SportsPlay JR SLIDER User manual

5
2
22
21
15
Detail A
15
8
21
22
5
12
(Details Continued
(Details Continued(Details Continued
(Details Continued
on Sheet 2)
on Sheet 2)on Sheet 2)
on Sheet 2)
21
JR SLIDER
JR SLIDERJR SLIDER
JR SLIDER
543
311-145
311-145311-145
311-145
Sheet 1 of 3
Sheet 1 of 3Sheet 1 of 3
Sheet 1 of 3
I EM NO. PAR
NUMBER DESCRIP ION Q Y.
1 435-600 Slide Bedway 1
2 313-428 Platform 1
3 905-707 Stair 1
4 403-317 Entrance Rail 3
5 403-248 Guard Rail Leg Assembly 2
6 103-306 Slide Leg 1
7 314-460 Leg Holder 1
8 383-461 Right Stair Hand Rail 1
9 383-962 Left Stair Hand Rail 1
10 126-504 5/16" x 1" Carriage Bolt 3
11 435-405 Attachment Bracket 1
12 415-513 1-3/8" " " Clamp 6pr
13 226-602 3/8" Nylon Insert Lock 2
14 126-704 3/8" x 3/4" Button Head Bolt 2
15 116-530 5/16" x 1" Button Head Bolt 12
16 116-604 3/8" x1" Hex Bolt 7
17 326-601 3/8" Lock Washer 7
18 196-802 1/2" x 1/2" Socket Set Screw 2
19 116-545 5/16" x 2-1/2" Button Head Bolt 2
20 316-601 3/8" Flat Washer 15
21 326-501 5/16" Lock Washer 14
22 216-512 5/16" Button Head Nut 10
23 226-501 5/16" Lock Nut 6
24 316-501 5/16" Flat Washer 8
25 416-350 3/16" Socket key 2
26 805-532 Warning Label 2
27 805-534 SportsPlay 2
28 000-000 Maintenance Check List 1
8
3
22
19
21
20
Detail B
D
DD
D
Detail C
4
5
1
8
3
C
CC
C
B
BB
B
A
AA
A
4
9
12
F
FF
F
E
EE
E
2
G
GG
G

7
17
20
1
16
6
1
18
21 15
5
4
22
12
*IMPORTANT*
*IMPORTANT**IMPORTANT*
*IMPORTANT*
two bolt connections. In man situations onl one bolt is required.
remove an sharp edges. Go over entire unit to file smooth an sharp
(Details Continued
(Details Continued(Details Continued
(Details Continued
7
Detail D
17
Detail G
Detail E
in shipping or installation. T-Clamps are designed for both one and
edges or projections that ma have been caused b rough handling
Detail F
1
10
16
23
24
2
11
20
From Sheet 1)
From Sheet 1)From Sheet 1)
From Sheet 1)
and/or replace immediatel .
GENERAL MAINTENANCE INSTRUCITONS:
GENERAL MAINTENANCE INSTRUCITONS:GENERAL MAINTENANCE INSTRUCITONS:
GENERAL MAINTENANCE INSTRUCITONS:
install 1 - 2 degrees off level to facilitate water drainage.
See specific assembl instructions. On products with platforms
include "A Handbook For Public Pla ground Safet ". You can receive
under all pla ground equipment. Appropriate publications, available
GENERAL ASSEMBLY INSTRUCTIONS:
GENERAL ASSEMBLY INSTRUCTIONS:GENERAL ASSEMBLY INSTRUCTIONS:
GENERAL ASSEMBLY INSTRUCTIONS:
our free cop b calling 1-301-504-0580.
of equipment and safet of users. Resilient Surfacing should be used
at NO Charge, from the consumer product Safet Commission,
and/or replacement of damaged parts is necessar for safe operation
cause serious injur . Periodical inspections, maintenance, repair
properl . Pla ground equipment which is improperl maintained can
prevent direct Sun on Slide's Chute.
NOTE: Slide should be installed in shaded areas or face NORTH to
Check MONTHLY for loose bolts, damaged or broken parts. Tighten
SPECIFIC ASSEMBLY INSTRUCTIONS:
SPECIFIC ASSEMBLY INSTRUCTIONS:SPECIFIC ASSEMBLY INSTRUCTIONS:
SPECIFIC ASSEMBLY INSTRUCTIONS:
Please retain this instruction sheets in our files. It contains important
replacement parts information. All equipment should be installed in
accordance with these instructions.
It is important to use and maintain all public pla ground equipment
Check all the parts and hardware with the packing list to be sure ou
have received ever thing needed to assemble this product. Contact
Your Local Distributor with notification of an missing or damaged
parts. Contact must be make within 10 da s of receipt of our order.
Onl hand-tighten nuts & bolts on initial assembl . Final tightening
should be done EVENLY after final assembl when unit has been
plumbed & leveled. After assembl is complete, an ends of bolts
protruding be ond nuts should be cut off and/or peened over to
NOTE: All threaded ends of bolts protruding be ond nuts must be
cut off and/or peened to eliminate sharp edges. NO more
than two threads should extend be ond face of nut.
All washers, "T" nuts, and other fastener hardware used on
round pipe or tubing must be hammered down to conform to
the curved underl ing surface to eliminate catch points.
21
JR SLIDER
JR SLIDERJR SLIDER
JR SLIDER
543
311-145
311-145311-145
311-145
Sheet 2 of 3
Sheet 2 of 3Sheet 2 of 3
Sheet 2 of 3

1'-0"
1'-0"
1'-0"
2'-0"
1'-0"
3'-0"
24'-6"
6'-0" 3'-0" 3'-0" 6'-6" 78
2'-0" 1'-6"
6'-0"
15'-0"
6'-0"
21
JR SLIDER
JR SLIDERJR SLIDER
JR SLIDER
543
311-145
311-145311-145
311-145
Resilient
Safety
Surfa ing
Pipe
Top of
Non
Safety
Surfa ing
2'-0"
Dia.
1'-0"
or removed. Conta t your distributor for repla ement Labels.
Step 6: Plumb & Level. Tighten all nuts & bolts so that lo k washers
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:
in a lo ation where they are learly visible and legible and
bra es, installing Resilient Surfa ing & using equipment.
Step 7: Atta h Warning Label and Manufa turer's Identifi ation
Labels must be repla ed if they be ome illegible, destroyed
away from normal hand and foot pla ement areas. The
Varying soil & limati onditions may require deeper & heavier
PERMANENT INSTALLATION:
PERMANENT INSTALLATION:PERMANENT INSTALLATION:
PERMANENT INSTALLATION:
satisfa tory in most appli ations for pipe sizes up to 2-3/8" diameter.
footings in some areas. Che k Lo al Building Codes.
Label to a lean surfa e. The Labels should be atta hed
are flat. Pour Con rete. Wait 48 hours before removing
Sheet 3 of 3
Sheet 3 of 3Sheet 3 of 3
Sheet 3 of 3
Step 1: Mark & dig footing holes per footing diagram.
Step 2: Assemble Platform on the ground. Atta h Guardrail Leg
Assemblies. See Detail A. Atta h Slide Leg. See Detail E
& F.
Step 3: Turn right side up & bra e in footing holes. Length of pipe
below intended level of Resilient Surfa ing should be 24"
Atta h Slide Entran e Rail. See Detail G.
Step 4: Atta h Stair Assembly & Stair Hand Rails to Guardrail Leg
Assembly. See Detail B & C.
Step 5: Atta h plasti Slide to Platform. See Detail D.
Stationary & Portable Equipment - Use/Fall Zones should extend
a minimum of 6 feet in al dire tions from the perimeter of the equip-
ment ground spa e. This area should be overed with the required
amount of Resilient Safety Surfa ing Material. For some equipment
Use/Fall Zones an overlap. See onsumer produ t safely omm-
ission guidelines. Diameter & depth of footing illustration are
*If Resilient Surfa ing is to be less than 12", then additional pipe
should be put in on rete to maintain proper finish grade for
equipment.*
Surfa ing
Resilient
Safety
Upright
UprightUpright
Upright
Con rete
Con reteCon rete
Con rete
Footing
FootingFooting
Footing
Angled
AngledAngled
Angled
Pipe
Footing
FootingFooting
Footing
Con rete
Con reteCon rete
Con rete
Top of
Non
Safety
Surfa ing
Dia.
1'-0"
FOOTING DIAGRAM
FOOTING DIAGRAMFOOTING DIAGRAM
FOOTING DIAGRAM