SPORTSPOWER 2BLAH User manual

APPROXIMATE ASSEMBLY TIME 2 PERSON ASSEMBLY REQUIRED ASSEMBLY SPACE
2BLAH
TODDLER SWING WITH BOOSTER SEAT
30
FLOOR AREA
2M×2.5M×2M
MEASURE
REQUIRED ASSEMBLY TOOLS
minutes
ASSEMBLED DIMENSIONS
DESCRIPTION:
WEIGHT 6.1KG, BUILD IN LOCATION
1400mm
1000mm
1190mm
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

5
7
7
4
3
2
3
1
6
2
4
8
8
5
7
7
4
48
8
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 2 OF 15
Peg Tube
NS-CAP
SW-XBAR
NS-TPLEG-LHS
SW-LOWLEG
NS-TPLEG-RHS
NS-SEAT
SW-TOPBAR
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT

HARDWARE LIST
D
BOLT
M6×42mm
X4
BA C
"U" BOLT
M8×102mm
X2
BOLT
M6×38mm
X4
BOLT
M6×53mm
X4
1cm
2cm
3cm
4cm
5cm
6cm
7cm
8cm
9cm
10cm
0cm
G
BOLT
ø8×100mm
X2
DESCRIPTION:
2BLAH
TODDLER SWING WITH BOOSTER SEAT
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 3 OF 15
GEN-UBOLTM8X102 GEN-BOLTM6X38 GEN-BOLTM6X53 GEN-BOLTM6X42 FNS-SEATPINS
VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT

ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 4 OF 15
GEN-ARCWASH-19X8.5 GEN-ARCWASH-14X6.5 GEN-SPRWASH-M8 GEN-SPRWASH-10.5X1.5 GEN-CAPNUT-M8 GEN-NUT-M6
VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT

1cm
2cm
3cm
4cm
5cm
6cm
7cm
8cm
9cm
10cm
0cm
X1 X1
SPANNER
LM
ALLEN KEY
2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 5 OF 15
GEN-SPAN5-11-13 GEN-ALWR6MM
VIEW PRODUCT VIEW PRODUCT

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
Please read this instruction manual before you start to assemble or use this swing set.
You must follow all of the safety instructions while using this equipment. Be absolutely
sure that the surface on which this swing set is set up is properly surfaced with fine
sand, wood chips or double shredded bark mulch. Do not use this swing set on hard
packed soil concrete or any other kind of hard surface. Read all cautionary statements
before using this equipment.
Observing the following safety instructions will reduce the likelihood of serious injury.
1. Only for domestic use. For outdoor use only.
2. This swing is designed for children between the ages of 9-36 months.
3. Max weight of user shall not exceed 25 kg.
4. For use under adult supervision.
5. Do not orientate the swing directly towards the sun as this may lead to a child
becoming dizzy/disorientated through extended use.
6. Do not install the product on concrete, asphalt or hard surfaces.
7. Do not allow children to stand on the swing seat.
8. Do not allow children to get off of the swing whilst it is still moving.
9. Do not twist swing ropes or wrap them over the top cross beam.
10. Do not allow children to use the item if they are wearing loose, hooded or baggy
clothing. Clothing can get caught leading to user injury.
11. Do not allow children to climb on the swing. The swing should be sat upon with the
child’s body weight centrally in the seat.
12. Do not allow children to wander into the play area when the swing is in use.
13. Place the swing on a level surface at least 2 metres from any structures or
obstructions such as fence, garage, house, overhanging branches, laundry lines or
electrical wires etc.
14. Children should be instructed by a parent or an accompanying adult NOT to attach
items to the swing that are not specifically designed for use with it, such as, but not
limited to, jump ropes, clothes lines, pet leashes, chains and cables. These could all
cause strangulation.
15. Packing materials are not toys. Please remove and dispose of all packaging materials
before letting children use this swing.
16. At least 2 adults are required for assembly.
17. For use by only one child at any one time.
18. Check all nuts, bolts and fittings for tightness and tighten if required.
19. Check all coverings for bolts and sharp edges and replace when required.
20. Oil all metallic moving parts.
21. Check swing seats, ropes and other means of attachments for evidence of
deterioration. Replace when required in accordance with the manufacturer’s
instructions.
WARNING!
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 6 OF 15

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
22. Please take note : As an extra precaution, check this toy regularly for signs of wear
and damage.
23. For safety reasons, this swing MUST be anchored into the ground.
24. Anchors shall be placed level with or under the ground in order to reduce the risk of
tripping.
25. Leave all fittings finger-tight until assembly is complete, for ease of construction.
Then tighten firmly.
26. Swing must not exceed an angle of 60 degrees from the ground.
27. Failure to assemble and maintain this item as per these instructions may cause injury
to the user.
28. Maintenance to be carried out under the direct supervision of a responsible adult.
29. All main parts of this swing should be checked and maintained regularly.
If these checks are not carried out, the toy could overturn or otherwise become a
hazard.
30. Do not adjust the length of the swing rope.
31. Once assembly is complete, carefully check the equipment before use. If you find any
problems, do not allow children to use the equipment until it is fit for use.
32. Please retain these instructions for future reference.
33. Only for domestic use.
TIPS: BEFORE STARTING ASSEMBLY,PLEASE CHECK ALL PARTS ARE
INCLUDED, IF ANY PARTS ARE MISSING,PLEASE CALL ([phone]
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 7 OF 15

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
IT IS PARTICULARLY IMPORTANT THAT THIS PROCEDURE BE FOLLOWED AT THE
BEGINNING OF EACH SEASON.
● Never use pliers to tighten up screws –these can cause damage to both the paintwork
and the special anti-corrosion plating.
● Tighten all nuts and bolts securely. Replace as needed. If not checked regularly, bolts
can be loose or missed and components can become detached and cause injuries.
● Check the unit at the beginning of the usage season and monthly thereafter for
evidence of deterioration.
● Immediately remove and replace any items that appear to be weak or broken. Contact
customer support for replacement parts.
● Check all covers designed for bolts and sharp edges regularly to be certain they are
present and in good condition. Replace as needed. It is particularly important that all
covers are checked prior to the first use each season.
● Inspect handle bar, hardware, and etc., for proper closure and for signs of wear,
deterioration, rust and/or damage. Replace as needed.
● Lubricate all metallic moving parts monthly during the usage season. Applying a light
coat of automobile wax to all metal tubing surfaces will help protect your unit and add to
its longevity. Sand anyrusted areas of the metal tubing and repaint using a non-lead
based paint.
● Remove plastic seats and store indoors, or do not use when the temperature drops
below 32°F/0°C.
● Check unit for scuffs, burrs, sharp edges and anyother defects that may occur from
assembly, abuse, shipping or everyday use. Burrs and sharp edges may be filed down
until smooth and covered with duct tape if necessary.
● To help maintain the products appearance, occasionally clean the seats and metal
framework with a damp cloth lightly – but DO NOT useabrasive chemical cleaners.
● When the time comes to disassemble and disposeof this product, please completely
disassemble the unit and discard of it in a safe place and manner so as not to present
any hazard to any individual. It is important to check and maintain the main parts at
regular intervals. If these checks are not carried out, the toy could overturn or otherwise
become a hazard.Whenever practical, the instructions shall also be affixed to the toy.
CARE AND MAINTENANCE
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 8 OF 15

G
G
G
Insert the buckle(M) to lock the swing seat.
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 9 OF 15

TIPS: ENSURE TO ATTACH THE SEAT TO THE U BOLT (A) FIRST.
Step 2
A
x 2pcs
E
x 8pcs
H
x 4pcs
J
x 4pcs
DESCRIPTION:
2BLAH
TODDLER SWING WITH BOOSTER SEAT
A
A
E
H
J
E
E
E
H
J
6
2
2
3`
3
3
3
2
1
1
2
1
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 10 OF 15

2
2
3`
3
4
4
4
4
F
x8pcsx4pcs
B I K
x4pcs x4pcs
BFFIK
4
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 11 OF 15

TIPS:
1# ATTACH THE PLASTIC CAP (8) TO CROSS BAR (5) FIRST.
2# THE CROSS BAR (5) NEEDS TO BE ATTACHED TO
OUTER SIDE OF
THE SWING FRAME.
Step 4
2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
THE
DFI
F
K
4
5
8
4
8
8
4
4
4
5
5
F
x8pcsx4pcs
D I K
x4pcs x4pcs
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 12 OF 15

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
F
x8pcsx4pcs
C I K
x4pcs x4pcs
4
7
CFFIK
7
7
7
7
4
4
4
4
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 13 OF 15

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
7
7
7
74
4
4
4
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 14 OF 15

2BLAH
DESCRIPTION:
TODDLER SWING WITH BOOSTER SEAT
SP-19-NS004-SD-17001
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
PAGE 15 OF 15