power King PK0322 Manual

22 TON 3PT LOGSPLITTER
MODELS PK0322
Owner’s Manual and Operating Instructions

2
OPERATION INSTRUCTIONS
Proper Operation of the Log Splitter
1.) Load a log onto the beam and against the endplate.
2.) Serious accidents can happen when other people are allowed inside the work zone. Keep
everyone else out of the work zone while operating control valve.
3.) Make sure hands are clear of crush hazard zones.
4.) Push control valve handle FORWARD by two hands to split log.
5.) Push control valve handle BACKWARD by two hands to return wedge to its original position.
6.) Clear the split wood from the work zone.
！

3
OPERATION INSTRUCTIONS
！
WORK IN HORIZONTAL
WORK IN VERTICAL

4
OPERATION INSTRUCTIONS
HOW TO SPLIT THE LOG WITH SLANT SURFACE
！

5
Components in the package

6
Open Shipping Crate
1. Set the shipping Crate on a solid, flat surface.
2. Carefully cut the shipping bands and remove lid of shipping crate.
3. Using two people to lift, carefully remove the engine, oil tank, wheels, tow bar, support legs, and
hardware. (For parts reference see the last page in manual)
4. Locate all hardware before beginning assembly.
Step 1: Outrigger leg Assembly Step 2: Outrigger leg Assembly
ASSEMBLY
assemble the left and right outrigger leg in
proper position.and fix with bolt and lock nut as
per picture.
Upright the beam, and assemble the left and
right outrigger leg in proper position.and fix
with bolt and lock nut as per picture.

7
Assemble control valve on cylinder
Step 3: Assemble the bracket
Step 4: Assemble the control valve Step 5: Assemble the pipe
Assemble the long and short bracket fixed with bolt and lock nut. As per picture.
Take off the safe pin and put down the beam support
Assemble the three hydraulic pipe as per the
mark on it properly

8
Step 6: Assemble the log cradle and handle
Assemble the log cradle on beam fixed with bolt and lock nut.
Assemble the handle on beam in proper postion

9
EXPLODED VIEW AND PARTS LIST

10
No. Description Qty No. Description Qty
1 Base plate 1 28 Screw M10 20
2 Hex screw M12x40 4 29 Handle grip 1
3 Wedge wing(left) 1 30 Handle lever 1
4 Wedge 1 31 Hinge Pin 1
5 Hex bolt M12x45 10 32 Cylinder lock pin 1
6 Wedge wing (right) 1 33 Safety chain 1
7 screw M12 15 34 Returning spring 1
8 Track slab 2 35 Flat washer φ20 1
9 Flat washer φ12 10 36 Shaft Circlip φ19 1
10 1/2”-3/4” Corner Connector 1 37 Pin φ19 1
11 Hydraulic pipe B 1 38 Bolt M10x75 8
12 Pipe Connector 1 39 Flat washer φ8 16
13 Control vavle 1 40 Bolt M8x25 8
14 1/2”-1/2” Corner Connector 3 41 Outrigger leg(left) 2
15 Screw M8 10 42 Outrigger leg(right) 2
16 Hydraulic pipe C 1 43 Horizontal bracket(short) 2
17 Hydraulic pipe A 1 44 Horizontal bracket(long) 2
18 Screw M12x55 1 45 Spring washer φ8 8
19 cylinder 1 46 Nut M22x1.5 2
20 Rpin φ3x73 2 47 Srping washerφ22 2
21 Bolt M10x25 12 48 Pin φ22 2
22 Spring washer φ10 16 49 O type lock pin φ11x45 3
23 Flat washer φ10 44 50 3 point support 1
24 Log stripper reinforced plate 1 51 Log cradle 2
25 Log stripper (left) 1 52 Control Valve Operating instruction
Plate 1
26 Log stripper (right) 1 53 Bolt M8x40 2
27 Bolt M10x30 4 54
QVTOOLS, LLC.