SportsPlay 801-312-H User manual

801-312-H See Saw 6 Seat
Page 1
Rev. 09/10/2010
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
IMPORTANT
PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. Please retain
this instruction sheet in your files. It contains important replacement
parts information. All equipment must be installed in accordance with these
instructions. It is important to use and maintain all public playground
equipment properly. Playground equipment, which is improperly maintained,
can cause serious injury. Periodical inspections, maintenance, repair and/or
replacement of damaged parts is necessary for safe operation of equipment.
Appropriate publications, available at no charge, from the consumer product
safety commission, include “A Handbook for Public Playground safety”. You
can receive your free copy by calling 1-301-504-7908.
PACKING LIST
HARDWARE BAG
1
CTN
1
Hardware Bag
12
105-017
2 3/8” Pipe Plug
2
503-501
Elbow
12
196-802
1/2” x 1/2” Socket Set Screw
3
803-522
Fulcrum
24
116-550
5/16” x 3” B.H. Bolt
3
803-523
Sleeve
12
116-543
5/16” x 2 1/4” B.H. Bolt
6
803-524
Handle
36
326-501
5/16” Lock Washer
6
803-925
Seat Boards
36
216-512
5/16” x 1” B.H. Nut
1
BDL
3
803-601
Pipe 2 3/8” OD x 3’6” Long
1
416-400
1/4” Socket Key
6
PIPE
1
803-226H
Pipe Supports
2
416-350
3/16” Socket Key
1
PIPE
1
803-602
Pipe 7’ Long 2 3/8” OD
2
516-350
PermaBond Threadlocker Tube
1
1
343-501
“T” Fitting
2
805-532
Warning Label
2
805-534
SportsPlay Label
1
Maintenance Checklist
1 CTN 1 BDL 7 PIPE 9 TOTAL PCS 350# Weight Class 70

801-312-H See Saw 6 Seat
Page 2
Rev. 09/10/2010
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:
Stationary & portable equipment –use/fall zones should extend a minimum of 6
feet in all directions from the perimeter of the equipment ground space.
This area should be covered with the required amount of resilient safety
surfacing material. For some equipment –use/fall zones can overlap. See
Consumer Product Safety Commission guidelines. Diameter & depth of footings
illustrated are satisfactory in most applications for pipe sizes up to 2 3/8”
diameter. Varying soil & climactic conditions may require deeper & heavier
footings in some areas. Check local building codes.
DETAIL: Permanent Installation Suggested Bracing Method
•If resilient surfacing is to be less than 12”, then additional pipe
should be put in concrete to maintain proper finish grade for
equipment.
USE AREA & FOOTING LAYOUT:

801-312-H See Saw 6 Seat
Page 3
Rev. 09/10/2010
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL INSTRUCTIONS:
Car tires (not furnished) or some other shock-absorbing material should be
embedded in the ground beneath the seats to minimize the risk of injury due
to abrupt contact with the ground. Also, lengths of standard 2 x 4’s can be
easily positioned between the pipe rails to prevent children from putting
their feet between the rails.
GENERAL MAINTENANCE INSTRUCTIONS:
Check MONTHLY for loose bolts, damaged or broken parts. Tighten and/or
replace immediately.
SPECIFIC ASSEMBLY AND INSTALLATION:
NOTE:
All button head nuts are placed on the pipe side of the spots where
attached and the lock washers are placed on the Bolts. DO NOT tighten
nuts more than hand-tight until entire assembly is completed.
STEP #1:
Assemble frame by first attaching one leg to 8’ long top rail using
elbow. Tighten with set screws. Slide fulcrum over top rail to elbow by
leg, then sleeve so holds fulcrum in place. Tighten sleeve with set
screw to bottom of top rail. Attach middle leg to center fitting and
slide over top rail. Position so middle leg will be 3’7” from first leg.
Tighten to top rail. Then slide another fulcrum onto the top rail down
to the center fitting, followed by another sleeve. Tighten sleeve to
bottom of top rail so holds fulcrum against center fitting. Finally
slide last sleeve, then fulcrum onto top rail, position last leg into
elbow and onto top rail. Slide last fulcrum and sleeve back up against
elbow and secure with set screws. DO NOT attach see saws at this time.
STEP #2:
Using assembled frame as your template, mark and dig footing holes.
STEP #3:
Prop in holes, leaving 15-18” distance from resilient surface to top of
frame, plumb, level and pour concrete. Allow at least 48 hours for
concrete to harden.
STEP #4:
After concrete has hardened, attach the rest of the equipment. Use the
5/16” x 2 1/4” button head bolts, lock washers and button head nuts to
attach the long pipe supports to the fulcrums. Use the 5/16” x 3” button
head bolts, lock washers and button head nuts to attach the seat and
handle to the pipe supports. Use Threadlocker on all button head
fasteners. Drive pipe plugs into the open ends of the pipe supports.
STEP #5:
Attach Warning Label and Manufacturer’s Identification Label to a clean
surface. The labels should be attached in a location where they are
clearly visible and legible and away from normal hand and foot placement
areas. The labels must be replaced if they become illegible, destroyed
or are missing. Contact your SportsPlay distributor for replacement
labels.