Sportsman KSPLIT10 User manual
KSPLIT10
GAS POWERED KINETIC
10 TON LOG SPLITTER INSTRUCTION MANUAL
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
This manual provides important information on proper operation & maintenance. Every effort has been
made to ensure the accuracy of this manual. These instructions are not meant to cover every possible
condition and situation that may occur. We reserve the right to change this product at any time without
prior notice.
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE,
DO NOT OPERATE THIS PRODUCT!
HAVE QUESTIONS? CONTACT US FIRST BEFORE CONTACTING THE RETAILER.
If you experience a problem, have questions or need parts for this product, call Customer Service at
1-866-460-9436, Monday-Friday, 8 AM - 4 PM Central Time. A copy of the sales receipt is required.
FOR CONSUMER USE ONLY – NOT FOR PROFESSIONAL USE.
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE WARRANTY FOR
FUTURE REFERENCE.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
2
SPECIFICATIONS COMPONENTS
•Max. Splitting Force: 10 Ton
•Max. Log Length: 20 inches
•Max. Log Diameter: 13.75 inches
•Max Load Weight: 100 lbs
•Horizontal position only
•4-Stroke OHV Engine 94cc
•Recoil Start
•2.7 HP Gasoline Engine
•Low Oil Shutdown
•EPA Approved
•Cycle Time: approx. 2 seconds
•Noise Level: 104dB @ 0% Load
•Oil Capacity: 12 ounces SAE10W-30
•Fuel Capacity: 0.42 gallon
•Fuel Type: Unleaded Gasoline Only 87 rating or higher
•Flywheel: 600 RPM
•Flywheel Weight: 15 lbs
•Spark Plug: E7RTC
•Spark Plug Gap: 0.6 - 0.8mm
•Hitch Pin not available/ This unit is non-towable
•Wheel/Tire Size: 8 x 1.75 inch
•Wedge Height: 7 inches
•Auto-Return
•Air-cooled engine
•High Altitude Use: This log splitter is not recommended for
high altitude use above 3,000 feet. This item may not function
properly above 3,000 feet because of air flow getting through
the mixer.
•Some assembly required. Outrigger Leg and Vee Belt
requires assembly.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
3
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
What You Need to Know About Safety Instructions
Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that
may occur. Common sense, caution and care must be exercised when operating or cleaning tools and equipment.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may
result in property damage.
2 YEAR LIMITED EMISSION-RELATED WARRANTY
THIS ENGINE MEETS U.S. EPA EMISSION STANDARDS UNDER 40 CFR 1054.625 .The emission-related limited warranty is valid for two (2)
years. Keep the purchase receipt and mail in the product registration card for proof of purchase. Buffalo Corp limits emission-related warranty
repairs to authorized service centers for owners located within 100 miles of an authorized service center. For owners located more than 100 miles
from an authorized service center, Buffalo Corp will, in its sole discretion, either pay for shipping costs to and from an authorized service center,
provide for a service technician to come to the owner to make the warranty repair, or pay for the repair to be made at a local non-authorized service
center. The provisions of this paragraph apply only for the contiguous states, excluding the states with high-altitude areas identified in 40 CFR part
1068, Appendix III.
To exercise this warranty, DO NOT RETURN TO RETAILER. Instead, call Customer Service toll free at 1-866-460-9436 (email address
info@buffalotools.com) and you will be instructed on where to take the engine for warranty service. Take the log splitter and proof of purchase (your
receipt) to the repair facility recommended by the Customer Service Representative. The warranty does not extend to log splitters damaged or
affected by fuel contamination, accidents, neglect, misuse, unauthorized alterations, use in an application for which the product was not designed
and any other modifications or abuse.
1 YEAR LIMITED WARRANTY (30 Day Limited Warranty for Commercial and Rental Purpose)
Log splitters are warranted to be free from defects in materials and workmanship for a period of 1 YEAR from date of original purchase. Buffalo Corp.
is not liable for any indirect, incidental or consequential damages from the sale or use of this product. Any implied warranties are limited to 1 YEAR
as stated, or as otherwise stated, in this written limited warranty. Some states do not allow the exclusion or limitation of incidental or consequential
damages. Some states do not allow limitation on the length of an implied warranty. Buffalo Corp will repair or replace, at its discretion, any part that
is proven to be defective in materials or workmanship under normal use during the 1 YEAR warranty period. Warranty repairs or replacements will
be made without charge for parts or labor. Parts replaced during warranty repairs will be considered as part of the original product and will have the
same warranty period as the original product. This warranty gives you specific legal rights, and you may have other rights that vary state to state.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
4
Notice Regarding Emissions:
Engines certified to comply with U.S. EPA emission regulations for SORE (Small Off Road Equipment) are certified to
operate on regular unleaded gasoline and may include the following emission control systems: Three-Way Catalyst
(TWC) (if equipped), and Engine Modifications (EM).
FIG A: NEVER PLACE YOUR HAND IN BETWEEN THE LOG, THE WEDGE AND THE RAM
FIG B: NEVER ATTEMPT TO CROSS SPLIT A LOG
T
h
i
s
i
s
a
h
i
g
h
-
p
o
w
e
r
e
d, gasoline fuel powered
m
a
c
h
i
n
e
,
w
it
h
m
o
v
i
n
g
p
a
r
t
s
that produce
h
i
g
h
e
n
e
r
g
y
.
Operate
t
h
e
m
a
c
h
i
n
e
s
a
f
e
l
y
to avoid injury
.
U
n
s
a
f
e
o
p
e
r
a
ti
o
n
c
a
n
c
r
e
a
t
e
a
n
u
m
b
e
r
o
f
h
a
z
a
r
d
s
f
o
r
y
o
u
,
a
s
w
e
ll
a
s
a
n
y
o
n
e
e
l
s
e
i
n
t
h
e
n
e
a
r
b
y
a
r
e
a
.
View all WARNING and operating instruction labels on your machine before each use. Below are copies of all the safety
and information labels that appear on the equipment. Read and understand them before use to prevent injuries.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
5
IMPORTANT SAFETY INSTRUCTIONS
STOP!
Before using this log splitter and if you have any questions regarding the hazard and safety notices listed in this manual and/or on this
log splitter, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time.
Carbon Monoxide Gas: When in operation, the exhaust from this log splitter contains poisonous carbon monoxide gas. Carbon monoxide gas is
both odorless and colorless AND may be present even if you do not see or smell gas. Breathing this poison gas can lead to headaches, dizziness,
drowsiness, loss of consciousness and eventually death.
WARNING: USE THIS LOG SPLITTER ONLY OUTDOORS IN NON-CONFINED AREAS. DO NOT SECURE THE LOG SPLITTER WITH A
CHAIN OR ROPE, AS THIS WILL MAKE IT DIFFICULT TO MOVE IN AN EMERGENCY.
• Keep at least several feet of clearance on all sides to allow proper ventilation for this log splitter.
WARNING: CALIFORNIA PROP 65: According to the State of California, engine exhaust and some of its constituents from this generator are know
to contain chemicals known to cause cancer, birth defects, or other reproductive harm.
WARNING: CALIFORNIA PROP 65: According to the State of California, this product contains or emits chemicals known to cause cancer, birth
defects and other reproductive harm.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
6
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
7
A
l
w
a
y
s
t
a
k
e
t
h
e
f
o
ll
o
w
i
n
g
p
r
e
c
a
u
ti
o
n
s
w
h
e
n
u
s
i
n
g
t
h
i
s
m
a
c
h
i
n
e
:
•Allow only one person to operate the Log Splitter at any time.
•
The
o
p
e
r
a
t
o
r
o
r
u
s
e
r
i
s
r
e
s
p
o
n
s
i
b
l
e
f
o
r
a
cc
i
d
e
n
t
s
o
r
h
a
z
a
r
d
s
o
cc
u
rr
i
n
g
t
o
o
t
h
e
r
p
e
o
p
l
e
,
t
h
e
i
r
p
r
o
p
e
r
t
y
,
a
n
d
t
h
e
m
s
e
l
v
e
s
.
•
Wear
p
r
o
t
e
c
ti
v
e
g
o
gg
l
e
s
o
r
s
a
f
e
t
y
g
l
a
ss
e
s
w
it
h
s
i
d
e
s
h
i
e
l
d
s
w
h
i
l
e
u
s
i
n
g
t
h
e
l
o
g
s
p
l
itt
e
r
t
o
p
r
o
t
e
c
t
y
o
u
r
e
y
e
s
f
r
o
m
p
o
ss
i
b
l
e
t
h
r
o
w
n
d
e
b
r
i
s
.
•
Av
o
i
d
w
e
a
r
i
n
g
l
oo
s
e
c
l
o
t
h
i
n
g
o
r
j
e
w
e
l
r
y
,
w
h
i
c
h
c
a
n
c
a
t
c
h
o
n
m
o
v
i
n
g
p
a
r
t
s
.
•
Wear
g
l
o
v
e
s
w
h
i
l
e
u
s
i
n
g
t
h
e
l
o
g
s
p
l
itt
e
r
.
B
e
s
u
r
e
y
o
u
r
g
l
o
v
e
s
f
it
p
r
o
p
e
r
l
y
a
n
d
d
o
n
o
t
h
a
v
e
l
oo
s
e
c
u
ff
s
o
r
d
r
a
w
s
t
r
i
n
g
s
.
•
W
e
a
r
s
ho
e
s
w
it
h
n
o
n
-
s
l
i
p
t
r
e
a
d
s
w
h
e
n
u
s
i
n
g
y
o
u
r
l
o
g
s
p
l
itt
e
r
.
I
f
y
o
u
h
a
v
e
s
a
f
e
t
y
s
ho
e
s
,
w
e
r
e
c
o
mm
e
n
d
w
e
a
r
i
n
g
t
h
e
m
.
D
o
n
o
t
u
s
e
t
h
e
m
a
c
h
i
n
e
w
h
i
l
e
b
a
r
e
f
oo
t
o
r
w
e
a
r
i
n
g
o
p
e
n
t
o
e
d
s
a
n
d
a
l
s
.
•
W
e
a
r
l
o
n
g
p
a
n
t
s
w
h
i
l
e
o
p
e
r
a
ti
n
g
t
h
e
l
o
g
s
p
l
itt
e
r
.
•
K
ee
p
children, pets and
b
y
s
t
a
n
d
e
r
s
a
t
l
e
a
s
t
50
f
ee
t
a
w
a
y
f
r
o
m
y
o
u
r
w
o
r
k
a
r
e
a
a
t
a
ll
ti
m
e
s
.
S
t
o
p
t
h
e
m
o
t
o
r
w
h
e
n
a
n
o
t
h
e
r
p
e
r
s
o
n
o
r
p
e
t
a
pp
r
o
a
c
h
e
s
.
N
e
v
e
r
a
ll
o
w
c
h
i
l
d
r
e
n
t
o
o
p
e
r
a
t
e
t
h
e
l
o
g
s
p
l
itt
e
r
.
•
Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and
open flame, and out of the reach of children.
•
Replace rubber fuel lines and grommets when worn or damaged and after 5 years of use.
•
Fill the gasoline tank outdoors with the engine off and allow the engine to cool completely. Don't handle gasoline if
you or anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode. Reinstall the fuel
tank cap and fuel container cap securely.
•
If you spill gasoline, do not attempt to start the engine. Move the machine away from the area of the spill and avoid
creating any source of ignition until the gas vapors have dissipated. Wipe up any spilled fuel to prevent a fire hazard
and properly dispose of the waste.
•
Allow the engine to cool completely before storing in any enclosure. Never store a machine that has gas in the tank,
or a fuel container, near an open flame or spark such as a water heater, space heater, clothes dryer or furnace.
•
Never make adjustments or repairs with the engine running. Shut down the engine, disconnect the spark plug wire,
keeping it away from the spark plug to prevent accidental starting, wait 5 minutes before making.
•
Never tamper with the engine’s governor setting. The governor controls the maximum safe operation speed and
protects the engine. Over-speeding the engine is dangerous and will cause damage to the engine and to the other
moving parts of the machine.
•
Keep combustible substances away from the engine when it is hot.
•
Never cover the machine while the muffler is still hot.
•
Do not operate the engine with the air cleaner or the carburetor air intake cover removed. Removal of such parts
could create a fire hazard. Do not use flammable solutions to clean the air filter.
•
The muffler and engine become very hot and can cause a severe burn; do not touch.
N
o
l
i
s
t
o
f
w
a
r
n
i
n
g
s
a
n
d
c
a
u
ti
o
n
s
c
a
n
b
e
a
ll
-
i
n
c
l
u
s
i
v
e
.
I
f
s
it
u
a
ti
o
n
s
o
cc
u
r
t
h
a
t
a
r
e
n
o
t
c
o
v
e
r
e
d
b
y
t
h
i
s
m
a
n
u
a
l
,
t
h
e
o
p
e
r
a
t
o
r
m
u
s
t
apply common sense and operate this log splitter in a safe manner.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
8
ASSEMBLY DIAGRAM
Some assembly required. Please identify components below. Vee-belt, pulley guard and outrigger leg will require assembly.
When installing belt, make sure it can be pressed down Place the Pulley Guard over the belt, then attach the two
0.75 – 1.25 inches (2~3 cm) when assembled. bolts securely.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
9
ASSEMBLY COMPONENTS
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
10
ASSEMBLY COMPONENTS
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
11
PREPARING THE LOG SPLITTER FOR USE
STOP!
The following section describes the required steps for preparing this log splitter for the first use. Failure to correctly perform these steps can damage
this log splitter and/or shorten its life. If still unsure about how to perform any of these steps after reading this section, call
1-866-460-9436 Monday - Friday, 8 AM - 4 PM Central Time for customer service.
Step 1 - Add Oil
THIS LOG SPLITTER REQUIRES AT LEAST 12 OUNCES OF OIL (SAE10W-30) TO RUN.
ADD OIL UNTIL IT IS ALMOST OVERFLOWING. THE LOW-OIL SENSOR IS VERY SENSITIVE AND THE ENGINE
WILL NOT RUN IF THE OIL IS LOW. START WITH 12 OUNCES, THEN ADD MORE UNTIL ALMOST OVERFLOWING.
TROUBLESHOOTING: IF THE LOG SPLITTER WILL NOT START, DOUBLE CHECK THAT THE OIL LEVEL IS
COMPLETELY FULL AND ALMOST OVERFLOWING.
This log splitter requires engine oil to function. Engine oil is a major factor affecting engine performance and
service life. When new from the package,this log splitter contains no oil in the engine crankcase. Add oil before
operating this log splitter for the first time. When replenishing oil for subsequent use of this log splitter, always determine
that this log splitter has the correct quantity of oil. To add oil to the engine crankcase:
1. Confirm that this log splitter is on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine as illustrated in Figure 1 below. (NOTE: There are two locations to
add oil (see Figure 1). You can choose to use either one.)
3. Using a funnel, add high detergent motor oil to fill the engine crankcase to the correct quantity. SAE10W-30 oil is
recommended for general use. When the engine crankcase is full and almost overflowing, the oil level should reach the
lower lip of the oil filling opening as shown in Figure 2.
4. Replace the oil filler/dipstick cap and close the oil access panel.
5. (Figure 3 indicates the location to drain oil, if necessary)
Figure 1 – Unscrew Either Dipstick CapsFigure 2 - Add Oil Figure 3 - Drain Oil (when necessary)
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
12
Step 2 - Add Gasoline
Gasoline and gasoline fumes are highly flammable and explosive. Handling fuel can result in serious injury or
burns.
• Do not fill the fuel tank near a heat, sparks or an open flame. Keep gasoline away from appliance pilot lights, barbecues,
electric appliances, power tools, etc.
• Do not overfill the fuel tank. Always check for fuel spills and immediately wipe them up. Spilled fuel is a fire hazard and
causes environmental damage.
To add gasoline:
To ensure that this log splitter runs smoothly, use only FRESH, UNLEADED GASOLINE WITH AN OCTANE RATING OF
87 OR HIGHER. Unleaded gasoline produces fewer engine and spark plug deposits and extends the life of the exhaust
system.
1. Confirm that this log splitter is on a level surface.
2. Unscrew fuel tank cap and set aside. (NOTE: The fuel tank cap may be tight and difficult to unscrew.)
3. Slowly add fresh, unleaded gasoline (with an octane rating 87 or higher) to the fuel tank. Be careful not to fill the fuel
tank above the upper limit line. NOTE: Because gasoline can expand, do not fill the fuel tank to the very top.
4. Securely tighten the fuel tank cap and immediately wipe up any spilled gasoline with a dry cloth.
Fuel Tank Capacity (gallons)
0.42
Fuel Type
Fresh, Unleaded Gasoline Octane Rating 87 or Higher
IMPORTANT:
• Use only UNLEADED gasoline with an octane rating of 87 or higher.
• Never use a mixture of oil and gasoline.
• Never use old and/or contaminated gasoline.
• Avoid getting dirt and/or water in the fuel tank.
• Gasoline can age in the fuel tank and make it difficult to start this log splitter. Never store this log splitter for extended
time with gasoline in the fuel tank.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
13
STARTING THE LOG SPLITTER
Before starting the log splitter, confirm that all steps in the section titled, “Preparing the Log Splitter for Use,” of this manual have been completed.
If unsure about how to perform any of these steps, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time for customer service.
To start this log splitter:
1. Be certain gasoline and oil have been added. Turn the fuel valve to the “on” position. Figure 4A
2. Move the choke lever to the “Closed/Choke” position. Figure 4B.
3. Set the engine switch to the “on” position Figure 4C.
4. Slowly pull on the recoil starter handle, shown in Figure 4D, until a slight resistance is felt. Then pull briskly to start the engine. Gently return the
cord into the log splitter to avoid damage to the starter or housing. Never allow the cord to snap back.
5. If the engine fails to start, repeat step 4. After repeated attempts to start the engine, consult the troubleshooting guide before attempting again.
6. Once the engine has started, GRADUALLY move the choke lever to the “Open/Run” position until the engine levels off. Then let the engine run
approximately 5 minutes BEFORE adding appliances or tools. Adjust the speed using the Throttle Figure 4E.
Fuel Cock
The fuel cock is located between the fuel tank and carburetor. When the fuel cock is in the ON position, fuel is allowed to flow from the fuel tank to
the carburetor. Be sure to return the fuel cock to the OFF position after stopping the engine.
Choke Rod
The choke is used to provide an enriched fuel mixture when starting a cold engine. It can be opened and closed by operating the choke rod
manually. Pull the rod out toward CLOSED to enrich the mixture for cold starting.
STOPPING THE LOG SPLITTER
1. Turn the Fuel Valve to the “OFF” position.
2. Set the Engine Power Switch to the “OFF” position.
Allow this log splitter to cool down before touching areas that become hot during operation.
Allowing gasoline to sit in this log splitter fuel tank for extended time without use can increase the difficulty in starting in
the future. Never store this log splitter for extended time with gasoline in the fuel tank.
Figure 4D The Recoil Start
Figure 4A Fuel Valve
Figure 4C Engine Switch
Figure 4B Closed / Choke
Figure 4E Throttle
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
14
OPERATION INSTRUCTIONS
The
diameter
listed
is
indicative
of
the
maximum suggested
size.
A
small
log
can
be
difficult
to
split when
it
contains
knots
or
a
particularly
tough
fiber. However,
it
may
not
be
difficult
to
split logs
with
regular
fibers
even
if
its
diameter
exceeds the
maximum
indicated
above.
•Max. Log Length: 20 inches
•Max. Log Diameter: 13.75 inches
•
N
e
v
e
r
a
tt
e
m
p
t
t
o
s
p
l
it
w
oo
d
a
c
r
o
ss
t
h
e
g
r
a
i
n
.
T
h
e
L
o
g
S
p
l
itt
e
r
w
a
s
n
o
t
d
e
s
i
g
n
e
d
f
o
r
c
r
o
ss
-
g
r
a
i
n
s
p
l
itti
n
g
.
D
o
i
n
g
s
o
c
o
u
l
d
d
a
m
a
g
e
t
h
e
L
o
g
S
p
l
itt
e
r
a
n
d
m
a
y
c
a
u
s
e
p
e
r
s
o
n
a
l
i
n
j
u
r
y
.
•
M
a
k
e
s
u
r
e
b
o
t
h
e
n
d
s
o
f
t
h
e
l
o
g
y
o
u
a
r
e
s
p
l
itti
n
g
a
r
e
c
u
t
a
s
s
q
u
a
r
e
a
s
p
o
ss
i
b
l
e
.
T
h
i
s
w
i
ll
p
r
e
v
e
n
t
t
h
e
l
o
g
f
r
o
m
s
l
i
d
i
n
g
o
u
t
o
f
p
o
s
iti
o
n
w
h
i
l
e
u
n
d
e
r
p
r
e
ss
u
r
e
.
THE KINETIC LOG SPLITTER OPERATES DIFFERENTLY THAN A HYDRAULIC SPLITTER. OPERATE THE
MACHINE PROPERLY OR RISK DAMAGE TO THE MACHINE. ALWAYS FOLLOW THESE NOTICES:
•The Engagement Handle should be engaged in rapid movement in order for the Rack and Pinion to engage and
disengage fully without damage.
•
Do not stop t
h
e
E
n
g
a
g
e
m
e
n
t
H
a
n
d
l
e
i
n
a
n
y
l
o
c
a
ti
o
n
b
e
t
w
ee
n
t
h
e
f
u
ll
y
f
o
r
w
a
r
d
o
r
f
u
ll
y
b
a
c
k
w
a
r
d
p
o
s
iti
o
n
s
.
•
D
o
n
o
t
ho
l
d
t
h
e
H
a
n
d
l
e
i
n
t
h
e
f
o
r
w
a
r
d
p
o
s
iti
o
n
w
h
e
n
t
h
e
R
a
m
s
t
o
p
s
m
o
v
i
n
g
f
o
r
w
a
r
d
.
A
l
w
a
y
s
p
u
ll
t
h
e
E
n
g
a
g
e
m
e
n
t
H
a
n
d
l
e
R
A
P
I
D
L
Y
t
o
t
h
e
b
a
c
k
(
A
u
t
o
-
R
e
t
r
a
c
t
)
p
o
s
iti
o
n
a
s
s
oo
n
a
s
t
h
e
L
o
g
i
s
s
p
l
it
o
r
w
h
e
n
t
h
e
R
a
m
i
s
a
t
t
h
e
e
n
d
o
f
t
h
e
s
t
r
o
k
e
o
r
w
h
e
n
t
h
e
R
a
m
s
t
o
p
s
m
o
v
i
n
g
f
o
r
w
a
r
d
du
e
t
o
a
t
o
u
g
h
l
o
g
.
1. Place the log on the Log Splitter. Grasp the log on the sides near the middle of the block. Center the log, side-to-side,
on the rail of the Log Splitter, making sure that one end is against the Splitting Wedge.
2. The engagement Handle must be held fully in the Split Position against the hard stop when splitting. Failure to do so
may result in kickback of the Handle.
3. Move the Operation Handle from Lock to Unlock, then the other hand Rapidly moves the Engagement handle
4. IMMEDIATELY AFTER the log is split, actuate and hold the Engagement Handle to the Auto-Retract position to allow
the Ram to return. If the Ram stops before the end of the stroke while splitting a tough log, quickly actuate the
Engagement Handle back to the Auto-Retract position.
Splitting Tough Logs
If the Ram stops before the end of the stroke while splitting a tough log, quickly actuate the Engagement Handle back to
the Auto-Retract position. Let the Ram return and allow the flywheels to gain momentum for another full power split.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
15
MAINTENANCE CHECKLIST
P
R
O
C
E
D
U
RE
Before each use
Every 5 hours
Every 25 hours
Every 100 hours
C
h
e
c
k
engine oil level
Δ
Check general equipment
Δ
Grease surface of slide
rail
Δ
Check belts
Δ
G
r
e
a
s
e
R
a
c
k and pinion
Δ
Clean engine exterior and
cooling
Δ
Change engine oil
First time 5 hours
Δ
Replace air filter
Δ
Replace spark plug
Δ
Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
Cleaning the Log Splitter
Always try to use this log splitter in a cool dry place. If this log splitter becomes dirty, the exterior can be cleaned with a
damp cloth, soft brush, vacuum and/or pressurized air.
Never clean this log splitter with a bucket of water and/or a hose as water can get inside and cause a short circuit or
corrosion.
Never use gasoline to clean parts of this log splitter.
Checking the Oil Level
It is important to check the oil level in the engine crankcase before each use to ensure that there is a sufficient quantity.
To check the oil level:
1. Verify that this log splitter is shut down and on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine.
3. With a dry cloth, wipe the oil off of the dipstick that is located on the inside of the cap.
4. Insert the dipstick as if replacing the cap and then remove again. There should be oil on the dipstick. If there is no oil on
the dipstick, or oil is visible only at the very end of the dipstick, add oil until the engine crankcase is filled.
5. Confirm that the oil filler/dipstick cap is properly in place when finished verifying the oil level.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
16
Changing/Adding Oil
The oil level in this log splitter should be checked before each use. If oil level is low, add oil until the level is sufficient to
operate. (See Figure 2.) The oil should be changed after the first 20 hours of operation. Subsequently, the oil should be
changed every 6 months, or for every 100 hours of use, or when the oil has become contaminated with water and/or dirt.
To drain the oil from this log splitter:
1. Place a bucket underneath this log splitter to catch oil as it drains.
2. Unscrew the oil drain plug located on the crankcase using 10 mm hex wrench. (See Figure 3.)
3. Allow all the oil to drain from this log splitter.
4. Replace the oil drain plug and tighten using 10 mm hex wrench. (See Figure 3.)
NOTE: Never dispose of used motor oil in the trash, down a drain or on the ground. Put oil in a sealed container and
contact your local recycling center or auto garage to arrange oil disposal.
Air Filter Maintenance
Routine maintenance of the air filter helps maintain proper airflow to the carburetor. Occasionally verify that the air filter is
free of excessive dirt. The air filter will require frequent cleaning when operating this log splitter in extremely dusty areas.
1. To clean the air filter, remove the foam filter element from the log splitter and wash it in warm water and household dish
detergent. Thoroughly rinse and dry. Pour a small amount of motor oil onto the filter, ring out ALL excess oil, and reinstall
the foam filter element in the log splitter.
2. Unscrew the bolts, or unsnap the clips at the top and bottom of the air filter cover, located below the choke lever, to
access foam filter element.
Spark Plug Maintenance
The spark plug is essential for proper engine operation. The spark plug should be intact, free of deposits, and properly
gapped. A bad or incorrectly installed spark plug can cause engine damage. To inspect the spark plug:
1. Remove the spark plug by pulling on the spark plug cap.
2. Unscrew the spark plug from this log splitter by using the included spark plug wrench.
3. Visually inspect the spark plug. If it is cracked and/or chipped, discard and install a new spark plug. Using a E7RTC
spark plug, such as NGK BP6HS, is recommended.
4. Measure the spark plug electrode gap with a gauge. The gap should be 0.024-0.031in (0.6-0.8mm). (See Figure 9.)
5. If re-using the spark plug, use a wire brush to clean dirt from around the spark plug base and then re-gap the plug.
6. Screw the spark plug back into place on this log splitter by using the included spark plug wrench.
7. Replace the spark plug cap.
Figure 9 - Measuring the
spark plug gap
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
17
To store this log splitter for extended time, drain the gasoline from the carburetor AND fuel tank.
To drain gasoline from this log splitter:
1. Turn the fuel valve to the “off” position and let the engine run until it stops.
2. Remove the fuel filter cup.
3. Empty the fuel filter cup of any fuel.
4. Place a receptacle underneath this log splitter to catch gasoline as it drains.
5. Turn the fuel valve to the “on” position and allow all gasoline to drain.
6. Turn the fuel valve to the “off” position.
7. Replace the fuel filter cup.
8. Store the drained gasoline in a suitable place.
To store this log splitter for extended time, the fuel needs to be drained from the carburetor.
To drain the gasoline from the carburetor turn the fuel valve to the “off” position while the engine is running. The log
splitter will shut down when all the gasoline in the carburetor has been used.
Do not store gasoline for more than 3 months.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
18
TROUBLESHOOTING
IMPORTANT: If trouble persists, call our customer help line at 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time.
SYMPTOM
POSSIBLE CAUSE
The engine won’t start.
⇒Is the ignition switch in the “ON” position?
⇒Is the fuel shut-off valve on?
⇒Are you using fresh, clean gas? If the gas is old, change it. Use
a fuel stabilizer if you keep gas longer than 30 days.
⇒Is the spark plug clean? If the spark plug is dirty or cracked, change it.
If it’s oily, leave it out, hold a rag over the plug hole and pull the recoil
cord several times to blow out any oil in the cylinder, then wipe off the
plug and reinsert it.
The engine lacks power
or is not running
smoothly.
⇒Check that the Throttle Lever is in the “Run” position.
⇒Is the air filter clean? If it’s dirty, change it following the procedure in
the engine manufacturer’s owner’s manual.
⇒Is the spark plug clean? If it’s fouled or cracked, change it. If it’s oily,
leave it out, hold a rag over the plug hole and pull your recoil cord
several times to blow out any oil in the cylinder, then wipe off the plug
and reinsert it.
⇒Are you using fresh, clean unleaded gas? If it’s old, change it. Use a
fuel stabilizer if you keep gas longer than 30 days.
⇒Does your engine have the right amount of clean oil? If it’s dirty,
change it following the procedure in the engine manufacturer’s
owner’s manual.
⇒Check the oil level and adjust as needed.
Engine smokes.
(Please refer to the
engine user manual
for engine-specific
procedures.)
⇒Check the oil level and adjust as needed.
⇒Check the air filter and clean or replace if needed.
⇒You may be using the wrong oil—too light for the temperature. Refer to
your Engine Owner’s Manual for detailed information.
⇒Clean the cooling fins if they’re dirty.
Rack catching on tail
tube (at end of stroke).
Rack returning very slow
or not going all the way
back.
⇒Adjust carriage hold downs (slide guides).
⇒Check for wood chips or debris between ram bushing plate and beam.
⇒Check rack lift bearing for alignment or damage.
⇒Return spring is unhooked or damaged. Reconnect or replace as
needed.
⇒Machine wedge end too low. Must be almost level or wedge end
slightly higher.
Operator Lever
Snapping out of gear or
not staying in gear.
⇒Lever not all the way forward when rack comes under full load.
Push lever quicker and more forcefully into the full forward position.
⇒Ram has been overloaded at lower part of face. Check rack gear for
straightness.
Rack slamming back too
fast.
⇒Wedge end of machine too high. Must be almost level with ram
end or just slightly higher.
⇒Springs not operating properly. Fix or replace as needed.
Machine does not seem
to have full splitting power.
⇒The belts may be too loose and slipping. Adjust or replace belts as
needed.
Operator Lever not
engaging rack with
pinion gear.
⇒Clean wood chips or other debris from under rack.
⇒Clean accumulated dirt from frame where carriage assembly rests
against rubber bumpers.
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
19
PARTS DIAGRAM
‘
KSPLIT10 GASOLINE POWERED KINETIC LOG SPLITTER INSTRUCTION MANUAL
20
PARTS LIST
No.
Description
Qty
No.
Description
Qty
1
Body
1
29
Hex bolt M8x30
3
2
Bearing 6201
2
30
Key 6x6
1
3
Flat Washer φ12
8
31
Flat washerφ8
3
4
Hex Bolt M12x115
2
32
Engine pulley
1
5
Nylon slider
1
33
Hex bolt M10x30
16
6
Pusher
1
34
Spring washer φ10
12
7
Rack
1
35
Engine
1
8
Spring
1
36
Engine support
1
9
Restoration device
1
37
Flywheel guard
1
10
Hex Bolt M12x45
2
38
Flywheel
1
11
Flat Washer φ10
36
39
Key 8x7
2
12
Hex Bolt M10x45
6
40
Pinion driver
1
13
Hex Bolt M8x35
1
41
Bearing housing
2
14
Flat Washer φ8
6
42
Pulley guard
1
15
Screw M12
3
43
Flywheel for belt
1
16
Short Bushing
2
44
V belt
1
17
Long Busher
1
45
Outrigger leg
1
18
Screw M10
12
46
Hex bolt M6x16
1
19
Screw M8
1
47
Side roller fitting
2
20
Bearing 628
1
48
Hex bolt M8x15
4
21
Splitting handle
1
49
Spring washerφ8
4
22
Press device
1
50
Hex bolt M10x90
2
23
Sleeve
1
51
Side roller
2
24
Hex Bolt M12x65
1
52
Flat washer φ12
2
25
Roller
1
53
Wheel
2
26
Lock-Unlock handle
1
54
Tension spring
1
27
Lock-Unlock device
1
55
Wheel bracket
1
28
Hex Bolt M10x80
1
56
Cotter pinφ3.2
2
Table of contents
Other Sportsman Log Splitter manuals
