SportsPlay Equipment MUSTANG EASY RIDER 361-501 User manual

361-501 EASY RIDER (MUSTANG)
361-502 EASY RIDER (PONY)
361-503 EASY RIDER (ZEBRA)
361-504 EASY RIDER (BRONCO)
Page 1
Rev 01/25/11
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
* IMPORTANT *
PLEASE RETAIN THIS INSTRUCTION SHEET IN YOUR FILES. IT CONTAINS IMPORTANT REPLACEMENT
PARTS INFORMATION. ALL EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THESE
INSTRUCTIONS.
IT IS IMPORTANT TO USE AND MAINTAIN ALL PUBLIC PLAYGROUND EQUIPMENT PROPERLY. PLAYGROUND
EQUIPMENT WHICH IS IMPROPERLY MAINTAINED CAN CAUSE SERIOUS INJURY. PERIODICAL
INSPECTIONS, MAINTENANCE, REPAIR AND/OR REPLACEMENT OF DAMAGED PARTS IS NECESSARY FOR
SAFE OPERATION OF EQUIPMENT AND SAFETY OF USERS. RESILIENT SURFACING SHOULD BE USED
UNDER ALL PLAYGROUND EQUIPMENT. APPROPRIATE PUBLICATIONS, AVAILABLE AT NO CHARGE, FROM
THE CONSUMER PRODUCT SAFETY COMMISSION, INCLUDE “A HANDBOOK FOR PUBLIC PLAYGROUND
SAFETY.” YOU CAN RECEIVE YOUR FREE COPY BY CALLING 1-301-504-7908
PACKING LIST for 361-501
1
CTN
-
1
Hardware
Bag
-
1
363-001
Mustang
1
CTN
-
1
363-950
Spring Assy.
PACKING LIST for 361-502
1
CTN
-
1
Hardware
Bag
-
1
363-002
Pony
Note: Hardware Bag is the same for all Packing
Lists.
1
CTN
-
1
363-950
Spring Assy.
HARDWARE BAG
4
-
116-506
5/16” x 1 ½” Hex Hd Bolt
PACKING LIST for 361-503
4
-
196-644
3/8” x 8” Anchor Bolt
1
CTN
-
1
Hardware
Bag
8
-
316-501
5/16” Flat Washer
-
1
363-003
Zebra
4
-
226-501
5/16” Lock Nut
1
CTN
-
1
363-950
Spring Assy.
4
-
226-601
3/8” Lock Nut
4
-
216-601
3/8” Hex Nut
PACKING LIST for 361-504
4
-
316-601
3/8” Flat Washer
1
CTN
-
1
Hardware
Bag
1
-
805-532
Warning Label
-
1
363-004
Bronco
1
-
805-534
SportsPlay Label
1
CTN
-
1
363-950
Spring Assy.
1
-
Maintenance Checklist
2CTN 1 PC 2 TOTAL PCS WT 56# CLASS 70

361-501 EASY RIDER (MUSTANG)
361-502 EASY RIDER (PONY)
361-503 EASY RIDER (ZEBRA)
361-504 EASY RIDER (BRONCO)
Page 2
Rev 01/25/11
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS
STATIONARY & PORTABLE EQUIPMENT –USE/FALL ZONES SHOULD EXTEND A MINIMUM OF 6 FEET IN ALL
DIRECTIONS FROM THE PERIMETER OF THE EQUIPMENT GROUND SPACE. THIS AREA SHOULD BE COVERED
WITH THE REQUIRED AMOUNT OF RESILIENT SAFETY SURFACING MATERIAL. FOR SOME EQUIPMENT –
USE/FALL ZONES CAN OVERLAP. SEE CONSUMER PRODUCT SAFETY COMMISSION GUIDELINES.
DIAMETER & DEPTH OF FOOTINGS ILLUSTRATED ARE SATISFACTORY IN MOST APPLICATIONS FOR PIPE
SIZES UP TO 2 3/8” DIAMETER. VARYING SOIL & CLIMATIC CONDITIONS MAY REQUIRE DEEPER &
HEAVIER FOOTINGS IN SOME AREAS. CHECK LOCAL BUILDING CODES.
* If resilient surfacing is to be less than 12”, then additional pipe should be put in
concrete to maintain proper finish grade for equipment.

361-501 EASY RIDER (MUSTANG)
361-502 EASY RIDER (PONY)
361-503 EASY RIDER (ZEBRA)
361-504 EASY RIDER (BRONCO)
Page 3
Rev 01/25/11
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]

361-501 EASY RIDER (MUSTANG)
361-502 EASY RIDER (PONY)
361-503 EASY RIDER (ZEBRA)
361-504 EASY RIDER (BRONCO)
Page 4
Rev 01/25/11
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
GENERAL ASSEMBLY INSTRUCTIONS:
Check all the parts and hardware with the packing list to be sure you have received
everything needed to assemble this product. CONTACT YOUR LOCAL DISTRIBUTOR WITH
NOTIFICATION OF ANY MISSING OR DAMAGED PARTS. Contact must be made within ten days of
receipt of your order.
Only hand-tighten nuts & bolts on initial assembly. Final tightening should be done
EVENLY after final assembly when unit has been plumbed & leveled.
After assembly is complete, ANY ENDS OF BOLTS PROTRUDING BEYOND NUTS SHOULD BE CUT OFF
AND/OR PEENED OVER TO REMOVE ANY SHARP EDGES. Go over entire unit to file smooth any
sharp edges or projections that may have been caused by rough handling in shipping or
installation. T-Clamps are designed for both one and two bolt connections. In many
situations only one bolt is required. See specific assembly instructions.
On products with platforms install 1 – 2 degrees off level to facilitate water drainage.
SPECIFIC ASSEMBLY INSTRUCTIONS:
STEP #1:
Dig footing hole & fill with concrete. (Approx. 3.5 cubic feet.)
STEP #2:
Before concrete sets, assemble anchor bolts to bottom plate of spring with a
Hex Nut & Lock Nut.
STEP #3:
Push this assembly down into the wet concrete until plate is level with top
of concrete.
STEP #4:
After concrete hardens for at least 48 hours, bolt pony in place. Add
resilient surfacing.
STEP #5:
IMPORTANT: After equipment has been in use for three or four days, all
bolts & nuts must be checked and retightened if necessary.
STEP #6:
Attach Warning Label and Manufacturer’s Identification Label to a clean
surface. The Labels should be attached in a location where they are clearly
visible and legible and away from normal hand and foot placement areas. The
Labels must be replaced if they become illegible, destroyed or removed.
Contact your distributor for replacement Labels.
GENERAL MAINTENANCE INSTRUCTIONS:
Check WEEKLY/DAILY (DEPENDING ON USE) for loose bolts, damaged or broken parts. Tighten
and/or replace immediately. Inspect unit for sharp edges or damaged finish and smooth or
repair with touchup paint. Contact your distributor for replacement parts
KEEP A COPY OF THESE INSTRUCTIONS ON FILE FOR MAINTENANCE
PURPOSES

361-501 EASY RIDER (MUSTANG)
361-502 EASY RIDER (PONY)
361-503 EASY RIDER (ZEBRA)
361-504 EASY RIDER (BRONCO)
Page 5
Rev 01/25/11
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
USE ZONE