Sportsman GEN3000IOF User manual

ITEM # GEN3000IOF
3000 Surge Watts / 2850 Running Watts
GAS FUEL INVERTER GENERATOR INSTRUCTION MANUAL
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
This manual provides important information on proper operation & maintenance. Every effort has been
made to ensure the accuracy of this manual. These instructions are not meant to cover every possible
condition and situation that may occur. We reserve the right to change this product at any time without
prior notice.
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE,
DO NOT OPERATE THIS PRODUCT!
If you experience a problem, have questions or need parts for this product, call Customer Service at
1-866-460-9436, Monday-Friday, 8 AM - 4 PM Central Time. A copy of the sales receipt is required.
FOR CONSUMER USE ONLY – NOT FOR PROFESSIONAL USE.
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE WARRANTY FOR FUTURE
REFERENCE.
Visit our website for Troubleshooting / Frequently Asked Questions
http://sportsmanseriesbrand.com/generators
X

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
2
GEN3000IOF Portable Gas Fuel Inverter Generator
FEATURES:
•3000 Surge Watts / 2850 Running Watts
•4-Stroke OHV Engine 208cc
•Recoil Start
•5.5 HP Gas Fuel Engine
• 2 - 120V A/C Outlets
• 1 - 120V RV Outlet
• 2 – USB Outlets
•Engine Run Time: 8 Hours @ 50% Load
•Low Oil Shutdown
•Sine Wave Output
•Parallel Port Outlet Capability
•EPA Approved
•Noise Level: 65dB @ 0% Load
•Oil Capacity: 20.2 ounces
•Fuel Capacity: 3.1 gallon
•Fuel Type: Unleaded Gasoline Only 87 rating or higher
•3,800 RPM
•Mobility Kit: Not Available
•If you are using a generator 3,000 feet above sea level, it may not function properly because of air flow getting through the carburetor.
•High Altitude Use: This generator is not recommended for high altitude use above 3,000 feet.
AC Output
Rated Voltage (V)
120
Rated Watts (W)
2850
Rated Frequency (Hz)
60
Phase
Single
USB Output
Voltage (V)
5V 2.1A
Engine
Engine Type
4-stroke single cylinder with forced air cooling system
Ignition System
Non-contact transistor (C.D.I.)
Starting System
Recoil

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
3
TABLE OF CONTENTS
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS...............................................................................................4
PACKAGE CONTENTS
PACKAGE CONTENTS ...........................................................................................................................................9
COMPONENTS .....................................................................................................................................................10
PREPARING THE GENERATOR FOR USE ....................................................................................................................11
Using This Generator For The First Time...............................................................................................................11
Step 1 – Add Oil ............................................................................................................................................11
Step 2 – Add Gasoline ..................................................................................................................................12
Step 3 – Ground The Generator....................................................................................................................12
Subsequent Use Of This Generator.......................................................................................................................13
Step 1 – Verify Oil Level................................................................................................................................13
Step 2 – Verify Gas Level..............................................................................................................................13
Step 3 – Ground The Generator....................................................................................................................13
STARTING THE GENERATOR ........................................................................................................................................14
USING THE GENERATOR...............................................................................................................................................15
AC Usage...............................................................................................................................................................15
Overload Indicator..................................................................................................................................................16
Economy Control Switch ........................................................................................................................................16
AC Parallel ............................................................................................................................................................1 7
STOPPING THE GENERATOR........................................................................................................................................18
MAINTENANCE/CARE .....................................................................................................................................................18
Recommended Maintenance Schedule .................................................................................................................18
Cleaning The Generator.........................................................................................................................................18
Checking The Oil Level ..........................................................................................................................................19
Changing/Adding Oil ..............................................................................................................................................19
Air Filter Maintenance ............................................................................................................................................20
Changing Fuel Line ................................................................................................................................................20
Spark Plug Maintenance ........................................................................................................................................20
Emptying The Fuel Tank ........................................................................................................................................20
STORAGE/TRANSPORT PROCEDURES .......................................................................................................................21
TROUBLESHOOTING ......................................................................................................................................................22
PARTS DIAGRAM ............................................................................................................................................................25
EMISSION CONTROL SYSTEM WARRANTY.................................................................................................................38

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
4
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
What You Need to Know About Safety Instructions
Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that
may occur. Common sense, caution and care must be exercised when operating or cleaning tools and equipment.
Always contact your dealer, distributor, service agent or manufacturer about problems or conditions you do not understand.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may
result in property damage.
2 YEAR LIMITED EMISSION-RELATED WARRANTY
THIS ENGINE MEETS U.S. EPA EMISSION STANDARDS UNDER 40 CFR 1054.625 .The emission-related limited warranty is valid for two (2)
years. Keep the purchase receipt and mail in the product registration card for proof of purchase. Buffalo Corp limits emission-related warranty repairs
to authorized service centers for owners located within 100 miles of an authorized service center. For owners located more than 100 miles from an
authorized service center, Buffalo Corp will, in its sole discretion, either pay for shipping costs to and from an authorized service center, provide for a
service technician to come to the owner to make the warranty repair, or pay for the repair to be made at a local non-authorized service center. The
provisions of this paragraph apply only for the contiguous states, excluding the states with high-altitude areas identified in 40 CFR part 1068,
Appendix III.
To exercise this warranty, DO NOT RETURN TO RETAILER. Instead, call Customer Service toll free at 1-866-460-9436 (email address
[e-mail]) and you will be instructed on where to take the engine for warranty service. Take the generator and proof of purchase (your
receipt) to the repair facility recommended by the Customer Service Representative. The warranty does not extend to generators damaged or
affected by fuel contamination, accidents, neglect, misuse, unauthorized alterations, use in an application for which the product was not designed
and any other modifications or abuse.
1 YEAR LIMITED WARRANTY (30 Day Limited Warranty for Commercial and Rental Purpose)
Generators are warranted to be free from defects in materials and workmanship for a period of 1 YEAR from date of original purchase. Buffalo Corp.
is not liable for any indirect, incidental or consequential damages from the sale or use of this product. Any implied warranties are limited to 1 YEAR
as stated, or as otherwise stated, in this written limited warranty. Some states do not allow the exclusion or limitation of incidental or consequential
damages. Some states do not allow limitation on the length of an implied warranty. Buffalo Corp will repair or replace, at its discretion, any part that
is proven to be defective in materials or workmanship under normal use during the 1 YEAR warranty period. Warranty repairs or replacements will be
made without charge for parts or labor. Parts replaced during warranty repairs will be considered as part of the original product and will have the
same warranty period as the original product. This warranty gives you specific legal rights, and you may have other rights that vary state to state.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
5
Notice Regarding Emissions:
Engines certified to comply with California and U.S. EPA emission regulations for SORE (Small Off Road Equipment) are certified to operate on
regular unleaded gasoline and may include the following emission control systems: Three-Way Catalyst (TWC) (if equipped), and Engine
Modifications (EM).
Legal Requirements:
Federal and/or State Occupational Safety and Health Administration (OSHA) regulations, local codes, and/or ordinances may apply to the intended
use of this generator. Consult a qualified electrician, electrical inspector, and/or the local agency having jurisdiction. Some areas require generators
to be registered with local utility companies. Additional regulations may apply if this generator will be used at a construction site.
IMPORTANT SAFETY INSTRUCTIONS
STOP!
Before using this generator and if you have any questions regarding the hazard and safety notices listed in this manual and/or on this
generator, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time.
WARNING: Do not connect this generator to a home or office electrical system. Connecting a generator to your electric utility
company’s power lines or to another power source could damage your generator and your appliances and could cause serious injury or
even death to you or a utility worker who may be working on nearby power lines. Plug your appliances directly into the generator, do not
plug the generator into any electric outlet in your home. Doing so could create a connection to the utility company power lines. You are
responsible for ensuring that your generator’s electricity does not feed back into the electric utility power lines.
WARNING: Do not use this generator to provide power for emergency medical equipment or life support devices.
Carbon Monoxide Gas: When in operation, the exhaust from this generator contains poisonous carbon monoxide gas. Carbon monoxide
gas is both odorless and colorless AND may be present even if you do not see or smell gas. Breathing this poison gas can lead to
headaches, dizziness, drowsiness, loss of consciousness and eventually death.
WARNING: USE THIS GENERATOR ONLY OUTDOORS IN NON-CONFINED AREAS. DO NOT SECURE THE GENERATOR WITH A CHAIN
OR ROPE, AS THIS WILL MAKE IT DIFFICULT TO MOVE IN AN EMERGENCY.
• Keep at least several feet of clearance on all sides to allow proper ventilation for this generator.
Usage: Avoid the use of extension cords if possible. If you choose to use them, be sure they are sized adequately to handle the flow of
electricity. An undersized cord can overheat, short out and cause a fire.
Powerful Voltage: This generator produces powerful voltage, which can result in electrocution.
• ALWAYS ground this generator before using it. (See “Ground the Generator” section in this manual).
• Only electrical devices should be plugged into this generator, either directly or with an extension cord. NEVER connect a building electrical
system to this generator without a qualified electrician. Doing so voids your warranty.Such connections must isolate generator power from utility
power and comply with local electrical laws and codes. Failure to comply can create a back feed into utility lines creating an electrocution hazard,
which may result in serious injury or death to utility workers. Such a back feed may cause this generator to explode, burn and create fires when
utility power is restored.
• Use a ground fault circuit interrupter (GFCI) in highly conductive areas such as metal decking or steel work. GFCIs are available in-line with some
extension cords.
• Keep generator dry and operate with dry hands. Do not use this generator in wet conditions (rain, snow, active sprinkler system, wet hands, etc.).
• Do not touch bare wires or outlets (receptacles).
• Do not allow children or non-qualified persons to operate this generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
6
Flammable Gasoline: This generator may emit highly flammable and explosive gasoline vapors, which can cause severe burns or even
death. A nearby open flame can lead to an explosion even if not directly in contact with gasoline.
• Do not operate this generator near open flame.
• Do not smoke near this generator.
• Always operate this generator on a firm, level surface.
Gasoline is highly flammable and explosive. Handling fuel can result in serious injury or burns.
• Always shut down this generator before refueling. Refuel in a well-ventilated area. Keep heat, sparks and flame away while refueling and away
from the location where gasoline is stored. Never refuel indoors where gasoline fumes may reach flames and/or sparks.
• Allow this generator to cool for at least 2 minutes before removing the fuel tank cap. Loosen the cap slowly to relieve pressure in the fuel tank.
Avoid spilling fuel.
• Do not fill the fuel tank above the upper limit line. Gasoline may expand during operation. Do not fill to the top of the tank.
• Always check for spilled gasoline and immediately wipe it up before starting this generator.
• Empty the fuel tank before storing or transporting this generator.
• Always handle fuel outdoors.
• Before transporting, turn the fuel valve to the “OFF” position and disconnect the spark plug.
High Temperatures: This generator produces heat when in operation. Temperatures near the exhaust can exceed 150 Degrees
Fahrenheit (65 Degrees Celsius).
• Do not touch hot surfaces. Observe all warning placards on this generator denoting hot surfaces.
• Allow this generator to cool for several minutes after use before touching the engine, muffler or other areas that are hot during operation and
before storing indoors.
• Hot exhaust may ignite some materials. Keep flammable materials away from this generator.
• Keep at least several feet of clearance on all sides of this generator during operation. Do not enclose this generator in any structure.
Usage: Consult a physician(s) before using this generator if using a pacemaker. Electromagnetic fields in close proximity to a heart
pacemaker could cause a pacemaker to malfunction or fail. Caution is necessary when near the engine’s recoil starter.
Usage: Prolonged exposure to high noise levels can be hazardous to hearing. Always wear ANSI-approved hearing protection when
operating or working around the generator when it is running.
Usage: Misuse of this generator can damage it or shorten its life. Use this generator only for its intended purpose.
• Operate this generator only on a dry, level surface. Do not secure the generator with a chain or rope, which would prevent it from being moved in
an emergency.
• Allow this generator to run for several minutes before connecting any electrical devices.
• Promptly turn off any malfunctioning devices and disconnect them.
• Do not operate an excessive number of electrical devices in excess of the wattage capacity of this generator.
• Do not turn on electrical devices until after they are connected to this generator.
• Turn off all connected electrical devices before stopping this generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
7

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
8
In addition to the previously described safety information, familiarize yourself with all safety and hazard placards on this generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
9
PACKAGE CONTENTS
The following item is supplied with this Generator. Verify that it is included.
STOP!
If there are missing items, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time for customer service.
Item List:
Spark plug wrench

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
10
GENERATOR COMPONENTS
Observe the locations and functions of the various components and controls of this generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
11
PREPARING THE GENERATOR FOR USE
Using this Generator for the First-Time
STOP!
The following section describes the required steps for preparing this generator for the first use. Failure to correctly perform these steps
can damage this generator and/or shorten its life. If still unsure about how to perform any of these steps after reading this section, call
1-866-460-9436 Monday - Friday, 8 AM - 4 PM Central Time for customer service.
If this generator is being used for the first time, the following few steps are required to prepare it for operation:
Step 1 - Add Oil
THIS GENERATOR REQUIRES AT LEAST 20.2 OUNCES OF OIL (SAE10W-30) TO RUN.
ADD OIL UNTIL IT IS ALMOST OVERFLOWING. THE LOW-OIL SENSOR IS VERY SENSITIVE AND THE ENGINE
WILL NOT RUN IF THE OIL IS LOW. START WITH 20.2 OUNCES, THEN ADD MORE UNTIL ALMOST OVERFLOWING.
TROUBLESHOOTING: IF THE GENERATOR WILL NOT START, DOUBLE CHECK THAT THE OIL LEVEL IS
COMPLETELY FULL AND ALMOST OVERFLOWING.
This generator requires engine oil to function. Engine oil is a major factor affecting engine performance and service life. When new from
the package, this generator contains no oil in the engine crankcase. Add oil before operating this generator for the first time. When replenishing oil
for subsequent use of this generator, always determine that this generator has the correct quantity of oil.
To add oil to the engine crankcase:
1. Confirm that this generator is on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine as illustrated in Figure 1 below.
3. Using a funnel, add high detergent motor oil to fill the engine crankcase to the correct quantity. SAE10W-30 oil is recommended for general use.
When the engine crankcase is full and almost overflowing, the oil level should reach the lower lip of the oil filling opening as shown in Figure 2.
4. Replace the oil filler/dipstick cap and close the oil access panel.
Figure 1 – Unscrew the Dipstick Cap
Figure 2 - Add Oil

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
12
Step 2 - Add Gasoline
Gasoline and gasoline fumes are highly flammable and explosive. Handling fuel can result in serious injury or burns.
• Do not fill the fuel tank near a heat, sparks or an open flame. Keep gasoline away from appliance pilot lights, barbecues, electric appliances, power
tools, etc.
• Do not overfill the fuel tank. Always check for fuel spills and immediately wipe them up. Spilled fuel is a fire hazard and causes environmental
damage.
To add gasoline:
To ensure that this generator runs smoothly, use only FRESH, UNLEADED GASOLINE WITH AN OCTANE RATING OF 87 OR HIGHER. Unleaded
gasoline produces fewer engine and spark plug deposits and extends the life of the exhaust system.
1. Confirm that this generator is on a level surface.
2. Unscrew fuel tank cap and set aside. (NOTE: The fuel tank cap may be tight and difficult to unscrew.)
3. Slowly add fresh, unleaded gasoline (with an octane rating 87 or higher) to the fuel tank. Be careful not to fill the fuel tank above the upper limit
line. NOTE: Because gasoline can expand, do not fill the fuel tank to the very top.
4. Securely tighten the fuel tank cap and immediately wipe up any spilled gasoline with a dry cloth.
Fuel Tank Capacity (gallons)
3.1
Fuel Type
Fresh, Unleaded Gasoline Octane Rating 87 or Higher
IMPORTANT:
• Use only UNLEADED gasoline with an octane rating of 87 or higher.
• Never use a mixture of oil and gasoline.
• Never use old and/or contaminated gasoline.
• Avoid getting dirt and/or water in the fuel tank.
• Gasoline can age in the fuel tank and make it difficult to start this generator. Never store this generator for extended time with gasoline in the
fuel tank.
Step 3 - Ground the Generator
Failure to properly ground this generator can result in electrocution.
Ground this generator by tightening the grounding nut against a grounding wire as illustrated in Figure 3. A No. 12 AWG (American Wire Gauge)
stranded copper wire is generally an acceptable grounding wire. The other end of this grounding wire should be connected to a copper or brass
grounding rod that is driven into the earth.
Grounding codes can vary by location. Contact a local electrician for information on grounding regulations for your area.
Figure 3
The Grounding Terminal
is located on the front of
the generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
13
Subsequent Use of this Generator
For subsequent uses of this generator after the first use, certain steps still must be completed to prepare it for operation.
IMPORTANT: Be familiar with the procedures described in the previous section titled “Using the Generator for the First Time” of this
manual. If not, review this section now.
Step 1 - Verify Oil Level
It is important to check the oil level in the engine crankcase before each use to ensure that there is sufficient quantity.
1. Verify that this generator is on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine.
3. With a dry cloth, wipe the oil off of the dipstick that is located on the inside of the cap.
4. Fully insert the dipstick without screwing the filler/dipstick cap and then remove again. There should be oil on the dipstick. If there is no oil on the
dipstick, or oil is visible only at the very end of the dipstick, add oil until the engine crankcase is filled. (See “Changing/Adding Oil” in the
“Maintenance/Care” section of this manual).
5. Confirm that the oil filler/dipstick cap is properly screwed in place when finished verifying the oil level.
Step 2 - Verify Gas Level
Before starting this generator, verify that there is sufficient gasoline in the fuel tank. If necessary, add fresh unleaded gasoline with an octane rating
of 87 or higher according to “Step 2 - Add Gasoline” of the “Using this Generator for the First Time” section of this manual.
Fuel Tank Capacity (gallons)
3.1
Fuel Type
Fresh, Unleaded Gasoline Octane Rating 87 or Higher
Gasoline and gasoline fumes are highly flammable and explosive. Handling fuel can result in serious injury or burns.
• Do not fill the fuel tank near a heat, sparks or an open flame. Keep gasoline away from appliance pilot lights, barbecues, electric appliances, power
tools, etc.
• Always allow several minutes for the engine to cool before refueling.
• Do not overfill the fuel tank. Always check for fuel spills and immediately wipe them up. Spilled fuel is a fire hazard and causes environmental
damage.
IMPORTANT:
• Use only fresh UNLEADED gasoline with an octane rating of 87 or higher.
• Never use old and/or contaminated gasoline.
• Never use a mixture of oil and gasoline.
• Avoid getting dirt and/or water in the fuel tank.
• Never store generator for extended time with gasoline in the fuel tank.
Step 3 - Ground the Generator
Failure to properly ground this generator can result in electrocution.
Ground this generator by tightening the grounding nut against a grounding wire as previously illustrated in Figure 3. A generally acceptable
grounding wire is a No. 12 AWG (American Wire Gauge) stranded copper wire. The other end of this grounding wire should be connected to a
copper or brass grounding rod that is driven into the earth.
Grounding codes can vary by location. Contact a local electrician for information on grounding regulations for your area.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
14
STARTING THE GENERATOR
STOP!
Before starting this generator, confirm that all the steps in the section titled, “Preparing the Generator for Use,” of this manual have been
correctly completed. If unsure about how to perform any of these steps, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time for
customer service.
Disconnect all electrical loads from this generator before attempting to start.
To start this generator:
1. Confirm that there are no electrical devices connected to this generator. Connected devices may increase the difficulty in starting the engine.
2. Confirm that this generator is properly grounded. (See “Ground the Generator” section of this manual.)
3. Turn the fuel petcock to the “on” position.
4. Move the choke lever to the “Closed/Choke” position.
5. Set the engine switch to the “on” position.
6. Slowly pull on the recoil starter handle, shown in Figure 4, until a slight resistance is felt. Then pull briskly to start the engine. Gently return the
cord into the generator to avoid damage to the starter or housing. Never allow the cord to snap back.
7. If the engine fails to start, repeat step 6. NOTE: After repeated attempts to start the engine, consult the troubleshooting guide before attempting
again. If problems persist, call 1-866-460-9436, Monday - Friday, 8 AM - 4 PM Central Time.
8. Once the engine has started, GRADUALLY move the choke lever to the “Open To Run” position until the engine levels off.
Then let the engine run approximately 5 minutes BEFORE adding appliances or tools.
Fuel Cock
The fuel cock is located between the fuel tank and carburetor. When the fuel cock is in the ON position, fuel is allowed to flow from the fuel tank to
the carburetor. Be sure to return the fuel cock to the OFF position after stopping the engine.
Choke Rod
The choke is used to provide an enriched fuel mixture when starting a cold engine. It can be opened and closed by operating the choke rod
manually. Pull the rod out toward CLOSED to enrich the mixture for cold starting
Figure 4
The Recoil Start is located on the left
side of the generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
15
USING THE GENERATOR
• USE THIS GENERATOR ONLY OUTDOORS IN NON-CONFINED AREAS. DO NOT SECURE THE GENERATOR WITH A CHAIN OR ROPE, AS
THIS WILL MAKE IT DIFFICULT TO MOVE IN AN EMERGENCY.
• Keep at least several feet of clearance on all sides to allow proper ventilation for this generator.
After the engine has been running for several minutes, electrical devices may be connected to this generator.
AC Usage
Electrical devices running on AC current may be connected according to their wattage requirements.
Rated (Running) Wattage
2850
Surge Wattage
3000
The rated (running) wattage corresponds to the maximum wattage a generator can output on a continuous basis.
The surge wattage corresponds to the maximum amount of power a generator can output for a short time. Many electrical devices, such as a
refrigerator, require short bursts of extra power for starting and stopping fan motors, etc., in addition to their listed rated wattage. Motorized devices
typically require more than their rated wattage for startup. The surge wattage ability of a generator allows for this extra power requirement.
The total running wattage requirement of the electrical devices connected to a generator should not exceed the rated wattage of the generator itself.
To calculate the total wattage requirement of the electrical devices to be connected, look up the rated (running) wattage of each device and add
these numbers together to find the total wattage that all of the devices together will draw from the generator. If the total wattage of the selected
devices exceeds the rated wattage of the generator, DO NOT connect all of the devices. Select a combination of the electrical devices that will have
a total wattage less than or equal to the rated wattage for the generator.
This generator can run at its surge wattage capacity for only a short time. Connect electrical devices requiring a rated (running) wattage
equal to or less than the rated wattage of this generator. Never connect devices requiring a rated wattage equal to the surge wattage of a
generator.
A device's rated (running) wattage should be listed somewhere on the device itself and/or in its manual. If the wattage specification for a device is not
available, the wattage can be calculated by multiplying the Voltage requirement (120) by the Amperage drawn.
Watts = Volts x Amperes
Or, the wattage required by a device can be estimated by using the following chart. The chart provides only estimates and it is better to know the
exact wattage of each electrical device to be powered by this generator.
NOTE: Plug appliances into the correct outlet. Connect
standard 120 Volt, single phase, 60 Hz loads to the 120
Volt outlet. Connect 12 Volt, DC loads to the 12 Volt
outlet.
Electrical Device
Rated (Running) Watts
Additional Surge Watts
air compressor (1 - 1/2 HP)
2500
2500
airless sprayer (1/3 HP)
600
1200
coffee maker
1500
0
computer w/17 inch monitor
800
0
deep freezer
500
500
electric drill (1/2 HP)
1000
1000
furnace fan blower (1/2 HP)
800
1300
hot plate
2500
0
microwave oven (1000 watt)
1000
0
quartz halogen work light
1000
0
refrigerator/freezer (18 Cu. Ft.)
800
1600
saw - circular (7 1/4 inch)
1500
1500
stereo receiver
450
0
electric stove - single element
1500
0
sump pump
800
1200
television (27 inch color)
500
0
well water pump (1/3 HP)
1000
2000
window air conditioner (10000 BTU)
1200
1800
window fan
300
600
Connect only electrical devices that are in good
working order. Faulty devices or power cords
present the risk of electrical shock. Immediately
turn off and disconnect any device that
commences to operate abnormally, sluggish or
abruptly stops. Determine if the problem was the
device or the rated load capacity of this generator
has been exceeded.
Figure 5 - Estimated wattage requirements for
common electrical devices

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
16
Even though Generator has an overall rated wattage of 2850, do not attempt to draw more than 20 AMPS from any set of two receptacles
of the 120 Volt outlets. Draws higher than 20 Amps will damage this generator and void the warranty.
Turn on the connected electrical devices beginning with the device with the highest rated wattage requirement and then each additional device with
the next lower rated wattage requirement.
Do not connect 50Hz or 3-phase loads to this generator.
Do not secure the generator with a chain or rope, which would prevent it from being moved in an emergency.
To Plug Items Into the Generator
1. Allow the engine to run for several minutes after it has been started.
2. Confirm that the electrical device is switched off prior to plugging it into this generator.
4. Turn on the connected electrical devices beginning with the device with the highest rated wattage requirement and then each additional device
with the next lower rated wattage requirement.
SOME NOTES ABOUT POWER CORDS
Long or thin cords can require more wattage from a generator to power an electrical device. Figure 6 shows the recommended cords according to
the power requirement of the electrical device. When using cords that exceed these specifications, allow for the electrical device to have a slightly
higher rated wattage requirement.
Device Requirements
Max. Cord Length (ft) by Wire Gauge
Amps
Watts (120V)
Watts (240V)
#8 wire
#10 wire
#12 wire
#14 wire
#16 wire
2.5
300
600
NR
1000
600
375
250
5
600
1200
NR
500
300
200
125
7.5
900
1800
NR
350
200
125
100
10
1200
2400
NR
250
150
100
50
15
1800
3600
NR
150
100
65
NR
20
2400
4800
175
125
75
50
NR
25
3000
6000
150
100
60
NR
NR
30
3600
7200
125
65
NR
NR
NR
40
4800
9600
90
NR
NR
NR
NR
Figure 6 - Maximum Extension Cord Lengths by Power Requirement
OVERLOAD INDICATOR LIGHT
The overload indicator light flickers when an overload of a connected electrical device is detected. This situation shall not be kept for a long time and
it just needs to decrease the loads to its normal range and the overload indicator light will go off.
When the load is detected to exceed the maximum power or the AC output voltage is reduced, the overload indicator light will come on and the
electronic breaker will then activate, stopping power to the generation in order to protect the generator and any connected electric devices. The
output pilot light (Green) will be off, the overload indicator light will turn RED.
(a) Turn off any connected electric devices
(b) Reduce the total wattage of connected electric.
(c) Check for blockages in the cooling air inlet, muffler air exhaust pipe opening and the control unit.
(d) After inspection, press the reset button to restore the power supply of the generator.
NOTE: The generator AC output automatically resets when the engine is stopped and then restarted.
NOTE: The overload indicator light may come on for a few seconds at first when using electric devices that require a large starting current, such as
a compressor or a submergible pump. However, this is not a malfunction.
ECONOMY CONTROL SWITCH
When the economy control switch is turned ON, the economy control unit control the engine speed according to the connected load. The results are
better fuel connection and less noise.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
17
Turning Off Generators while in Parallel Function
1. Disconnect or turn off item plugged into parallel receptacle.
2. Turn off both generators.
3. Carefully disconnect the parallel cables from both generators
AC PARALLEL TERMINALS
The parallel port terminals are used with a parallel kit (sold separately). It will allow two generators to be linked to
increase output. The black and white wire connections are non-polarized and can be inserted into either the left or
right ports.
NOTE: Do not disconnect cables while the generator is running. The generator or the load may be damaged.
NOTE: Only connect two identical Inverter Generators together using a Parallel Kit.
Before connecting an appliance to a generator, make sure that the appliance is in good working order and that its
electrical rating does not exceed that of the outlet. Most appliances require more than their electrical rating for
startup.
1. Have both generators ready to operate.
2. Plug in BOTH parallel cables FIRST. If you attach black wire on left A and white wire on right B, duplicate the
same position on the opposite generator.
3. Attach both ground connections on both control panels.
4. Power up each generator, with the Economy Switch in off position.
5. After running a few minutes, plug in appliances into RV cable or outlet on control panel. Make sure appliances are
off.
6. Gradually turn on each appliance after making sure both generators are in normal running (the output indicator
LED (green)
flashes.
Note: The required power of the electrical appliance connected to the parallel outlet cannot exceed the rated output
of paralleled generators. See specifications page in owner’s manual.
Do not pair more than 2 generators.
Only use the BUFFALO parallel output cable for parallel operation (sold separately).
You can use the outlets on the control panel of the generator while operating in parallel. Do not exceed combined
load on all outlets 26 amps running or 33 amps surge.
If parallel cables are not properly connected to the generators, either or both generators can be damaged and
could explode.
DO NOT connect or disconnect the parallel connection cable from the control panel while the generators are
running. Turn off both generators before disconnecting parallel cables.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
18
STOPPING THE GENERATOR
To stop this generator:
1. Turn off all connected electrical devices and then unplug them.
2. Allow this generator to run for several more minutes with no electrical devices connected to help stabilize the temperature of this generator.
3. Set the engine power switch to the “OFF” position.
Allow this generator to cool down before touching areas that become hot during operation.
Allowing gasoline to sit in this generator's fuel tank for extended time without use can increase the difficulty in starting this generator in
the future. Never store this generator for extended time with gasoline in the fuel tank.
MAINTENANCE/CARE
Proper routine maintenance of this generator is essential for safe, economical, and trouble-free operation. It will help prolong the life of this generator
as well as help reduce air pollution. Perform maintenance checks and procedures according to the schedule in Figure 7.
Never perform maintenance procedures while this generator is running. Allow this generator to cool before commencing any maintenance
procedures. Keep heat, sparks and flame away.
Improper maintenance and/or failure to correct any problems prior to operating this generator can cause a malfunction which could cause
death or serious injury. Always follow the inspection and maintenance recommendations and schedules in this manual.
Recommended Maintenance Schedule
Each Use
Every Month or
Each 20 Hrs
Every 3 Months or
Each 50 Hrs
Every 6 Months or
Each 100 Hrs
Every Year or
Each 300 Hrs
Engine Oil
Check Level
X
Replace
X (first use)
X
Air Filter
Check
X
Clean
X
Spark Plug
Check/Clean
X
Fuel Tank
Verify Gas Level
X
Clean
X
Figure 7 - Recommended maintenance schedule
Cleaning the Generator
Always try to use this generator in a cool dry place. If this generator becomes dirty, the exterior can be cleaned with a damp cloth, soft brush,
vacuum and/or pressurized air.
Never clean this generator with a bucket of water and/or a hose as water can get inside and cause a short circuit or corrosion.
Never use gasoline to clean parts of this generator.

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
19
Checking the Oil Level
It is important to check the oil level in the engine crankcase before each use to ensure that there is a sufficient quantity.
To check the oil level:
1. Verify that this generator is shut down and on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine.
3. With a dry cloth, wipe the oil off of the dipstick that is located on the inside of the cap.
4. Insert the dipstick as if replacing the cap and then remove again. There should be oil on the dipstick. If there is no oil on the dipstick, or oil is
visible only at the very end of the dipstick, add oil until the engine crankcase is filled.
5. Confirm that the oil filler/dipstick cap is properly in place when finished verifying the oil level.
Changing/Adding Oil
The oil level in this generator should be checked before each use. When the oil level is low, add oil until the level is sufficient to operate this
generator. (See Figure 8B)
The oil should be changed after the first 20 hours of operation. Subsequently, the oil should be changed every 6 months, or for every 100 hours of
use, or when the oil has become contaminated with water and/or dirt.
To drain the oil from this generator:
1. Place a bucket underneath this generator to catch oil as it drains.
2. Unscrew the oil drain plug located on the crankcase underneath the oil filler/dipstick cap using 10 mm hex wrench. Figure 8A
3. Allow all the oil to drain from this generator.
4. Replace the oil drain plug and tighten using 10 mm hex wrench.
NOTE: Never dispose of used motor oil in the trash, down a drain or on the ground. Put oil in a sealed container and contact your local
recycling center or auto garage to arrange oil disposal.
THIS GENERATOR REQUIRES AT LEAST 20.2 OUNCES OF OIL (SAE10W-30) TO RUN.
ADD OIL UNTIL IT IS ALMOST OVERFLOWING. THE LOW-OIL SENSOR IS VERY SENSITIVE AND THE ENGINE
WILL NOT RUN IF THE OIL IS LOW. START WITH 20.2 OUNCES, THEN ADD MORE UNTIL ALMOST OVERFLOWING.
TROUBLESHOOTING: IF THE GENERATOR WILL NOT START, DOUBLE CHECK THAT THE OIL LEVEL IS
COMPLETELY FULL AND ALMOST OVERFLOWING.
Figure 8B – Adding oil
Figure 8A –
REMOVE bolt
and drain oil

ITEM # GEN3000IOF Portable Gas Fuel Inverter Generator
20
Air Filter Maintenance
Routine maintenance of the air filter helps maintain proper airflow to the carburetor. Occasionally verify that the air filter is free of excessive dirt. The
air filter will require more frequent cleaning when operating this generator in extremely dusty areas.
To clean the air filter, remove the foam filter element from the generator and wash it in warm water and household dish detergent. Thoroughly rinse
and dry. Pour a small amount of motor oil onto the filter, ring out ALL excess oil, and reinstall the foam filter element in the generator.
Unscrew the bolts, or unsnap the clips at the top and bottom of the air filter cover, located below the choke lever, to access the foam filter element.
Spark Plug Maintenance
The spark plug is essential for proper engine operation. The spark plug should be intact, free of deposits, and properly gapped. A bad or incorrectly
installed spark plug can cause engine damage. To inspect the spark plug:
1. Remove the spark plug by pulling on the spark plug cap.
2. Unscrew the spark plug from this generator by using the included spark plug wrench.
3. Visually inspect the spark plug. If it is cracked and/or chipped, discard and install a new spark plug. A F7RTC Torch spark plug, such as
NGK BPR7ES is recommended.
4. Measure the spark plug electrode gap with a gauge. The gap should be 0.020-0.028in (0.5-0.7mm). (See Figure 9.)
5. If re-using the spark plug, use a wire brush to clean any dirt from around the spark plug base and then re-gap the spark plug.
6. Screw the spark plug back into place on this generator by using the included spark plug wrench.
7. Replace the spark plug cap.
Figure 9
Measuring the spark plug gap
To store this generator for extended time, drain the gasoline from the carburetor AND fuel tank.
To drain gasoline from this generator:
1. Turn the fuel valve to the “off” position and let the engine run until it stops.
2. Remove the fuel filter cup.
3. Empty the fuel filter cup of any fuel.
4. Place a receptacle underneath this generator to catch gasoline as it drains.
5. Turn the fuel valve to the “on” position and allow all gasoline to drain.
6. Turn the fuel valve to the “off” position.
7. Replace the fuel filter cup.
8. Store the drained gasoline in a suitable place.
To store this generator for extended time, the fuel needs to be drained from the carburetor. To drain the gasoline from the carburetor turn the fuel
valve to the “off” position while the engine is running. The generator will shut down when all the gasoline in the carburetor has been used.