SportsPlay 301-146 10' MGR User manual

October 4, 2010
1
301-146 10’ MGR
INSTALLATION INSTRUCTION
INSTALLATION DETAILS
!Recommended crew (Adult): 2-3
!Installation time: 8-12 Hours not including
concrete cure time
!User age: 5-12
!Use zone: 22’ Diameter
!Weight: 990
!Actual Dimension: 120” Diameter
WARNING
Use of safety surfacing (wood mulch) in
compliance with ASTM specification
F1292 is required.
MAINTENANCE:
!As the owner of the playground you are
responsible for maintenance of the equipment and
play area. A maintenance schedule must be
developed and the equipment inspected frequently.
Periodic Inspections, maintenance, repair and
replacement of damaged parts is necessary for the
safe operation and use of the equipment
!A maintenance section that includes component
specific maintenance requirements is included at
the end of this document.
UNIT IS DESIGNED FOR 12” OF LOOSE RESILIENT
SURFACING. WOOD MULCH IS THE MANUFACTURERS
PREFERED MATERIAL.
THIS UNIT WILL NOT INSTALL ON POUR IN PLAY. UNIT
WILL ALSO NOT INSTALL OVER ANY OTHER
SURFACING THAT IS LESS THAN 12” HIGH

October 4, 2010
2
301-146 10’ MGR
INSTALLATION INSTRUCTION
PARTS LIST
NOTE: Keep a copy of these instructions on file to assist you
with maintenance and replacement parts.
ID
PART #
DESCRIPTION
QTY
1
913-801
10’ MGR Quarter Deck
6
2
913-323
MGR Handrail
6
3
913-379
10’ MGR Post Assembly
1
4
336-046
Center Hub Disk for 10’ MGR
1
5
913-377
10’ MGR Hub Assembly
1
6
913-378
10’ MGR Support Arm
6
7
336-044
1 1/2” Ball Bearing
1
8
336-030
Grease Fitting
2
9
316-801Z
1/2” Flat Washer Zinc
6
10
226-802Z
1/2” Nylon Lock Nut Zinc
6
11
126-810
1/2 x 4” Carriage Bolt
6
12
126-701bps
3/8 x 1 1/4” Button Head Bolt
107
13
316-601
3/8” Flat Washer
214
14
226-602
3/8” Nylon Lock Nut
107
15
416-505bpk
7/32” Socket Key
2
16
Handrail Touch-up Paint
1
17
126-709
3/8 x 2 1/2” Button Head Bolt
6

October 4, 2010
3
301-146 10’ MGR
INSTALLATION INSTRUCTION

October 4, 2010
4
301-146 10’ MGR
INSTALLATION INSTRUCTION
FOOTING INFORMATION
!Total footing depth is 36” plus the height of the surfacing
which is 12” for a total height of 48”. The 36” includes 10”
of blocking material, which in this case is dry concrete. So
overall only 26” of the post assembly is inserted into the
footing hole. See drawing on next page for
footing/surfacing side view.
!It is the owner/installers responsibility to check local
building codes and to comply with those codes. All footing
depths listed here are recommendations and local soil types
and frost lines may require a deeper and/or wider footing
depth. If that’s the case you must add more blocking
material to accommodate the deeper footing, as the post
length will still only be installed at the depth listed in this
instruction manual.

October 4, 2010
5
301-146 10’ MGR
INSTALLATION INSTRUCTION

October 4, 2010
6
301-146 10’ MGR
INSTALLATION INSTRUCTION
SPECIFICATIONS
!Deck – 12ga HRPO welded steel deck
!Deck Coating – Thermoplastic
!Handrail – 30” high 1 5/8” od FloCoat galvanized steel tube
welded to a 3/8 flange
!Handrail Coating – Electrostatically applied and oven cured
polyester powder coating
!Post Assembly – 2 1/2” OD solid steel shaft with machined
pocket for bearing.
SPECIAL SAFETY & ASTM COMPLIANCE NOTES
!The deck height must be between 10” & 14” high from
the safety surfacing for compliance
INSTALLATION TIPS & TROUBLE SHOOTING
!12” of loose fill surfacing is required for this unit. The
manufacturer recommends using a certified wood
fiber/chips surfacing rather than sand or pea gravel
because wood will hold its shape better and is less likely
to cause damage by getting caught inside the mgr post
like sand or gravel is likely to do.
!Do not completely tighten bolts until told to do so. When
instructed tighten deck bolts incrementaly as you move
around the MGR to prevent gaps in between the deck
sections.
!Stainless Steel hardware can occasionally be difficult to use
particularly if you need to take them out to make an
adjustment. It is recommended that you add a drop of oil to
bolts that may have to be removed before you install them.
!Do not tighten bolts all the way until the unit is completely
assembled and all components are square and level.
!Identify and separate all parts by referencing the detail
drawings and the parts list.
!As you unpack and separate the components, use the
cardboard sheets that were used for packing and shipping to
prevent damage to the components. This is particularly true
all Powder Coated and Thermoplastic coated components,
by setting the components on top of the cardboard.

October 4, 2010
7
301-146 10’ MGR
INSTALLATION INSTRUCTION
BEFORE YOU BEGIN
In addition to the components on the packing list you will need a
shovel, concrete, magnetic level and a socket or wrench set.
INSTALLATION STEPS
__1. Once the desired location has been determined while
keeping a 22!dia use zone in mind, dig a 36" diameter hole
to a depth of 36"
__2. After all loose material is removed from the hole, add
10” of dry concrete to the bottom for the base. Place the post
assembly (3) with the bearing pocket facing up and out of the
hole. Plumb and level post – NOTE: Post must be
perfectly level in all directions before adding concrete
for safety and durability of product.
__3 Add concrete to hole, leave 2” of space in the hole below
the surface grade for backfill. Crown the top of the concrete
down and away from the post to help prevent water build up
around the post. Periodically check the post to ensure it is
level while concrete is curing. Wait a minimum of 48 hours
before continuing installation.
__4 After concrete has cured, place the Ball Bearing (7) into
the pocket on the post and coat the post and bearing with
general purpose grease. Next slide the Hub assembly (5)
onto the post. (refer to detail A)
__5 Attach the MGR support arms (6) to the hub assembly
(5) by sliding the arm oveer the tabs on the hub (do not
attach to the side of the tabs) and secure using 2 1/2”
bolts, 3/8 washers and 3/8” nuts. (See Detail D)

October 4, 2010
8
301-146 10’ MGR
INSTALLATION INSTRUCTION
__6. When installing the deck sections (1) make sure NOT to place
tab on support arm (6) in between the deck sections, tab should fit
on the inside of the flanged lide of the deck. Also, completely
install all deck sections before tightening the bolts completely.
When tightening the bolts move around the entire unit and tighten
them evenly to ensure the deck sections are properly aligned and to
ensure there are no gaps between the deck sections. Connect the
support arm (6) to the deck sections as well as the deck sections to
each other using 1 1/4” bolts (12), 3/8 washers and 3/8 nuts. (refer
to Detail C for connecting the support arms to the decks and Detail
G for connecting the deck sections)
__7. Attach the Hub Disk (4) to the deck sections (1) and the Hub
Assembly (5) by placing hub disk on top of the decks over the hub
assembly and attach by inserting the 4” carriage bolts down through
the decks and hub assembly. Secure from the bottom of the hub
assembly with 1/2” washers and 1/2” lock nut. (see Detail E)
__8. Attach the Handrails (2) to the Deck Sections (1) using 1 1/4”
bolts, two 3/8 washers and a 3/8 lock nut. Nut should be located
under the deck if properly installed. (see Detail F)
__9. Governor Tension Adjustment: Back off the jamb nut on
the governor assembly (attached to post assembly) and turn the
adjustment nut until the rubber wheel is pushing firmly onto the
sleeve of the hub assembly. Once wheel is firmly against the hub,
tighten the jamb nut to secure it into position. (see Detail B)
__10. Install surfacing to a depth of 12 “ in side the use zone.
Taper surfacing under the deck down to the post to give access to
the govenor and grease fitting on the hub assembly.

October 8, 2010
1
301-146 10’ MGR
EQUIPMENT MAINTENANCE
Operational
!Grease Merry Go Round Weekly
or daily in an environment that
has sand or other small damaging
materials.
Hardware
!Inspect for loose or missing
hardware. Tighten all loose
hardware and replace all missing
hardware. Block off access to
equipment if necessary.
Welds
!Inspect all welds for cracks. If a
crack is found block access to the
playground and contact your
distributor for replacement parts
immediately.
Finish
!Inspect all metal components for
coating damage. If powder coating
needs to be repaired sand surface and
mask off area. Coat with primer and
once the primer has dried paint with
color matching touch up paint.
Contact distributor of color matching
paint. Contact Distributor for
Thermoplastic repair kit.
Governor
!Inspect Governor weekly when
greasing unit. Ensure that all pieces
are installed and secure
!Ensure rubber wheel is in contact with
the sleeve. If not, tighten by first
backing off jam nut, tighten
adjustment bolt until wheel is in
position and then tighten the jam nut.
Replacement Parts
!Reference the parts list on page 2 of
the instruction set for this component
to identify the part/s correctly.
!Contact your distributor to order parts.
Footings
!Inspect all footings to ensure
equipment is secure. You must block
access to prevent access until repair is
made.
Surfacing - Refer to the surfacing maintenance
sheet provided by your surfacing supplier.

October 8, 2010
2
301-146 10’ MGR
EQUIPMENT MAINTENANCE
INSPECTION FORM
!MAKE COPIES OF THIS FORM TO USE FOR INSPECTION
!REVIEW THE “MAINTENANCE GUIDE” IN THE APPENDIX TO BETTER UNDERSTAND THE IMPORTANCE OF
MAINTENANCE AND HOW TO DEVELOP A MAINTENANCE SCHEDULE.
!DOCUMENT ALL MAINTENANCE ACTIONS ON THE LIST AS WELL AS ANY NOT LISTED.
!INCLUDE DATES AND SIGNATURES
Inspection Checklist
Recommended
Frequency
Grade
(Pass/Fail/NA)
Date
Inspected
Date Repairs
Completed
Inspect Governor
Weekly
Inspect Hardware
Weekly
Grease Shaft
Weekly
Inspect Finish
Monthly
Inspect Footing
Yearly
Inspect Surfacing
Daily
Inspector: _______________________ Signature: ___________________________________ Date: ___________________________
Maintenance Record
Part
Problem
Corrective Action
Date