SPORTSPOWER Sunnyslope Wooden Play Set WP-572 Mounting instructions

1
Sunnyslope Wooden Play Set
Style # (WP-572)
OWNER’S MANUAL
ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USER INSTRUCTIONS
DO NOT RETURN TO THE STORE
For CustomerService, pleasecall 1-866-370-2131 or visit www.sportspowerltd.net
Monday – Friday9:00 AM – 5:00 PM Eastern Time
Sportspower Limited
Level 20,Parkview Centre, 7 LauLiStreet, Causeway Bay, Hong Kong
FOR RESIDENTIAL USE ONLY
ASSEMBLY REQUIRES AT LEAST FOUR ADULTS

1
Dear Valued Customer,
Congratulations on your wood swing set purchase! Please read and completely understand the
contents of this owner’s manual. This manual contains specific instructions that must be followed to
prevent injuries.
This equipment is for residential use only. This swing set is NOT intended for public or commercial
use. The warranty will be voided if the swing set is used in a commercial application.
The product was designed to be used by children between the ages of 3-10. Children must NOT play
on this set until it is properly assembled and inspected by an adult. Adult supervision is required at all
times while children are playing on the equipment. Do not allow children under six (6) years old to be
near during the assembly of this product due to choking hazards of small parts.
The equipment must be installed on level ground. Uneven ground must be leveled prior to
installation. Installation on sloping or uneven ground will put stress on the joints, causing the unit to
become loose and unstable which may result in serious injuries. You must ensure there are no
obstructions or structures (e.g. electrical wires, branches, house, fence, garage, etc) within six (6) feet in
any direction from the equipment.
The U.S. Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook
recommends to install and maintain the playground equipment over at least9inches of wood chips,
mulch or shredded rubber (for equipment up to8feet high) or sand or pea gravel (for equipment no more
than 5 feet high) as shock absorbing material. Dirt and grass, which are the most prevalent surfaces
under home playground equipment, do not adequately protect children from serious head injuries. Install
protective surfacing at least six feet in all directions from play equipment. For swings, the surface should
extend, in back and front, twice the height of the suspending bar. Do not install your swing set over hard
surface, e.g. asphalt, concrete, packed earth, tile or brick floor. Do not allow children to use the product
during windy or wet weather conditions. You should consult a local licensed contractor about ways to
anchor the product in your location.
Please thoroughly read and follow the instructions in this Owner’s Manual to ensure proper and
enjoyable play for your children. The equipment must be checked before each use and maintained
regularly. This includes, but is not limited to inspecting the swing set for cracks, excess wear, missing
parts, loose connections, and for overall integrity. When the set shows any signs of weakness or
damage, you must stop using the swing set immediately, properly store the set or restrict access by users
until the condition is resolved.
Your product is warranted against defects in material and workmanship. Extended warranty is also
offered to those customers registering their products at www.sportspowerltd.net within 14 days from the
date of purchase. Please refer to our warranty policy at the back of this manual for details.
If you experience any problems with your product, do not return to the
store. For customer service, please call 1-866-370-2131 Monday-Friday
9:00am-5:00pm Eastern Time or visit www.sportspowerltd.net
INTRODUCTION

2
Trhbrt
IMPORTANT WARNINGS AND INSTRUCTIONS ……………………………………………………………………….. 4
IMPORTANT CONSUMER INFORMATION SHEET ……………………………………………………………………. 9
GROUND COVER INFORMATION .....…………………………………………………………………………………….……. 14
COMPLETE PRODUCT VIEW …………...…………………………………………………………………………………………. 15
TOOLS NEEDED ……………………………………………………………………………………………………………………..…….. 16
WOOD PARTS LIST…………………………………...………………………………………………………………………….......... 17
HARDWARE PARTS LIST ………………………...……………………………………………………………………………….…. 19
SPARE PARTS LIST …………………………………...…………………………………………………………………………………. 20
HARDWARE PRE-ASSEMBLE ….……………...…………………………………………………………………………………. 21
ASSEMBLY AND INSTALLATION INSTRUCTIONS ……………………………………….……….. 22
AREA OF INSTALLATION – PLAYHOUSE ….................…….……………………………...….. 23
AREA OF INSTALLATION – THE SWING SUPPORT BEAM ……………………………....….. 38
AREA OF INSTALLATION – SWING AND TRAPEZE BAR ……….…………………………... 41
AREA OF INSTALLATION – SLIDE ……………………………………………………................. 42
PRODUCT WARRANTY ……………………………………………………………………………… 44
TABLE OF CONTENTS

3
Trhbrt
BEFOREYOUBEGIN: Carefully read all instructions in this manual before assembling and using this
product. The unit must be assembled by adults. Heavy duty working gloves must be worn to avoid
injuries during assembly.
WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USINGTHIS EQUIPMENT
AGE LIMIT
This product is designed to be used by up to seven (7) children between the ages of 3 to 10.
Maximum individualuserweight is 100pounds (45kg) each withacombined maximum
weight of 700 pounds (315kg.)
The play set is designed for children over three (3) years of age. Use by smaller children
can result in entrapment and serious injury.
On-siteadult supervision is required at alltimes for children of allages.
Do notallowuse by childrenwithanyphysical condition that may affect his/her ability to use
thisequipment safely.
IMPORTANT:
Children must NOT play on this set until it is properly assembled and inspected by an adult.
The Wood Play Set must be properly installed and anchored BEFORE children can play on
the Wooden Swing Set.
You MUST readandfollowall instructions in this manual before installing or attempting to
use the WoodenSwingSet.
Failure to follow theseimportant requirements may result in the warrantybeingvoidedand/or
serious injury. Please supervise your children carefullyduringthe installationandassembly of
the Wood Play set.
Please also pay close attention to the periodic maintenance that is required to keep you Wood
Play Set inasafe condition for maximum enjoyment of backyard fun!
IMPORTANT WARNINGS ANDINSTRUCTIONS

4
Trhbrt
WARNING
BEFORE YOU BEGIN ASSEMBLY:
Take a complete inventory of components using the parts list.
Sort and lay out the wood pieces. Label each piece of wood for easy reference. For easy
identification during the assembly process, write the board’s letter on masking tape and
adhere to each piece of the wood. Some wooden components may twist or warp in the
carton after packaging. Usually, these parts straighten out when assembled. You may also
see some cracking of the grain. This is normal.
Sort all hardware according to size. Do not worry if extra hardware is included.
Find a safe play location.
You MUST install the Wooden Swing Set on level ground. Uneven ground must be leveled
prior to installation. The manufacturer cannot assume responsibility for any failure from
incorrect installation. Installing on sloping ground will put stress on all the joints, which will
cause the set to become loose and unstable.
Find a location where the equipment can be placed more than 6 feet from any structure or
obstruction (ex: electrical wires, branches, house, fence, garage) The safe play area refers
to a zone extending 6’ beyond the gym set on all sides, including the space above the gym
set.
The safe play area must be free of all structures, landscaping, tress and branches, rocks,
wires and other obstacles to safe play. Children can be seriously injured running or
swinging into these obstacles.
Remove any rocks or any jagged or sharp object that could endanger your children’s’safety.
Remove all tripping hazards from the safe play area. Tripping hazards include but are not
limited to: roots, stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing, and
electrical connections.
Do NOT install your swing set over gravel, asphalt, packed earth or any other hard surface.
The following is a list of recommended ground covers from the Consumer Product Safety
Commission.
SUGGESTED MATERIAL UNCOMPRESSED DEPTH
Double Shredded Bark Mulch 9”
Uniform Wood Chips 12”
Fine Gravel 12”
Fine Sand 12”
IMPORTANT WARNINGS AND INSTRUCTIONS

5
Trhbrt
BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and
using this product. The unit must be assembled by adults. Heavy duty working gloves must be
worn to avoid injuries during assembly.
WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT
Observing the following statements and warnings reduces the likelihood of serious or fatal
injury.
PLAY SUPERVISION
DO NOT allow more than one child to play on the individual swing or slide at the same time.
DO NOT allow children to stand on the swing seat.
DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to
avoid being struck by other children while playing.
DO NOT allow children to twist the swing chains or ropes, or loop them over the top support
bar as this may reduce the strength of the chain or rope.
Owners shall be responsible for maintaining the legibility of the warning labels.
Warning the owner to instruct children not to use the equipment in a manner other than
intended.
DO NOT swing empty seats as this may cause injuries.
ALWAYS guide children to sit in the center of swinging parts, with their full weight placed in
the seat center and holding on to the swing chains.
DO NOT allow children to jump off the equipment while it is in motion. ALWAYS come to a
full stop before dismounting.
ALWAYS dress children appropriately for playing, e.g. wear well-fitted rubber sole shoes,
and remove loose or sharp items such as jewelry, hair accessories, scarves, ponchos that
may become entangled in the equipment or cause injuries.
ALWAYS make sure children remove their bike or other sports helmets before playing on the
playground. Helmets can become entrapped in the playground, posing a strangulation
hazard.
DO NOT allow children to climb onto swing or jump to and from different play areas of the
equipment. ALWAYS return safely to the ground before approaching another play area.
DO NOT allow children to climb on structural parts (e.g. legs, top bar). These are structural
components and are not designed for play.
ALWAYS check the slide or other parts exposed to the body for extreme heat from the sun
before allowing children to use the equipment.
ALWAYS prevent access and secure from any unauthorized use when there is no adult
supervision.
DO NOT allow pets or other animals near the equipment to prevent damage or injuries.
IMPORTANT WARNINGS AND INSTRUCTIONS

6
Trhbrt
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION
DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the
equipment and all parts are well secured and stable before each use.
ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially
hazardous to users.
DO NOT attach items to the equipment that are not specifically designed for use with the equipment,
including, but not limited to, jump ropes, clothesline, pet leashes, cables and chains as they may
cause choke hazards.
The wood, steel and plastic parts used in your product are subject to normal wear. Gradual
deterioration of the material will occur, the speed of which will depend on the level of exposure to UV
rays, airborne pollution, outdoor weather conditions such as rain and wind and the amount of use.
You must inspect the equipment prior to every use. This includes, but is not limited to inspecting the
set for cracks, excess wear, missing parts, loose connections, and for overall integrity. When the
set shows any signs of weakness, you must stop using the play set immediately, properly store the
set or restrict access by users until the condition is resolved.
Verify that the suspended climbing ropes, chain or cable are secured at both ends and
tightened, so that there is no loose ropes, chain or cable hanging that can result in choking
hazard.
WEATHER CONDITIONS
DO NOT use this equipment if the swing seat, slide or other parts are wet. Use the swing set only
when the parts are clean and dry. If the equipment is wet, the user could slip and suffer injuries.
Please be aware of weather conditions when using the equipment. If it is too windy, users could lose
control and suffer injuries. The playground equipment must be properly anchored, stored away or
restricted from use during inclement weather such as heavy winds or severe weather storms. You
should consult a local contractor about ways to anchor the product in your location.
DISPOSAL INSTRUCTIONS
Please use care when disassembling the equipment. Wear heavy duty working gloves to avoid
injuries.
Fully disassemble the entire swing and climber before disposal. Do not leave partially
disassembled equipment parts in areas accessible by children.
All plastic and steel parts could be recycled. Take it to your local recycling center. Do not let children
play with any disassembled parts destined for disposal, such as chains, slide, tubing, bolts, nuts,
screws, etc.
IMPORTANT WARNINGS AND INSTRUCTIONS

7
Trhbrt
AT THE BEGINNING OF EACH PLAY SEASON:
Tighten all hardware.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are
loose, cracked, or missing.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or
other deterioration. Replace as needed.
Check metal parts for rust. If found, sand and repaint using a nonlead-based paint meeting
the requirements of 16 CFR 1303.
Check all wood members for deterioration and splinters. Sand down splinters and replace
deteriorating wood members.
Reinstall any plastic parts, such as swing seats or any other items that were removed for the
cold season.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
TWICE A MONTH DURING PLAY SEASON:
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are
loose, cracked, or missing.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
ONCE A MONTH DURING PLAY SEASON:
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or
other deterioration. Replace as needed.
At the end of each play season or when the temperature drops below 32°F (temperature
to be selected by the manufacturer).
Remove plastic swing seats and other items as specified by the manufacturer and take
indoors or do not use.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
Owners shall be responsible for maintaining the legibility of the warning labels.
When conducting inspections, it is recommended that you use the Outdoor Home
Playground Safety Checklist published by the US Consumer Product Safety
Commission, a copy of which is contained in this user manual.
IMPORTANT WARNINGS AND INSTRUCTIONS

8
Trhbrt
The Consumer Product Safety Commission estimates there are about 200,000 playground related injuries
involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all
playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under
and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self
evident that a fall onto a shock absorbing surface is less likely to cause a serious injury than a fall onto a hard
surface. Playground equipment should never be placed on hard surfaces such as concrete or asphalt and while
grass may appear to be acceptable it may quickly turn to hard packed earth in areas of high traffic. Shredded bark,
mulch, wood chips, fine sand or fine gravel are considered to be acceptable shock absorbing surface when
installed and maintained at a sufficient depth under and around playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a life-threatening
head injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of
6” (15.25CM), 9” (22.9CM), and 12” (30.5CM).
FALL HEIGHT IN FEET FROM WHICH
A LIFE THREATENING HEAD INJURY WOULD NOT BE EXPECTED
TYPE OF MATERIAL 6”(15.25CM)
DEPTH 9”(22.9CM) DEPTH 12”(30.5CM) DEPTH
Double shredded bark mulch 6”(15.25CM) 10”(25.4CM) 11”(27.94CM)
Wood Chips 6”(15.25CM) 7”(17.8CM) 12”(30.5CM)
Fine Sand 5”(12.7CM) 5”(12.7CM) 9”(22.86CM)
Fine Gravel 6”(15.25CM) 7”(17.8CM) 10”(25.4CM)
However, it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing
material is used. We recommend that a shock absorbing material should extend a minimum of 6ft in all directions
from the perimeter of stationary equipment such as climbers and slides. However, because children may
deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing
a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the
supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various materials.
No particular material is recommended over another. However, each material is only effective when
Properly maintained. Materials should be checked periodically and replenished to maintain correct depth as
determined necessary for your equipment. The choice of a material depends on the type and height of the
playground equipment, the availability of the material in your area and its cost.
Note: The maximum fall height for this product is 6 feet. The minimum ground Clearance between the bottom of the
suspended plays and the playing or ground service must be 8 inches.

This information has been extracted from the CPSC publication on" Playground Safety". You can obtain
more information by sending a postcard to the: Office of public Affairs，U.S. Consumer Product Safety
Commission，Washington，D.C.20207
IMPORTANT CONSUMER INFORMATION SHEET

9
Trhbrt
The following guidelines are extracts from the Consumer Product Safety Commission Outdoor
Home Playground Safety Handbook. It is recommended that you read the entire handbook and
take necessary precautions to prevent serious injuries to your children, including:
CHOOSING A SITE
When you choose a home playground, a location away from roads and driveways and readily visible
from inside the home and patios or porches, is important.
Create a site free of obstacles that could cause injuries such as low overhanging tree branches,
overhead wires, tree stumps and/or roots, large rocks, bricks and concrete.
Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over
and loose-fill surfacing materials washing away during heavy rains. Some sites may need regrading
to improve drainage or to reduce the slope.
Locate play set at least 6 feet from any structure or obstacles, such as a house, fence, sheds, trees
or poles. Swings should be further away from structures to the front and rear of the swings-a
distance equal to twice the height of the top bar from which the swing is suspended.
Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious
burns. Aslide that faces north will receive the least direct sunlight.
SELECT PROTECTIVE SURFACING
One of the most important things you can do to reduce the likelihood of serious head injuries is to install
shock-absorbing protective surfacing under and around your play set. The protective surfacing should be
applied to a depth that is suitable for the equipment height in accordance with ASTM F1292. There are
different types of surfacing to choose from; whichever product you select, follow these guidelines:
Do not install home playground equipment over concrete, asphalt, or any other hard surface. A
fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not
considered protective surfacing because wear and environmental factors can reduce their shock
absorbing effectiveness. Carpeting and thin mats are generally not adequate protective
surfacing.
Loose-Fill Materials
Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered
wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches
of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will
compress to about a 9-inch depth of surfacing over time. The surfacing will also compact, displace,
and settle, and should be periodically refilled to maintain at least a 9-inch depth.
Use containment, such as digging out around the perimeter and/or lining the perimeter with
landscape edging. Don’t forget to account for water drainage.
Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of
loose-fill materials, mark the correct level on play equipment support posts. That way you can easily
see when to replenish and/or redistribute the surfacing.
Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
IMPORTANT CONSUMER INFORMATION SHEET

10
Trhbrt
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials-like rubber tiles or
poured-in-place surfaces.
Installations of these surfaces generally require a professional and are not “do-it-yourself” projects
Review surface specifications before purchasing this type of surfacing. Ask the installer /
manufacturer for a report showing that the product has been tested to the following safety standard:
ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use
Zone of Playground Equipment. This report should show the specific height for which the surface is
intended to protect against serious head injury. This height should be equal to or greater than the fall
height-vertical distance between a designated play surface (elevated surface for standing, sitting, or
climbing) and the protective surfacing below-of your play equipment.
Check the protective surfacing frequently for wear.
PLACEMENT
Proper placement and maintenance of protective surfacing is essential. Be sure to:
Extend surfacing at least 6 feet from the equipment in all directions.
For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to
twice the height of the top bar from which the swing is suspended.
IMPORTANT CONSUMER INFORMATION SHEET

11
Trhbrt
Outdoor Home Playground Safety Checklist
Use this to help make your home playground a safe place to play!
Supervision Be sure to always supervise children on play equipment.
Surfacing
Install a protective surface under and around play equipment to reduce the
likelihood of serious head injuries.
For most play equipment, install protective surfacing 6 feet in all directions
beyond the equipment.
For swings, extend protective surfacing in front and back of the swing to a
distance that is twice the height of the bar from which the swing is suspended.
For tire swings, install protective surfacing outward from the swing equal to the
suspension
chain plus 6 feet.
Types of
Surfacing
Carpeting and thin mats are not adequate as protective surfacing. Maintain at
least 9 inches of loose-fill material (see page6) or use anASTM F1292 rated
material at the depth required for the equipment height.
Use wood mulch/chips, shredded rubber mulch, or engineered wood fiber for
equipment up to 8 feet high.
Use sand, pea gravel, or mulch products listed above for play equipment up to
5 feet high; or
Use surface mats tested to provide impact protection equal to or greater than
the height of the play equipment.
Equipment
Maintenance
Periodically check nuts, bolts, caps, swing seats, suspension ropes, chains,
and cables and replace as necessary. Maintain loose-fill surfacing and surface
mats.
Opening
Eliminate openings that can trap a child's head or neck, such as openings in
guardrails or ladders. Openings should be smaller than 3 1/2 inches to prevent
entry of a small child's body, or larger than 9 inches to allow a child's head and
body to slide completely through.
Ropes Never attach jump ropes, clotheslines, pet leashes, or cords of any kind to play equipment.Anchor any climbing ropes at both ends. Remove drawstrings from
children's clothes. Children can strangle on these.
Anchors Bury or cover anchors with adequate surfacing material to prevent tripping.
Play equipment should not tip over.
Guardrails
or
Barriers
Make sure that platforms and ramps over 30 inches high have guardrails and
barriers to prevent falls.
Repair Repair sharp points and edges on equipment that can cause injuries.
Upkeep of
Hardware Replace missing hardware, eliminate protruding bolts, and close "S" hooks that can cause injuries.
IMPORTANT CONSUMER INFORMATION SHEET

12
Trhbrt
What to Inspect:
Hardware:
Inspect all nuts and bolts and tighten if required. Hardware should be firmly against, but not crushing the
wood. Over-tightening hardware crushes wood fibers and can split wooden components resulting in the
bolt thread extending beyond the wood. This poses a severe safety hazard. If bolt threads protrude
beyond the wood surface, replace the bolt with a shorter one that will not protrude. If splintering has
occurred from over-tightening, larger washers can be purchased at your local hardware store and
installed under the bolt head. Be sure to reuse or replace your lock washers.
Major Wooden Parts:
Inspect for structural defects and splintering. If necessary, lightly sand and refinish with an exterior water
repellent stain. Seasonal checking or cracking of the grain on wooden parts is quite natural water and
heat are the most frequent causes of expansion and contraction of wood fibers. Our wood set has been
treated with stain to resist weathering. But it needs to be maintained periodically by applying new stain or
paint.
Dowels (Rungs)
Inspect for structural defects and splintering. If necessary, lightly sand and refinish with a clear water
repellent, exterior sealant or boiled linseed oil. Do NOT paint, varnish or finish rungs with any substance
that may reduce your child’s ability to firmly grasp or step on the rungs.
Swing hangers
Inspect for correct installation. Assure the bend of the swing hanger is positioned tightly against the stop
washer and the ladder or swing beam. The axis of the swing hanger bushing must be perpendicular to
the swing motion. Spray the nylon bushings with a household lubricant such as WD-40, if you hear
squeaking.
Plastic Swing Seats
Check for evidence of deterioration. Replace any swing seat that has developed cracks in the seat or has
exposed metal in the edges of the swing seat. If there are already exposed metal inserts on the edge of
the seat, remove the seats and chains to prevent serious injury. Remove plastic swing seats and take
indoors or do NOT use when the temperature drops below 32 degrees F.
Ropes, Cables and Chains
Check for evidence of deterioration. Ropes, cables and chains should be removed and replaced if
excessive wear is found. Contact our service center for replacement parts.
Metallic Components
Check for rusted areas on components such as monkey bars, hand supports, brackets, etc. Sand and
repaint using a non lead-based paint that meets the requirements of Title 16 CRF part 1303.
Play Area
Inspect to assure that the swing set has settled properly and the location of the set is still level.
IMPORTANT CONSUMER INFORMATION SHEET

13
Trhbrt
SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT
FOR YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY
Dimensions:
Product Dimension: 153.31’’ x 124.92’’
General Information:
The play set has been designed and engineered
for up to 6 children.
Maximum of 100 lb. (45kg) per child Combined
weight is not to exceed 700 pounds (315 kg).
RECOMMENDED PLAY AREA DIAGRAM
GROUND COVER INFORMATION
6FT
6FT
PLAYSET
6FT
6FT

14
Trhbrt
FRONTVIEWOFCOMPLETEPRODUCT
BACK VIEW OF COMPLETE PRODUCT
COMPLETE PRODUCT VIEW

15
Trhbrt
These are the tools that are generally required for installation.
These tools are not included in the purchased packaging unless stated below.
Electric Drill Phillips Head Screw Driver
Phillips Head Screwdriver Tape Measure
Ladder or Step Tool
Working Gloves
INCLUDED
TOOLS NEEDED
e
(#6)
(#5)
e

16
WOOD PARTS LIST

17
WOOD PARTS LIST

18
NOTE: EXTRA HARDWARE MAY BE INCLUDED
Measuring Hardware
It is very important that you get the right hardware in the correct place when assembling the unit. You can
usearuler to measure your hardware or you can compare the hardware to the hardware identification
page.
NOTES:
1) Do not include bolt head when measuring length of bolt.
2) Include full length of deck screw when measuring
HARDWARE PARTS LIST
S14-3PCS
3/16X18MM
S5-54PCS
M4X28MM
S6-84PCS
M4X35MM
S7-4PCS
M4X45MM
B1-18PC
5/16X28MM
B2-6PCS
5/16X38MM
B3-24PCS
5/16X50MM
B4-14PCS
5/16X60MM
B9-2PCS
5/16X110MM
V9-64PCS
5/16
V4-6PCS
5/16
V6-8PCS
5/16
V3-4PCS
5/16
V7-4PCSV31-12PCS
1/4
V1-12PCS
5/16
V24-16PCS
3/8
V2-20PCS
1/4
V8-56PCS
5/16
V20-65PCS
1/4
B28-12PCS
1/4X22MM
S3-37PCS
1/4X50MM
S2-22PCS
1/4X40MM
S1-6PCS
1/4X30MM
S18-4PCS
ST7X50MM
S15-6PCS
1/4X80MM

19
Trhbrt
U2X2pcs
U4X5pcs
U13X2pcs
U9X1pc
cp1XB275Ucp1XS275U
U5X2pcs
U1X1pc U10X1pc
U42X2pcs U8X1pc U11X2pcs
U3X2pcs U50X4pcs U32X3pcs
COMPONENT PARTS LIST