. See
Fig.3. Tighten securely with the 5mm Allen Key (#16). Do the same for the other three legs.
10) Screw one Leg Leveler (#18) into each leg. See Fig. 3. NOTE: Leg Levelers are optional and if the
game is to be used on a smooth floor, we recommend not installing them.
11) Attach one Puck Return Box w/trigger (#13) to Puck Return Tray (#15) using four (#21) Screws . See
Fig.3 and 3D. Pilot holes show the proper screw placement. Attach the pre-mounted Puck Catcher
Wires (#36) to the Puck Returns. See Fig. 3D. Do the same to attach the other Puck Return Box.

©2005 KT Sports
FIG. 4
FIG. 4A
12V DCADAPTOR
1000mA25W
47
37
44
14
20 = 3.5 X 25 MM
HOME
44
48
17
20
25
51
19
17
English
English
English - 6
HOLD TABLE
CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE
TABLE ON ITS LEGS!
FIG. 4
13) Attach the two Slide Scorer Assemblies (#19) on top of the side rails using two (#20) Screws per scorer
as shown Fig. 4. Pilot holes show the proper screw placement.
14). Install the Adjustable Goals (#17) by placing them into the pre-installed Adjustable Goal Anchors (#52).
See Fig.4
15) Plug the 12 DC Adaptor (#47) power cord into to the Control Box (#44). See Fig. 4A.
16) Plug the power cord into the power source, push the on/off switch (#48). You are now ready to play.
CAUTION: Two strong adults are recommended to turn
the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
12) Lift the table assembly from the floor with two strong adults, turn it over, and set table on its legs in
the location where you will play. Go back and make sure that all connections are tight.
CONTROL
BOX
CONTROL
WIRE

©2005 KT Sports
15
English
English
English - 7
NOTE: The scoreboard will shut off automatically after 20 minutes. If not in use, however, we
suggest turning the power off when the game will not be used for an extended period of time.
ELECTRONIC SCORER OPERATION:
1) Push the " scorer ON/OFF" the switch located on the side of the scoreboard to choose automatic scoring with
sound and light, or push the "Sound On/Off " switch to select automatic scoring without sound.
2) Each period is pre-set to 10 minutes and can be adjusted up or down by pressing the “+” or “-” buttons.
3) Press “Start” button to begin the game.
4) For a “time out” or dropped pucks, simply press the “Pause” button. Press the button again to restart the
game.
5) Each goal scored will be registered on the scoreboard and generate a crowd cheer. All scores can be cleared
by pressing the “Home Reset” or “Visitor Reset” buttons
6) The end of the 1st period will be signaled by a buzzer. Press the “Start” button to begin the 2nd period.
7) To reset the game, press the “+” and “-” buttons at the same time and hold for 2 seconds.
8). When the score for the home or visitor side reaches 99 in a period, press "pause" button then press "home/
reset" of "visitor/reset" to restart the point at "00", next press the "pause" botton and play again.
9). Note: Make sure the "on/off " switch is switched OFF on the control box, when you connecting or
replacing any plug or wire.
HOCKEY GAME RULES:
1) This game is designed to be played with two (2) players, one at each end, or with four (4) players, two at each
end of the game table.
2) Flip a coin to determine who will begin play, or a face-off can be held at the center of the table.
3) Play begins when the puck is placed on the playing surface. Players must hit the puck with the hand-held
pushers and attempt to shoot into the opponent’s goal.
4) One point is awarded when a puck is shot into the opponent’s goal.
5) Winning the game: the winning score is accomplished by being the first player to reach a predetermined score
or by being the player to score the most points within a given period.
MAINTAINING YOUR GAME:
1) Wipe playing surface with a clean cloth before and after each use.
2) While table is on, vacuum gently with a soft brush attachment on a vacuum cleaner.
3) In the event the puck becomes rough or scuffed, use a sheet of extra fine sand paper to lightly rub until the
puck is smooth.
4) For faster play, wipe down the playing surface with a spray wax and cloth. (NOTE: Do not spray the wax
directly on the table. Spray it on a cloth first.) Make sure the blower is on to prevent clogging the holes.
Come Explore our Website! (www.sportcraft.com) Join our mailing list to
receive more information on product updates and event announcements.
Or, complete your warranty registration on-line. You can even order
replacement parts, and learn more about our company.
SCHEMATIC DIAGRAM
THERMAL PROTECTOR CONNECTOR
SPT-2 POWER CORD
MOTOR
ON/OFF
SWITCH POLARIZED PLUG
AC 100-125V
ELECTRIC RATING : AC 100 -125 V, 50/60 HZ, 2 x 30/31 WATTS, 2850/3400 RPM
THERMAL PROTECTOR
MOTOR
Mt. Olive, NJ 07828
www.sportcraft.com
Printed in China

©2005 KT Sports
16
English
English
English - 8
**NOTE: Please save your original proof of purchase as it is needed should you require warranty service.
LIMITED WARRANTY
Limited Warranty
KT Sports (the “Company”) warrants the Product to be free from defects in workmanship and materials under normal use
and conditions FOR A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE in the United States and
Canada.
Product Registration Card
The Product Registration Card must be filled out completely and mailed to the Company at the address printed on the card
within 10 days from the date of your purchase of the Product.
What Is Covered
Except as provided below, this Limited Warranty covers all defects in materials and workmanship. This Limited Warranty
is void if the Product is:
• Damaged through improper usage, negligence, misuse, abuse, transportation damage, acts of nature, or accident
(including failure to follow the instructions supplied with the Product)
• Used in commercial applications or rentals
• Modified or repaired by anyone not authorized by the Company.
What Is Not Covered
This Limited Warranty does not cover expendable items such as batteries, light bulbs, fuses, accessories, cosmetic parts
and other items that wear out due to normal usage.
What The Company Will Pay For
If during the one year Limited Warranty period, any part or component of the Product is found by the Company to be
defective, the Company will, at its option, repair the Product, replace the Product with a new Product (either the same or
an equivalent model) or cause the original retailer of the Product to exchange the Product with a new Product (either the
same or an equivalent model) or refund the original purchase price of the Product, without charge for labor or parts. The
Company’s obligation to repair, replace or exchange the Product, however, shall be limited to the amount of the original
purchase price of the Product.
How To Obtain Warranty Service
In order to enforce your rights under this Limited Warranty, you must follow these procedures:
• You must have completed and mailed the Product Registration Card to the Company within 10 days of purchase of the
Product.
• You must include THE ORIGINAL COPY OF YOUR SALES RECEIPT.
• You must call the Company’s Consumer Service Department at 1-800-526-0244 from 9:00 A.M. to 5:00 P.M. (EST)
to notify the Company of the nature of the problem and to obtain instructions for how to obtain servicing. At the
Company’s option, the Product may be serviced at your location or at a location designated by the Company.
• If you are instructed to return the Product to the Company for servicing, you are responsible for shipping the Product,
at your expense, to the address designated by the Company in packaging that will protect against further damage.
• You must also include your name, address, daytime telephone number, model number of the Product and a description
of the problem.
• The Company will pay for any shipping charges to return the repaired or replaced Product to you.
THIS LIMITED WARRANTY IS AVAILABLE ONLY TO THE ORIGINAL PURCHASER OF THE PRODUCT AND IS VALID
IN THE UNITED STATES AND CANADA ONLY.
THE COMPANY’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR DO NOT ALLOW
FOR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. TO THAT EXTENT, THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
This Limited Warranty gives you specific legal rights, but you may also have other rights that vary from state to state.
If you have questions regarding this Limited Warranty or the operation of the Product, you may call or write us:
Consumer Service Department
313 Waterloo Valley Rd.
Mt. Olive, NJ 07828
1-800-526-0244
0504 TG

0905 - C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
9-3-34-012HG01
9-3-34-012HG02
9-3-34-074HG09
9-3-34-058HG01
9-3-34-058HG02
9-3-34-089HG05
9-3-27-093SC28
9-3-36-020HG09
9-3-27-093SC11
9-3-34-001HG05
9-3-34-001HG10
9-3-34-056HG51
9-3-34-040AHG06
9-3-34-015SC10
9-3-34-406HG07
9-3-34-091HG07
9-3-34-406HG08
9-3-34-086HG08
9-3-34-074HG04
9-3-27-080SC21
9-3-34-089HG13
9-3-34-058HG04
9-3-34-089HG16
9-3-34-058HG03
9-3-34-034-HG12
9-3-34-089HG14
9-3-34-058HG05
9-3-34-058HG06
9-3-34-082HG16
9-3-34-082HG17
9-3-34-012HG14
9-3-34-012HG15
9-3-34-012HG16
9-3-34-012HG17
9-3-34-012HG18
9-3-34-086HG19
9-3-34-406HG09
9-3-34-406HG10
9-3-34-406HG11
9-3-34-406HG12
9-3-34-406HG13
9-3-34-406HG14
9-3-34-406HG15
9-3-34-406HG16
9-3-34-406HG17
9-3-34-406HG18
9-3-34-004SC03
9-3-34-406HG19
9-3-34-040AHG11
9-3-34-012HG21
9-3-57-013HG02
9-3-00-001HG07
9-3-00-001HG08
REF QUANTITY
ORDERED PART # DESCRIPTION UNIT
PRICE TOTAL
AMOUNT
Subtotal:
NJ (6%), IL (6.25%), and CA (7.75%) Residents Add State Sales Tax:
Shipping and Handling Charges:
TOTAL:
$ 6.00 US
PARTS RE-ORDER FORM
# 2-1-57-013 HG - TURBO HOCKEY GAME
Send this form along with your
check or money order payable to:
Sportcessories
313 Waterloo Valley Road
Mt. Olive, NJ 07828
www.sportcraft.com
NAME: __________________________________________________ DATE: ______________________
ADDRESS: ___________________________________________________ PHONE: ____________________
CITY: ________________________________________ STATE: ____________ ZIP CODE: __________
Leg
Leg Cover
Leg Support Base
Leg Support - A
Leg Support - B
8 x 38mm Allen Key Bolt
22mm Flat Washer
6 x 45mm Allen Key Bolt
18mm Flat Washer
22 Gram Power Round Puck (Red)
Deluxe Power Pusher (Black)
Deluxe Power Pusher (Red)
Puck Return Box with Trigger
Forward Goal Trigger
Puck Return Tray with Screw
5mm Allen Key
Adjustable goal
6" Metal Leg Leveler
Die Cast Slide Scorer Assembly
3.5 x 25mm Wood Screw
3.5 x 14mm Washer Head Screw
Blower and Wire Connector
4 x 65mm Wood Screw
3 x 16mm Flat Head Screw
Name Plate
1.2x10mm Nail
Lower End Apron
Lower Side Apron
Metal Plate
6 x 12mm Allen Key Bolt
Apron Corner (Black)
Apron Corner with Window (Black)
Storage Door.
Top Storage Drawer (Black)
Bottom Storage Drawer (Black)
Puck Catcher Wire
Control Wire
Connecting Box
Scorer- Home with 18" Wire & Screw.
Scorer- Home with 43" Wire & Screw.
Scorer- Visitor with 18" Wire & Screw.
Scorer- Visitor with 43" Wire & Screw
Scorer- Clock with Wire & Screw
Control box with Screw
Connecting Wire
Scorer Base Box with Scorer
12V/ DC Adaptor
ON/OFF Switch
Puck Return Cover
4x40mm Flat Head Screw
Top Corner Cap (Black)
OPTIONAL ACCESSORIES:
Table Cover
Table Cover w/Kit (pucks/pushers/cleaner)
**NOTE: PRICES IN US DOLLARS AND SUBJECT TO CHANGE WITHOUT NOTICE.
10.00 ea
5.00 ea
8.00 ea
8.00 ea
8.00 ea
0.50 ea
0.50 ea
0.50 ea
0.50 ea
2.50 ea
5.00 ea
5.00 ea
3.00 ea
2.00 ea
3.00 ea
3.00 ea
8.00 ea
5.00 ea
6.00 ea
0.50 ea
0.50 ea
20.00 ea
0.50 ea
0.50 ea
2.00 ea
0.50 ea
8.00 ea
10.00 ea
0.50 ea
0.50 ea
6.00 ea
8.00 ea
4.00 ea
8.00 ea
8.00 ea
3.00 ea
3.00 ea
5.00 ea
15.00 ea
15.00 ea
15.00 ea
15.00 ea
15.00 ea
5.00 ea
3.00 ea
10.00 ea
10.00 ea
2.00 ea
3.00 ea
0.50 ea
3.00 ea
29.00 ea
35.00 ea