SportsPlay Equipment Junior 311-145 User manual

311-145 JR. SLIDER (Perm)
Page 1 of 5
Rev 08/12/2020
IMPORTANT
PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. Please retain this
instruction sheet in your files. It contains important replacement parts information.
All equipment must be installed in accordance with these instructions.
It is important to use and maintain all public playground equipment properly. Playground
equipment, which is improperly maintained, can cause serious injury. Periodical
inspections, maintenance, repair and/or replacement of damaged parts is necessary for
safe operation of equipment. Appropriate publications, available at no charge, from the
Consumer Product Safety Commission, include “A Handbook for Public Playground Safety”.
You can receive your free copy by calling 1-301-504-7908
Use of safety surfacing in compliance with the current ASTM specification F1292 is required.
PACKING LIST
HARDWARE BAG
1
CTN
1
Hardware Bag
3
226-602
3/8” Nylon Insert Lock Nuts
1
314-460
Slide Leg Holder
3
126-703
3/8” X 1” Button Head Bolts
1
CTN
1
905-707
Stair
12
116-530
5/16” X 1” Button Head Bolts
1
BDL
1
403-317
Entrance Rails
7
116-604
3/8” X 1” Hex Head Bolts
1
103-306
2 3/8” OD. Slide Leg
7
326-601
3/8” Lock Washers
1
CTN
1
313-428
Platform
1
416-400
1/4” Socket Key
2
WF
403-248
Guard Rail Leg Assembly
2 PR
415-513
1 3/8” “T” Clamps
1
SLIDE
1
435-600
Slide Bedway
2
196-802
1/2” X !” Socket Set Screw
1
BDL
1
383-461
Right Stair Rail
2
116—545
5/16” X 2 !” Button Head Bolt
383-462
Left Stair Rail
17
316-601
3/8” Flat Washers
14
326-501
5/16” Lock Washers
1
416-402
7/32 Socket Key
10
216-512
5/16” Button Head Nuts
2
416-350
3/16 Socket Keys
2
805-532
Warning Label
2
805-534
SportsPlay Label
1
MAINTENANCE CHECKLIST
3 CTN 2 BDL 2 WF 1 SLIDE 8 TOTAL PCS WT 390# CLASS 70

311-145 JR. SLIDER (Perm)
Page 2 of 5
Rev 08/12/2020
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS
STATIONARY & PORTABLE EQUIPMENT –USE/FALL ZONES SHOULD EXTEND A MINIMUM OF 6 FEET IN ALL
DIRECTIONS FROM THE PERIMETER OF THE EQUIPMENT GROUND SPACE. THIS AREA SHOULD BE COVERED
WITH THE REQUIRED AMOUNT OF RESILIENT SAFETY SURFACING MATERIAL. FOR SOME EQUIPMENT –
USE/FALL ZONES CAN OVERLAP. SEE CONSUMER PRODUCT SAFETY COMMISSION GUIDELINES.
DIAMETER & DEPTH OF FOOTING ILLUSTRATED ARE SATISFACTORY IN MOST APPLICATIONS FOR PIPE
SIZES UP TO 2 3/8” DIAMETER. VARYING SOIL & CLIMATIC CONDITIONS MAY REQUIRE DEEPER &
HEAVIER FOOTINGS IN SOME AREAS. CHECK LOCAL BUILDING CODES.
PERMANENT INSTALLATION:
* If resilient surfacing is to be less than 12”, then additional pipe should be put in
concrete to maintain proper finish grade for equipment.
6’
74”
30”
6’
18”
6’
3’
6’
CONCRETE
FOOTING
1’ DIA X 2’ DEEP
USE AREA
14’ X 24’
26”
22”

311-145 JR. SLIDER (Perm)
Page 3 of 5
Rev 08/12/2020
GENERAL ASSEMBLY INSTRUCTIONS:
Check all the parts and hardware with the packing list to be sure you have received
everything needed to assemble this product. CONTACT YOUR LOCAL DISTRIBUTOR WITH
NOTIFICATION OF ANY MISSING OR DAMAGED PARTS. Contact must be made within ten days of
receipt of your order.
Only hand-tighten nuts & bolts on initial assembly. Final tightening should be done
EVENLY after final assembly when unit has been plumbed & leveled.
After assembly is complete, ANY ENDS OF BOLTS PROTRUDING BEYOND NUTS SHOULD BE CUT OFF
AND/OR PEENED OVER TO REMOVE ANY SHARP EDGES. Go over entire unit to file smooth any
sharp edges or projections that may have been caused by rough handling in shipping or
installation. T-Clamps are designed for both one and two bolt connections. In many
situations only one bolt is required. See specific assembly instructions.
On products with platforms install 1 –2 degrees off level to facilitate water drainage.
GENERAL MAINTENANCE INSTRUCTIONS:
Check MONTHLY for loose bolts, damaged or broken parts. Tighten and/or replace
immediately.
SPECIFIC ASSEMBLY INSTRUCTIONS:
403-319
ENTRANCE RAIL
403-248 GUARD
RAIL/LEG
ASSEMBLY
403-478
PLATFORM
435-600
PLASTIC SLIDE
383-461/462
STAIR RAILS
905-707
STAIR ASSEMBLY

311-145 JR. SLIDER (Perm)
Page 4of 5
Rev 04/12/10
NOTE:
NOTE:
STEP #1:
STEP #2:
STEP #3:
STEP #4:
Slide should be installed in shaded areas or face NORTH to prevent direct
Sun on Slide’s Chute.
All threaded ends of bolts protruding beyond nuts must be cut off and/or
peened to eliminate sharp edges. No more than two threads should extend
beyond face of nut.
All washers, “T” nuts, and other fastener hardware used on round pipe or
tubing must be hammered down to conform to the curved underlying surface to
eliminate catch points.
Do not fully tighten hardware until the unit is completely assembled
Mark & dig footing holes per SKETCH on PAGE #2.
Assemble Platform on the ground. Attach Guardrail Leg Assemblies 403-248.
SEE PICTURE ON PG 3 AND REFER TO VIEW A FOR HARDWARE DETAILS
Stand unit up, place it in the footing holes, level the unit and then brace
it. Please note the orientation of the platform (one side of the platform is
marked slide and one side is marked stairs) and orientate it in the desired
direction. Attach the stairs using the 3/8 x 1” Button Head Bolts and
3/8”washers through the holes in the top of the stairs and through the
platform, another 3/8” washer and into a 3/8” lock nut. Bolt the right and
left stair rails on the proper side to the lower part of the stairs. (Refer
to the side and front view illustration in View C) Attach the top of the
stair rails to the guard wall.
Attach the Slide Leg Holder to the bottom of the slide (view E) with 3/8 x
1” hex bolts, 3/8” washer and 3/8” lock washers. Place the slide leg into
the slide leg holder and tighten set-screws (view F). Place slide leg into
footing holes and attach the slide to the “Slide” side of the platform
inserting the 3/8 x 1” hex bolts through the 3/8” washer, 3/8” lock washer,
the back of the platform and into the factory installed nuts on the slide.
(VIEW D). Using the “T” Clamps install the 403-319 Slide Entrance Rail above
the slide (View B)
STEP #5:
Plumb & level. Tighten all nuts & bolts so that lock washers are flat.
Pour Concrete. Wait 48 hours before removing braces, installing Resilient
Surfacing & using equipment.
STEP #6:
Attach Warning Label and Manufacturer’s Identification Label to a clean
surface. The Labels should be attached in a location where they are clearly
visible and legible and away from normal hand and foot placement areas. The
Labels must be replaced if they become illegible, destroyed or removed.
Contact your distributor for replacement Labels.

311-145 JR. SLIDER (Perm)
Page 5 of 5
Rev 08/12/2020