SPORTSPOWER MSC-3878 User manual

INTRODUCTION
Dear Valued Customer,
Congratulations on your Sportspower play set purchase! Please read and completely understand the
contents of this owner’s manual. This manual contains specific instructions and warnings that must be followed
to prevent injuries.
This play set is for residential use only. This play set is NOT intended for public or commercial use. The
warranty will be voided if the play set is used in a commercial application.
The product is designed for children between the ages of 3-8. Children must NOT play on this set until it is
properly assembled and inspected by an adult. Adult supervision is required at all times while children are
playing on the equipment. Do not allow children under six (6) years old to be near during the assembly of this
product due to choking hazards of small parts.
The equipment must be installed on level ground. Uneven ground must be leveled prior to installation.
Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and
unstable which may result in serious injuries. You must ensure there are no obstructions or structures (e.g.
electrical wires, branches, house, fence, garage, etc) within six (6) feet from the equipment.
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend to
install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber
(for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock
absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground equipment,
do not adequately protect children from serious head injuries. Install protective surfacing at least six feet in all
directions from play equipment. For swings, the surface should extend, in back and front, twice the height of the
suspending bar. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick
floor. Please refer to extracts from the CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK contained in this manual for further details.
Do not allow children to use the product during windy or wet weather conditions. It is highly recommended
the product be anchored into the ground to prevent movement and to make the swing set more stable during use.
You should consult a local contractor about ways to anchor the product in your location.
The equipment must be checked before each use and maintained regularly. This includes, but is not limited
to inspecting the play set for cracks, excess wear, missing parts, loose connections and for overall integrity.
When the equipment shows any signs of weakness or damage, you must stop using the play set immediately,
properly store the set or restrict access by users until the condition is resolved.
Your product is warranted against defects in material and workmanship. Extended warranty is also
offered to those customers registering their products at www.sportspowerltd.net within 14 days from the
date of purchase. Please refer to our warranty policy at the back of this manual for details.
If you experience any problems with your product, do not return to the store. For customer service,
please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time. If you are unable to reach us at
this number for any reason, please visit www.sportspowerltd.net.

1
IMPORTANT INSTRUCTIONS AND WARNINGS
WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT
AGE LIMIT
This product is designed to be used by up to eight (8) children between the ages of 3 to 8. Maximum user
weight is 100 pounds (45.4kg) each with a combined maximum weight of 800 pounds (363kg).
The play set is designed for children over three (3) years of age. Use by smaller children can result in
entrapment.
On-site adult supervision is required at all times for children of all ages.
Do not allow use by children with any physical condition that may affect his/her ability to use this equipment
safely.
BEFORE YOU BEGIN
Carefully read all instructions in this manual before assembling and using this product.
The unit must be assembled by adults. Heavy duty working gloves must be worn to avoid injuries during
assembly.
Children must not use the equipment until it is properly assembled and anchored.
Adult supervision is required during the use of this equipment at all times.
Unpack all parts. Take a complete inventory of all parts and hardware using the parts and hardware lists in
the following pages. If any parts are missing, do not return to the store. Please call customer service toll-free
number listed on the cover page for assistance. Store the product back in the original box and do not begin to
install until all parts are obtained.
LOCATION OF PLAY SET
The equipment must be placed more than six(6) feet(1.8 meter) from any structures or obstructions,
including but not limited to buildings, fence, garage, trees, laundry lines, electrical wires. Children can be
seriously injured running or swinging into obstacles.
The play set must be installed on level ground. Uneven ground must be leveled prior to installation.
Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and
unstable which may result in serious injuries.
Remove any tripping hazards from the safe play area, such as roots, tree stumps, rocks, landscaping,
sprinkler heads, railroad ties, plumbing and electrical connections.

2
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor.
A fall onto a hard surface can result in serious injury or death to the user. The following is a list of
recommended ground covers from the Consumer Product Safety Commission:
SUGGESTED MATERIAL
DO NOT use this equipment if the swing seat, slide or any parts are wet. Use the play set only when the
parts are clean and dry. If the equipment is wet, the user could slip and suffer injuries.
UNCOMPRESSED DEPTH
Double Shredded Bark Mulch 9”
Uniform Wood Chips 12”
Fine Gravel 12”
Fine Sand 12”
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend to
install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded
rubber (for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as
shock absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground
equipment, do not adequately protect children from serious head injuries. Install protective surfacing at
least six feet in all directions from play equipment. For swings, the surface should extend, in back and front,
twice the height of the suspending bar. You should consult a local contractor about ways to secure the
product in your location. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth,
tile or brick floor. Please refer to the CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR
HOME PLAYGROUND SAFETY HANDBOOK for detailed guidelines to prevent injuries from falls and other
hazards on public and home playgrounds.
WARNINGS ON ANCHORING
It is highly recommended the product be anchored into the ground to prevent movement and to make the swing
set more stable during use.
Some consumers want an anchoring system that allows the product to be moved to different locations. Other
consumers want to keep their swing set in a permanent location.
There are different types and different methods of anchoring this product. Sportspower does not make a specific
anchoring recommendation as each consumer’s need and conditions can vary.
It is highly recommended that you seek the opinion from a local licensed contractor on the best way to secure the
swing set in your location. The best way to anchor a product is to create a concrete footing and use that as a
base for an anchor. Whatever method you prefer for your location, an anchoring system for this product should be
used at all times.
WEATHER CONDITIONS
Please be aware of weather conditions when using the equipment. If it is too windy, users could lose control
and suffer injuries. The playground equipment must be properly anchored, stored away or restricted from
use during inclement weather such as heavy winds or severe weather storms. You should consult a local
contractor about ways to anchor the product in your location.
PLAY SUPERVISION
DO NOT allow more than one child to play on the individual swing, trampoline or slide component at any one
time. The maximum user limit for the flying saucer and glide ride is two persons.
DO NOT allow children to stand on the slide, swing seats or glide ride.
DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being
struck by other children while playing on swings, slides, trampolines etc.

3
DO NOT allow children to twist the swing chains or ropes, or loop them over the top support bar as this may
reduce the strength of the chain or rope.
DO NOT swing empty seats as this may cause injuries.
ALWAYS guide children to sit in the center of swinging parts, with their full weight placed in the seat center
and holding on to the swing chains.
DO NOT allow children to jump off the equipment while it is in motion. ALWAYS come to a full stop before
dismounting.
ALWAYS dress children appropriately for proper play, e.g. wear well-fitted rubber sole shoes, and remove
loose or sharp items such as jewelry, hair accessories, scarves which may become entangled in the
equipment or cause injuries.
ALWAYS make sure children remove their bike or other sports helmets before playing on the playground.
DO NOT allow children to slide down head first.
DO NOT allow children to climb onto swing or jump to/from different play areas of the equipment.
ALWAYS return safely to the ground before approaching another play area.
DO NOT allow children to climb on structural parts (e.g. legs, top bar). These are structural components
and are not designed for play.
ALWAYS check the slide or other parts exposed to the body for extreme heat from the sun before allowing
children to use the equipment.
ALWAYS prevent access and secure from any unauthorized use when there is no adult supervision.
DO NOT allow pets or other animals near the equipment to prevent damage or injuries.
Adequate overhead clearance is essential.Aminimum of 24 ft (7.3 meters) from ground level is
recommended. Provide clearance for wires, tree limbs, and other possible hazards.
Use the trampoline in a well-lit area.Artificial illumination may be required for shady areas.
TRAMPOLINE WARNINGS
Do not allow more than one person on the trampoline at a time. Multiple users can cause loss of control,
collision or falls that could result in serious injury.
Jumpers should remove their shoes and wear either socks or be barefoot when using the trampoline.
Do not jump onto the trampoline. Carefully step on and off the trampoline mat. Do not use the trampoline as
a springboard to other objects. Do not jump to or from the trampoline to the flying saucer or any other
component of the swing set.
Avoid bouncing too high. Maintain control of the bounce and focus on landing in the center of the
trampoline.
Bounce only when the surface of the mat is dry. Do not use during wet or windy conditions.
Never use the trampoline without the frame padding properly secured and fully covering the frame.
Remove any obstructions from beneath the trampoline before each use.
Do not allow any pets onto the trampoline as the mat may be damaged.
Any type of sharp or pointed objects must be kept off the trampoline mat at all times.
Always inspect the trampoline before each use and replace any worn, defective or missing parts. Please
make sure to check following conditions that could represent potential hazards before using:
- Missing, improperly positioned, damaged or insecurely attached frame padding.
- Punctures, frays, tears or holes worn in the bed or frame padding.
- Deterioration in the stitching or fabric of the bed or frame padding.
- Broken, missing or damaged springs.
- A bent or broken frame.

4
- A sagging, broken bed.
- Sharp protrusions on the frame or suspension system.
- Protrusions of any types (especially sharp typed) on the frame, springs or mat.
- Loose stitching or any kind of deterioration of the mat.
If any of the above conditions exist, restrict use until proper repairs or replacements are made.
Do NOT attempt or allow somersaults. Landing on the head and neck can cause serious injury, paralysis,
or death, even when landing in the middle of the mat.
Use trampoline only with mature, knowledgeable supervision.
Step on and off the trampoline. It is a dangerous practice to jump from the trampoline to the floor or
ground when dismounting, or to jump onto the trampoline when mounting.
Stop bounce by flexing knees as feet come in contact with the mat. Learn this skill before attempting others.
Learn fundamental bounces and body positions thoroughly before trying more advanced skills. A
variety of trampoline activities can be carried out by performing the basic fundamentals in various
series and combinations, performing one fundamental after another, with or without feet bounces
between them.
Control is more important than height.
While keeping the head erect, focus eyes on the trampoline toward the perimeter. This will help
control bounce.
Avoid bouncing when tired. Keep turns short.
Properly secure the trampoline when not in use. Protect it against unauthorized use. Keep objects
away which could interfere with the performer. Maintain a clear area around the trampoline.
Responsibilities of the user
The key here is to stay in control of your jumps. DO NOT move onto more complicated, more difficult maneuvers
until you have mastered the basic, fundamental bounce. Read, understand, and practice all precautions and
warnings prior to using the trampoline. A controlled jump is when you land and take off from the same location.
For additional tips and instructions, contact a certified trampoline instructor.
Supervisor’s or owner’s role in preventing injuries
It is the responsibility of the supervisor(s) of the trampoline users to provide knowledgeable and mature
supervision. They need to know and enforce all the rules and warnings set forth in this manual in order to
minimize the likelihood of accidents and injuries and to inform users of these rules. During the periods of time
when supervision is unavailable or inadequate, the trampoline should be disassembled and stored in a secure
place to prevent unauthorized use. The supervisor is also responsible to ensure that the safety placard is placed
on the trampoline and that the jumpers are informed of these warnings and instructions.

5
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION
DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the
equipment and all parts are well secured and stable before each use.
ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous
to users.
DO NOT attach items to the equipment that are not specifically designed for use with the equipment,
including, but not limited to, jump ropes, clothesline, pet leashes, cables and chains as they may cause
choke hazards.
The steel and plastic parts used in your product are subject to normal wear. Gradual deterioration of the
material will occur, the speed of which will depend on the level of exposure to UV rays, airborne pollution,
outdoor weather conditions such as rain and wind and the amount of use. You must inspect the equipment
prior to every use. This includes, but is not limited to inspecting the set for cracks, excess wear, missing
parts, loose connections, and for overall integrity. When the set shows any signs of weakness, you must
stop using the play set immediately, properly store the set or restrict access by users until the condition is
resolved.
Verify that the suspended climbing ropes, chain or cable are secured at both ends and tightened, so that
there is no loose ropes, chain or cable hanging that can result in choking hazard.
When conducting inspections, it is recommended that you use the Suggested General Maintenance
Checklist and R outine Inspection and Maintenance Issues checklis ts provided by the US Consumer
Product S afety Commis s ion, a copy of which is contained in this us er manual.
CARE & MAINTENANCE INSTRUCTIONS
Inspect all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It is
particularly important that this procedure is followed at the beginning of each season.
Oil all metallic moving parts monthly during the usage period.
Sand rusted areas on metal tubing and repaint using a nonlead-based paint meeting the requirements of
Title 16 CFR Part 1303.
Check swing seats, ropes, cables and chains monthly during usage season for deterioration. Replacements
should be made in accordance with the manufacturer’s instructions.
Check all coverings for bolts and sharp edges twice monthly during usage season to be certain that they are
in place and replace when necessary. It is especially important to do this at the beginning of each new
season.
Do not use when the temperature drops below 32 degrees F (0 degrees C); remove and store the plastic
swing seats and slides indoors.

6
IMPORTANT
CONSUMER INFORMATION SHEET
The Consumer Product Safety Commission estimates there are more than 200,000 playground related injuries
involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all
playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under
and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self
evident that a fall onto a shock absorbing surface is less likely to cause a serious injury than a fall onto a hard surface.
Playground equipment should never be placed on hard surfaces such as concrete or asphalt and while grass may
appear to be acceptable it may quickly turn to hard packed earth in areas of high traffic. Shredded bark, mulch,,wood
chips, fine sand or fine gravel are considered to be acceptable shock absorbing surface when installed and maintained
at a sufficient depth under and around playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a life-threatening head injury
in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6” (15.25CM), 9”
(22.9CM), and 12” (30.5CM).
However,it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing material is
used.
We recommend that a shock absorbing material should extend a minimum of 6ft in all directions from the perimeter of
stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving
swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the
height of the pivot point measured from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No
particular material is recommended over another. However, each material is only effective when Properly maintained.
Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your
equipment. The choice of a material depends on the type and height of the playground equipment, the availability of
the material in your area and its cost.
Note: The maximum fall height for this product is 6 feet. The minimum ground Clearance between the bottom of the
suspended plays and the playing or ground service must be 8 inches.
This information has been extracted from the CPSC publication on" Playground Safety". You can obtain more information by sending a postcard to
the: Office of public Affairs，U.S. Consumer Product Safety Commission，Washington，D.C.20207
8”

7
ANCHORING
(NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY)
There are different ways of anchoring the equipment, depending on the type of ground on which
the equipment is to be installed. Make sure that all anchors are below ground level to prevent
tripping.
You should consult your local contractor to decide the most appropriate way to anchor the
equipment in your location.
The following anchoring options may be considered:
If your soil is hard (clay, etc.), the corkscrew method may be suitable.
Corkscrew Anchoring (Corkscrew Anchors not included)
Be sure that the swing set is located on level ground.
Twist the corkscrew anchor into the ground until only the end with the hook is above the ground
and next to the leg. Insert the hook into the bottom opening of the leg.
Ensure that the hook is secured onto the leg opening.
Concrete Anchoring (Materials not included)
●If the swing set is set up on grounds with sandy soil (soft) condition, it must be
anchored with concrete footing (concrete not included)
●Be sure that the swing set is assembled and placed on level ground
●Dig holes around swing leg tube, as shown in drawing in the next page. As you dig
deeper, enlarge the diameter of the hole to fix the cement
●Place 2 inches of brick or gravel underneath the leg, as shown in drawing in the next
page
●Use about 45 lbs. of concrete per leg
●Cover the concrete with dirt and protective surface material
●Allow 6-7 days for the concrete to dry properly

8
Note: The maximum fall height for this product is 6 feet. The minimum ground
clearance between the bottom of the suspended plays and the playing
or ground surface must be 8 inches.
You must maintain a minimum of 8 inches of ground clearance.
WARNING
Please properly anchor the swing set to minimize the risk of injury or death.
If the swing set is used without proper anchoring, it may be dangerous and
may tilt over.
8”
FRAME LEG
CONCRETE
BRICK OR GRAVEL BED
2”
12-5/8”
5”

9
CARE AND MAINTENANCE CHECKLIST
Tighten all hardware.
AT THE BEGINNING OF EACH PLAYSEASON:
Lubricate all metallic moving parts permanufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
Check allmoving parts including swing seats, ropes, cables and chains forwear, rust or other
deterioration. Replace as needed.
Checkmetal parts for rust. If found, sand and repaint using a non-lead paint meeting the
requirements of 16 CFR 1303.
Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold
season.
Rake and check depth of loose fillprotective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace asneeded.
TWICE A MONTH DURING PLAY SEASON:
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges and corners. Replace if they are loose,
cracked or missing.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace asneeded.
ONCE A MONTH DURING PLAY SEASON:
Lubricate all metallic moving parts per manufacturer’s instructions.
Check allmoving parts including swing seats, ropes, cables and chains for wear, rust or other
deterioration. Replace as needed.
Rake and check depth of loose fillprotective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace asneeded.
At the end of each playseason or when the temperature drops below32 degreesF (0 degrees C).
AT THE END OF EACH PLAY SEASON:
Remove plastic swing seatsand other items as specified by the manufacturer and take indoors or
do not use.
Rake and check depth of loose fill protective surfacing materials to preventcompaction and to
maintain appropriate depth. Replace asneeded.
As a general rule, maintenance should be performed at any time it is deemed necessary.
Please use care when disassembling the equipment, when it is no longer in operational condition.
Wear heavy duty working gloves to avoid injuries.
DISPOSAL INSTRUCTIONS
Fully disassemble the entire swing and slide sets before disposal. Do not leave partially
disassembled parts in areas accessible by children.
Should you wish to recycle the steel tubing, please take the frame to your local recycling center.
All plastic parts can be recycled, take it to your local recycling center. Do not let children playwith
any disassembled parts meant for disposal, such as chains, slide, tubing, bolts, nuts, screws, etc.
All rusted parts, bolts must be properly disposed of in trash bin. Do not reuse.
Owners shall be responsiblefor maintaining thelegibility of the warning labels.

11
Parts for swing set frame
A1 CORNER TOP BAR 2
A2 MIDDLE TOP BAR 1
A3 TOP BAR 1
A4 TOP BAR 1
A5 LEG WITH FOAM 2
A6 LEG (WITH THREE HOLES) 4
A7 CROSS BAR (WITH TWO HOLES) 1
A8 CROSS BAR (WITH FOUR HOLES) 1
Hardware for swing set frame
B1 BOLT 5/16”*2.5” (8MM*63MM) 14
B2 BOLT 5/16”*2.5” (8MM*68MM) 4
B3
NYLON NUT 5/16’’ 18
B4
PLASTIC CAP (WITH ARC WASHER) 18
B5
5/16’’ARC WASHER 14
B6
5/16’’ WASHER 4

12
Parts for flying saucer
R1
PVC COVERED CHAIN
(PRE-ASSEMBLED)
4
R2A
LONG EYE BOLT WITH CHAIN
( PRE-ASSEMBLED)
4
R2B
SHORT EYE BOLT WITH CHAIN
( PRE-ASSEMBLED)
4
R3 BRACKET 2
R4
FLYING SAUCER TUBE 4
R7
FLYING SAUCER 1
R8 BRACKET CLAMP 2
Hardware for flying saucer
F1-1 BOLT 3/8”*3.3” (9.5MM*85MM) 4
F2
REINFORCING STEEL SPACER 8
F3
NYLON NUT 3/8’’ 12
F4
3/8” ARC WASHER 4

13
Parts for trampoline
T1
PROTECTIVE NET 1
T2 JUMP MAT 1
T3
FRAME PAD 1
T4A-N L-SHAPED TUBE (LEFT) 1
T4B-N L-SHAPED TUBE (RIGHT) 1
T5-N
STRAIGHT TUBE 1
T6-N
HANDLE BAR WITH FOAM 1
T7A-N HANDLE BAR BASE TUBE(LEFT) 1
T7B-N HANDLE BAR BASE TUBE(RIGHT) 1
T8
SUPPORTING TUBE 1
T9 SPRINGS 28
Hardware for trampoline
T10 BOLT 5/16”*63MM 2
T11 BOLT 5/16”*40MM 2
T12
ARC WASHER 5/16” 4
T13
CAP NUT 1/4” 4
T14
NYLON NUT 5/16’’ 4
T15 BOLT 1/4”*42MM 2
T16 BOLT 1/4”*35MM 2
T17
SCREW M5*16MM 2
T18 SPRING WASHER (MEDIUM) 4
T19
ARC WASHER 1/4” 8
T20 SPRING WASHER (SMALL) 2

14
Bracket for glide ride
L3
BRACKET 1
L4
BRACKET CLAMP 1
L5
REINFORCING STEEL SPACER 2
N3R
BOLT 5/16”*1” (8MM*25MM) 2
N7
NYLON NUT 5/16’’ 2
Parts for glide ride
L1-N TOP SECTION HANGER 2
L2-N GLIDE SEAT SUPPORT 2
M1 TUBE CAP(PRE-ASSEMBLED) 2
M2
SMALL NYLON BEARING
(PRE-ASSEMBLED)
2
M3
LARGE NYLON BEARING
(PRE-ASSEMBLED)
4
M4 GLIDE SEAT 2
M5 FOOTREST 2

15
Hardware for glide ride
N1 BOLT 1/4”*1.5” (6.5MM*37MM) 4
N2R BOLT 1/4’’*1.7” (6.5MM*43MM) 2
N4 SCREW 0.22”*3/4” (5.5MM*19MM) 4
N5 J-BOLT 2
N6 SPRING WASHER (MEDIUM) 4
N8 CAP BOLT 1/4”*5/10” (6.5MM*14MM) 2
N9 CAP NUT 1/4” 4
N10 NUT 1/4” 2
N11 SPRING WASHER (LARGE) 2
N12 SPRING WASHER (MEDIUM) 4
Parts for swing seat
J1 PVC COVERED CHAIN
(PRE-ASSEMBLED) 4
J3
EYE BOLT WITH
ATTACHMENT BOLT
(PRE-ASSEMBLED)
8
K1 SWING SEAT 2
Hardware for swing seat
J6 NYLON NUT 5/16’’ 8
J7 5/16’’ WASHER 4
J8 PLASTIC CAP (WITH ARC WASHER) 4
J9 PLASTIC CAP (WITH LARGE WASHER) 4

16
Parts for slide
H1 RIGHT PLASTIC PANEL 1
H2 LEFT PLASTIC PANEL 1
H3 PLASTIC SHEET 1
H4 H3 CONNECTING PLATE 1
H5 BACK SUPPORT PANEL 2
H6 CONNECTING PLATE 4
H7 UPPER CONNECTING PLATE 1
X1-N METAL LEG 2
X2-N LEFT SUPPORTER BAR 1
X3-N RIGHT SUPPORTER BAR 1
X4-N SUPPORTER BAR 1
X5 METAL BRACKET 2
X6 LADDER STEP 2
Hardware for slide
H10 BOLT 1/4”*13MM 10
H11 BOLT 1/4”*16MM 8
H12 BOLT 1/4”*38MM 2
H13 BOLT 1/4”*30MM 4
H14 BOLT 1/4”*36.5MM 8
H15 WASHER 24
H16 SPRING WASHER 20
H17 CAP NUT 1/4” 8
H18 BOLT 1/4”*20MM 2

17
Place the playground equipment on level ground and not less than
6ft (1.8m) from any structure or obstruction such as a fence, garage,
house, overhanging branches, laundry line, or electrical wires.
ASSEMBLY INSTRUCTIONS
Do not install the playground equipment over concrete, asphalt,
packed earth, or any other hard surface; a fall onto a hard surface
can result in serious injury or death to the equipment user.
Adequate overhead clearance is essential. A minimum clearance from
ground level shall be recommended. Provide clearance for wires, tree
limbs, and other possible hazards.
Use the equipment in a well-lit area. Artificial illumination may be required
for shady areas.
Secure the equipment against unauthorized and unsupervised use.
The owner and supervisors of the trampoline are responsible to make all
users aware of practices specified in the use instructions.
For ease of installation, do not over-tighten the nuts and bolts when
you are first putting the equipment together. This will allow room
for adjustments during installation.
TIGHTENING NUTS & BOLTS
Once you have finished assembling each component of the play set,
make sure to go back over each step and properly tighten all nuts,
bolts and plastic caps. Check the entire unit to ensure all parts are
properly assembled before allowing children to use the playground
equipment.

18
REFERENCE FOR AREA OF INSTALLATION
STEP 1 – Assemble top bar of swing set frame
Connect A1, A3, A2, A4 and A1 and secure with B1, B5, B4 and B3 as shown below.
Note: All round holes should be facing up and concave holes facing down.
IMPORTANT NOTE: A3 is not symmetrical. The end of A3 with the smaller section must be
attached to A1, on the outer side of the equipment.
A2
B3
B5
A1
B4
B1
B3
B1
B5
A1
Round holes
face up
Concave holes
face down
A3
A4
B4
B3
B4
B3
3
B4
B1
B5
B5
B1