SportsPlay Equipment RABBIT HUTCH User manual

301-141 RABBIT HUTCH (Perm.)
Page 1
REV 11/17/09
301-141.I.CC.1109.2
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
IMPORTANT
Please retain this instruction sheet in your files. It contains important
replacement parts information. All equipment should be installed in accordance
with these instructions. It is important to use and maintain all public playground
equipment properly. Playground equipment, which is improperly maintained, can
cause serious injury. Periodical inspections, maintenance, repair and/or
replacement of damaged parts is necessary for safe operation of equipment and
safety of users. Resilient surfacing should be used under all playground
equipment. Appropriate publications, available at no charge, from the Consumer
Product Safety Commission, include “A Handbook for Public Playground Safety”. You
can receive your copy by calling 1-301-504-0708.
PACKING LIST
HARDWARE BAG
1
CTN
1
Hardware
Bag
4
116-608
3/8” x 2” Hex Head Bolt
1
CTN
1
113-306
2 –Ring Ladder
4
116-535
5/16” x 1 ½” Button Hd Bolt
1
SKID
1
113-044
Shell
4
216-512
5/16” Button Hd Nut
1
BDL
4
113-601
Legs
4
326-501
5/16” Lock Washer
2
416-350
3/16” Socket Key
4
326-601
3/8” Lock Washer
1
805-532
Warning Label
1
805-534
SportsPlay Label
1
Maintenance Checklist
2 CTN 1 BDL 1 SKID 4 TOTAL PCS WT 210# CLASS 70

301-141 RABBIT HUTCH (Perm.)
Page 2
REV 11/17/09
301-141.I.CC.1109.2
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS
Stationary & Portable equipment –Use/Fall Zones should extend a minimum of 6 feet in all
directions from the perimeter of the equipment ground space. This area should be covered
with the required amount of resilient safety surfacing material. For some equipment –
Use/Fall Zones can overlap. See Consumer Product Safety Commission Guidelines.
Diameter & Depth of footings illustrated are satisfactory in most applications for pipe
sizes up to 2 3/8” diameter. Varying soil & climatic conditions may require deeper &
heavier footings in some areas. Check local building codes.
•If resilient surfacing is to be less than 12”, then additional pipe should be put in concrete
to maintain proper finish grade for equipment.

301-141 RABBIT HUTCH (Perm.)
Page 3
REV 11/17/09
301-141.I.CC.1109.2
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL ASSEMBLY INSTRUCTIONS:
Check all the parts and hardware with the packing list to be sure you have received
everything needed to assemble this product. CONTACT YOUR LOCAL DISTRIBUTOR WITH
NOTIFICATION OF ANY MISSING OR DAMAGED PARTS. Contact must be made within ten days of
receipt of your order.
Only hand-tighten nuts & bolts on initial assembly. Final tightening should be done
EVENLY after final assembly when unit has bee plumbed and leveled.
GENERAL MAINTENANCE INSTRUCTIONS:
Check MONTHLY for loose bolts, damaged or broken parts. Tighten and/or replace
immediately.
SPECIFIC ASSEMBLY INSTRUCTIONS:
NOTE:
All threaded ends of bolts protruding beyond nuts must be cut off and/or peened
to eliminate sharp edges. No more than two threads should extend beyond face
of nut. All washers, “T” nuts, and other fastener hardware used on round pipe
or tubing must be hammered down to conform to the curved underlying surface to
eliminate catch points.
STEP #1:
Place 113-306, 2-Ring Ladder onto ground with ring that has (4) holes in it
facing upwards.
STEP #2:
Place 113-044 shell on top of 2-Ring Ladder so that the ladder will be beneath
the shell.
STEP #3:
Attach 2-Ring Ladder to Shell using 5/16” x 1-1/2” Button Head Bolts, 5/16”
Lock Washers, and 5/16” Button Head Nuts. Tighten Button Head Bolts and Nuts
with 3/16” Socket Key. See Detail A at the bottom of this page.
STEP #4:
Turn shell upside down and attach 113-610 Shell legs to Shell using 3.8” x 2”
Hex Head Bolts with 3/8” Lock Washers. See Detail B at the bottom of this
page.
STEP #5:
Check and tighten all Bolts and Nuts.
STEP #6:
Turn shell over onto its legs and position, mark and dig holes. See footing
drawing on page 2.
STEP #7:
Use suggested bracing method on page 2 for holding completed assembly in
position while pouring concrete into footing holes.
STEP #8:
Allow at least 48 hours for concrete to harden before using equipment.
STEP #9:
Attach Warning Label and Manufacturer’s Identification Label to a clean
surface. The Labels should be attached in a location where they are clearly
visible and legible and away from normal hand and foot placement areas. The
Labels must be replaced if the become illegible, destroyed or removed. Contact
your Distributor for replacement Labels.