SPORTSPOWER MSC-3990 Mounting instructions

DO NOT RETURN TO THE STORE.
For customer service, please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time
or visit our website at www.sportspowerltd.net
SPORTSPOWER LTD, FLAT M, 3/FLOOR, KAISER ESTATE PHASE 3, 11 HOK YUEN STREET, HUNGHOM, KOWLOON, HK.
Corporate US toll-free number 1-800-497-6106
8 STATION SWING SET
MODEL # MSC-3990
OWNER’S MANUAL
ASSEMBLY INSTRUCTION, CARE, MAINTENANCE AND USER’S GUIDE
FOR RESIDENTIAL USE ONLY
- This product is intended for use by children from ages 3 to 8
- This unit is designed for use by up to 8 children at one time.
Maximum weight of each user is 100 lbs.(45.4kg), with a
combined maximum weight of 800lbs(363kg)
- Assembly requires two adults
- Do not allow more than one child to play on the individual
swing/slide at the same time
- Do not allow children to slide down head first.
WARNING
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

Dear Valued Customer,
Congratulations on your Sportspower play set purchase! Please read and completely understand the contents
of this owner’s manual. This manual contains specific safety instructions that must be followed to enable safe
play and prevent injuries. This play set is for residential use only.
This play set is NOT intended for public or commercial use. The warranty will be voided if the play set is
used in a commercial application.
The product is designed for use by children between the ages of 3-8. Children must NOT play on this set until
it is properly assembled and inspected by an adult. Adult supervision is required at all times while children
are playing on the equipment. Do not allow children under six (6) years old to be near during the assembly
of this product due to choking hazards of small parts.
The equipment must be installed on level ground. Uneven ground must be leveled prior to installation.
Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and
unstable which may result in serious injuries. You must ensure there are no obstructions or structures (e.g.
electrical wires, branches, house, fence, garage, etc) within six (6) feet from the equipment.
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommends to
install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber
(for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock
absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground equipment,
do not adequately protect children from serious head injuries. Install protective surfacing at least six feet in
all directions from play equipment. For swings, the surface should extend, in back and front, twice the height
of the suspending bar. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile
or brick floor. Please refer to extracts from the CONSUMER PRODUCT SAFETY COMMISSION’S
OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK contained in this manual for further details.
Do not allow children to use the product during windy or wet weather conditions. You should consult a local
contractor about ways to anchor the product in your location.
Please thoroughly read and follow the instructions in this Owner’s Manual to ensure safe and enjoyable play
for your children. The equipment must be checked before each use and maintained regularly. This includes,
but is not limited to inspecting the play set for cracks, excess wear, missing parts, loose connections, and for
overall integrity. When the set shows any signs of weakness or damage, you must stop using the play set
immediately, properly store the set or restrict access by users until the condition is resolved.
Your product is warranted against defects in material and workmanship. Extended warranty is also offered
to those customers registering their products at www.sportspowerltd.net within 14 days from the date of
purchase. Please refer to our warranty policy at the back of this manual for details.
INTRODUCTION
1
If you experience any problems with your product, do not return to the store.
For customer service, please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time.
If you are unable to reach us at this number for any reason, call 1-800-497-6106 or visit
www.sportspowerltd.net

IMPORTANT SAFETY INSTRUCTIONS
BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and using this
product. The unit must be assembled by adults. Heavy duty working gloves must be worn to avoid injuries
during assembly.
Children must not use the equipment until properly assembled and anchored. Adult supervision is required
during the use of this equipment at all times
READ ALL INSTRUCTIONS BEFORE ASSEMBLYING OR USING THIS EQUIPMENT
AGE LIMIT
• This product is designed to be used safely by up to six (8) children between the ages of 3 to 8. Maximum
user weight is 100 pounds (45.4kg) each with a combined maximum weight of 800 pounds (363kg.)
•
The play set is designed for children over three (3) years of age. Use by smaller children can result in
entrapment.
• On-site adult supervision is required at all times for children of all ages.
•
Do not allow use by children with any physical condition that may affect his/her ability to use this equipment
safely.
BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and using this
product. The unit must be assembled by adults. Children must not use the equipment until it is properly
assembled and anchored. Adult supervision is required during the use of this equipment at all times.
• Identify the location appropriate for the placement of your equipment. The play set must be placed on level
ground and not over hard surface. Ensure equipment is placed more than six (6) feet from any structures
or obstructions on all sides. Remove any tripping hazards from the vicinity of the play area, such as roots,
stumps, rocks, landscaping, sprinkler heads, exposed plumbing, electrical boxes, etc.
•
Unpack all parts. Take a complete inventory of all parts and hardware using the parts and hardware lists in
the following pages. If any parts are missing, please call customer service for assistance. Store the product
back in the original box and do not begin to install until all parts are obtained.
LOCATION OF PLAY SET
•
The equipment must be placed more than six(6) feet(1.8 meter) from any structures or obstructions, including
but not limited to buildings, fence, garage, trees, laundry lines, electrical wires. The safe play area refers to
a zone extending 6 feet beyond the play set on all sides, including the space above the play set. Children
can be seriously injured running or swinging into obstacles. The play set must be installed on level ground.
Uneven ground must be leveled prior to installation. Installation on sloping or uneven ground will put stress
on the joints, causing the unit to become loose and unstable which may result in serious injuries.
•
Remove any tripping hazards from the safe play area, such as roots, tree stumps, rocks, landscaping, sprinkler
heads, railroad ties, plumbing and electrical connections.
• Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall
onto a hard surface can result in serious injury or death to the user
WARNING
2

3
The following is a list of recommended ground covers from the Consumer Product Safety Commission:
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommends to
install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber
(for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock
absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground equipment,
do not adequately protect children from serious head injuries. Install protective surfacing at least six feet in
all directions from play equipment. For swings, the surface should extend, in back and front, twice the height
of the suspending bar. You should consult a local contractor about ways to secure the product in your location.
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. Please
refer to the CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND
SAFETY HANDBOOK for detailed guidelines to prevent injuries from falls and other hazards on public and
home playgrounds.
WEATHER CONDITIONS
•
DO NOT use this equipment if the swing seat, slide or other parts are wet. Use the play set only when the
parts are clean and dry. If the equipment is wet, the user could slip and suffer injuries.
•
Please be aware of weather conditions when using the equipment. If it is too windy, users could lose control
and suffer injuries. The playground equipment must be properly anchored, stored away or restricted from
use during inclement weather such as heavy winds or severe weather storms. You should consult a local
contractor about ways to anchor the product in your location.
PLAY SUPERVISION
• DO NOT allow more than one child to play on the swing, trapeze bar or slide at any one time.
• DO NOT allow children to stand on the swing seats or glide ride.
•
DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being
struck by other children while playing on swings, slides, trapeze, etc.
•
DO NOT allow children to twist the swing chains or ropes, or loop them over the top support bar as this
may reduce the strength of the chain or rope.
• DO NOT swing empty seats as this may cause injuries.
•
ALWAYS guide children to sit in the center of swinging parts, with their full weight placed in the seat
center and holding on to the swing chains.
•
DO NOT allow children to jump off the equipment while it is in motion. ALWAYS come to a full stop
before dismounting.
•
ALWAYS dress children appropriately for safe play, e.g. wear well-fitted rubber sole shoes, and remove
loose or sharp items such as jewelry, hair accessories, scarf, ponchos which may become entangled in the
equipment or cause injuries.
•
ALWAYS make sure children remove their bike or other sports helmets before playing on the playground.
Helmets can become entrapped in playground, posing a strangulation hazard.
• DO NOT allow children to slide down head first.
• DO NOT allow children to climb onto swing or jump to and from different play areas of the equipment.
ALWAYS return safely to the ground before approaching another play area.
•
DO NOT allow children to climb on structural parts (e.g. legs, top bar). These are structural components
and are not designed for play.
•
ALWAYS check the slide or other parts exposed to the body for extreme heat from the sun before allowing
children to use the equipment.
• ALWAYS prevent access and secure from any unauthorized use when there is no adult supervision.
• DO NOT allow pets or other animals near the equipment to prevent damage or injuries.
SUGGESTED MATERIAL
Double Shredded Bark Mulch
Uniform Wood Chips
Fine Gravel
Fine Sand
SUGGESTED MATERIAL
9”
12”
12”
12”

REGULAR INSPECTION OF THE EQUIPMENT
•
DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the
equipment and all parts are well secured and stable before each use.
•
ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially
hazardous to users.
•
DO NOT attach items to the equipment that are not specifically designed for use with the equipment,
including, but not limited to, jump ropes, clothesline, pet leashes, cables and chains as they may cause
choke hazards.
•
The steel and plastic parts used in your product are subject to normal wear. Gradual deterioration of the
material will occur, the speed of which will depend on the level of exposure to UV rays, airborne
pollution, outdoor weather conditions such as rain and wind and the amount of use. You must inspect
the equipment prior to every use. This includes, but is not limited to inspecting the set for cracks, excess
wear, missing parts, loose connections, and for overall integrity. When the set shows any signs of
weakness, you must stop using the play set immediately, properly store the set or restrict access by
users until the condition is resolved.
•
Verify that the suspended climbing ropes, chain or cable are secured at both ends and tightened, so that
there is no loose ropes, chain or cable hanging that can result in choking hazard.
4

CARE AND MAINTENANCE
ANNUAL MAINTENANCE CHECKLIST
AT THE BEGINNING OF EACH PLAY SEASON:
• Tighten all hardware.
• Lubricate all metallic moving parts per manufacturer’s instructions.
•
Check all protective coverings on bolts, pipes, edges and corners. Replace if they are loose, cracked or
missing.
•
Check all moving parts including swing seats, ropes, cables and chains for wear, rust or other deterioration.
Replace as needed.
•
Check metal parts for rust. If found, sand and repaint using a non-lead based paint meeting the requirements
of 16 CFR 1303.
•
Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season.
• Rake and check depth of loose fill protective surfacing material to prevent compaction and to maintain
appropriate depth. Replace as needed.
TWICE A MONTH DURING PLAY SEASON:
• Tighten all hardware.
•
Check all protective coverings on bolts, pipes, edges and corners. Replace if they are loose, cracked or
missing.
•
Rake and check depth of loose fill protective surfacing material to prevent compaction and to maintain
appropriate depth. Replace as needed.
ONCE A MONTH DURING PLAY SEASON:
• Lubricate all metallic moving parts per manufacturer’s instructions
•
Check all moving parts including swing seats, ropes, cables and chains for wear, rust or other deterioration.
Replace as needed.
AT THE END OF EACH PLAY SEASON OR WHEN THE TEMPERATURER DROPS BELOW 32 °F .
• Remove plastic swing seats and other items as specified by the manufacturer and take indoors or restrict use.
• Rake and check depth of loose fill protective surfacing material to prevent compaction and to maintain
appropriate depth. Replace as needed.
As a general rule, maintenance should be performed at any time it is deemed necessary.
DISPOSAL INSTRUCTIONS
•
Please use care when disassembling the equipment. Wear heavy duty working gloves to avoid injuries.
• Fully disassemble the entire swing and slide sets before disposal. Do not leave partially disassembled
equipment parts in areas accessible by children.
• Should you wish to recycle the steel tubing, please take the frame to your recycling center.
•
All plastic parts could be recycled. Take it to your local recycling center. Do not let children play with
any disassembled parts destined for disposal, such as chains, slide, tubing, bolts, nuts, screws, etc.
5

IMPORTANT
CONSUMER INFORMATION SHEET
6
The Consumer Product Safety Commission estimates there are about 200,000 playground related injuries
involving children each year. Injuries involving this hazard pattern tend to be among the most serious of
all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The
surface under and around playground equipment can be a major factor in determining the injury-causing
potential of a fall. It is self evident that a fall onto a shock absorbing surface is less likely to cause a serious
injury than a fall onto a hard surface. Playground equipment should never be placed on hard surfaces such
as concrete or asphalt and while grass may appear to be acceptable it may quickly turn to hard packed earth
in areas of high traffic. Shredded bark, mulch,,wood chips, fine sand or fine gravel are considered to be
acceptable shock absorbing surface when installed and maintained at a sufficient depth under and around
playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a life-threatening
head injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at
depths of 6” (15.25CM), 9” (22.9CM), and 12” (30.5CM).
However,it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing
material is used.
We recommend that a shock absorbing material should extend a minimum of 6ft in all directions from the
perimeter of stationary equipment such as climbers and slides. However, because children may deliberately
jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing
a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the
pivot on the supporting structure. This information is intended to assist in comparing the relative shock
-absorbing properties of various materials. No particular material is recommended over another. However,
each material is only effective when Properly maintained. Materials should be checked periodically and
replenished to maintain correct depth as determined necessary for your equipment. The choice of a material
depends on the type and height of the playground equipment, the availability of the material in your area
and its cost. Note: The maximum fall height for this product is 6 feet. The minimum ground Clearance
between the bottom of the suspended plays and the playing or ground service must be 8 inches.
This information has been extracted from the CPSC publication on" Playground Safety". You can obtain
more information by sending a postcard to the: Office of public Affairs，U.S. Consumer Product Safety
Commission，Washington，D.C.20207
FALL HEGHT IN FEET FROM WHICH
A LIFE THREAENING HEAD INJURY WOULD NOT BE EXPECTED
TYPE OF MATERIAL 6” (15.25CM) DEPTH 9” (22.9CM) DEPTH 12” (30.5CM) DEPTH
11” (27.94CM)
12” (30.5CM)
9” (22.86CM)
10” (25.4CM)
10” (25.4CM)
7” (17.8CM)
5” (12.7CM)
7” (17.8CM)
6” (15.25CM)
6” (15.25CM)
6” (15.25CM)
5” (12.7CM)
WOOD CHIPS
FINE SAND
FINE GRAVEL
DOUBLE SHREDDED BARK MULCH
8”

TOOLS NEEDED
Please prepare the following tools
prior to assembling this equipment.
Special Socket Wrench Tape Measure
(Included) (Not included)
Hammer Wrench
(If you intend to install anchor, this is needed) (Included)
Wrench Big Allen Wrench
(Included) (Included)
Flat Head and Philips Head Screwdriver Middle Allen Wrench
(Not included) (Included)
Small Allen Wrench
Included)
7

Part list for main frame assembly
A1 LEFT TOP BAR 1PC
A2 MIDDLE TOP BAR 1PC
A3 RIGHT TOP BAR 1PC
A4 LEG 8PCS
A5 CROSS BAR (WITH TWO HOLES) 3PCS
A6 CROSS BAR (WITH FOUR HOLES) 1PC
C2 END CAP (PRE-ASSEMBLED) 2PCS
Hardware used for main frame assembly
B1 BOLT 5/16”*2.5”(8MM*64MM) 20PCS
B3 NYLON NUT 5/16’’ 20PCS
B4 PLASTIC CAP (WITH ARC WASHER) 20PCS
B5 5/16’’ ARC WASHER 12PCS
B6 5/16’’ WASHER 8PCS
Parts used for flying saucer assembly
R1 PVC COVERED CHAIN
(PRE-ASSEMBLED) 4PCS
R2A LONG EYE BOLT WITH CHAIN
( PRE-ASSEMBLED) 4PCS
R2B SHORT EYE BOLT WITH CHAIN
( PRE-ASSEMBLED) 4PCS
R3 BRACKET 2PCS
R4 FLYING SAUCER TUBE 4PCS
R7 FLYING SAUCER 1PC
R8 BRACKET CLAMP 2PCS
8

Hardware used for flying saucer assembly
Bracket used for glide ride assembly
L3 BRACKET 1PC
R8 BRACKET CLAMP 1PC
L5 REINFORCING STEEL SPACER 2PCS
N3R BOLT 5/16”*1”(8MM*25MM) 2PCS
N7 NYLON NUT 5/16’’ 2PCS
Part list for glide ride assembly
L1-N TOP SECTION HANGER 2PCS
L2-N GLIDE SEAT SUPPORT 2PCS
M1 TUBE CAP(PRE-ASSEMBLED) 2PCS
M2 SMALL NYLON BEARING
(PRE-ASSEMBLED) 2PCS
M3 LARGE NYLON BEARING
(PRE-ASSEMBLED) 4PCS
M4 GLIDE SEAT 2PCS
M5 FOOTREST 2PCS
F1-1 BOLT 3/8”*3.3”(9.5MM*85MM) 4PCS
F2 REINFORCING STEEL SPACER 8PCS
F3 NYLON NUT 3/8’’ 12PCS
F4 3/8”ARC WASHER 4PCS
9

Hardware used for glide ride assembly
N1 BOLT 1/4”*1.5”(6.5MM*37MM) 4PCS
N2R BOLT 1/4’’ *1.7”(6.5MM*43MM) 2PCS
N4 SCREW 0.22”*3/4”(5.5MM*19MM) 4PCS
N5 J-BOLT 2PCS
N6 SPRING WASHER (MEDIUM) 4PCS
N8 CAP BOLT 1/4”*5/10”(6.5MM*14MM) 2PCS
N9 CAP NUT 1/4”4PCS
N10 NUT 1/4”2PCS
N11 SPRING WASHER (LARGE) 2PCS
N12 SPRING WASHER (MEDIUM) 4PCS
Part list for swing seatassembly
J1 PVC COVERED CHAIN
(PRE-ASSEMBLED) 4PCS
J3
EYE BOLT WITH
ATTACHMENT BOLT
(PRE-ASSEMBLED)
8PCS
K1 SWING SEAT 2PCS
Hardware used for swing seat assembly
J6 NYLON NUT 5/16’’ 8PCS
J7 5/16’’ WASHER 4PCS
J8 PLASTIC CAP (WITH WASHER) 4PCS
J9 PLASTIC CAP (WITH LARGE WASHER) 4PCS
10

Parts used for rocking horse assembly
H1 HORSE PART 1 1PC
H2 HORSE PART 2 1PC
H3 HORSE PART 3 1PC
H4 FRONT LEFT LEG 1PC
H5 FRONT RIGHT LEG 1PC
H6 BACK LEFT LEG 1PC
H7 BACK RIGHT LEG 1PC
H8 HORSE GRIP TUBE 1PC
H9 HORSE SEAT 1PC
H10 HORSE BACK 1PC
H11 HORSE SUPPORT 1PC
H12 HORSE FRONT SUPPORT 2PCS
R3 BRACKET 2PCS
R8 BRACKET CLAMP 2PCS
H15 PVC COVERED CHAIN
(PRE-ASSEMBLED) 4PCS
H16A
LONG EYE BOLT WITH
ATTACHMENT BOLT
(PRE-ASSEMBLED)
4PCS
H16B
SHORT EYE BOLT WITH
ATTACHMENT BOLT
(PRE-ASSEMBLED)
4PCS
H17 FOAM TUBE 2PCS
11

Hardware used for rocking horse assembly
D1 BOLT 1/4”*4/5”(6.5MM*20MM) 10PCS
D2 BOLT 5/16”4.2”(8MM*106MM) 4PCS
D3 5/16”WASHER 16PCS
D4 NYLON NUT 5/16’’ 20PCS
D5 BOLT 5/16”*6.3”(8mm*159MM) 2PCS
D6 BOLT 5/16”*6.4”(8MM*162MM) 2PCS
D7 BOLT 1/4”*1.2”(6.5MM*30MM) 4PCS
D8 1/4”ARC WASHER 8PCS
D9 CAP NUT 1/4”4PCS
D10 PLASTIC CAP (WITH LARGE WASHER) 8PCS
D11 PLASTIC CAP (WITH WASHER) 4PCS
D12-1 BOLT 5/16”*3.3”(8MM*85MM) 4PCS
D13 REINFORCING STEEL SPACER 4PCS
Parts used for slide assembly
X1-N SLIDE SUPPORT (WITH OPENING) 1PC
X2-N SLIDE SUPPORT 1PC
X3-N SLIDE LEG TUBE 2PCS
X4-N SLIDE TOP SUPPORT BAR 1PC
X5-N SLIDE FRONT SUPPORT 1PC
X6 SLIDE LADDER STEPS 2PCS
Y2 SLIDE 1PC
12

Hardware used for slide assembly
Y1 PLASTIC CONNECTOR 2PCS
Z1 BOLT 1/4”*1.5”(6.5MM*38MM) 6PCS
Z2 BOLT 1/4”*5”(6.5MM*127MM) 2PCS
Z3 SPRING WASHER (LARGE) 4PCS
Z4 CAP NUT 1/4”10PCS
Z5 CAP BOLT 1/4”*1/2”(6.5MM*14MM) 4PCS
Z6 SPRING WASHER (MEDIUM) 20PCS
Z7 BOLT 1/4”*3”(6.5MM*75MM) 6PCS
13

ASSEMBLY INSTRUCTIONS
Place the playground equipment on level ground and not less than 6ft (1.8m)
from any structure or obstruction such as a fence, garage, house, overhanging
branches, laundry line, or electrical wires.
Do not install the playground equipment over concrete, asphalt, packed earth,
or any other hard surface; a fall onto a hard surface can result in serious injury
or death to the equipment user.
TIGHTENING NUTS & BOLTS
For ease of installation, do not over-tighten the nuts and bolts when you are
assembling your playground equipment. This will allow for some possible
adjustments later on.
Once you have finished the assembly of the playground equipment, go back
over all of the nuts and bolts, properly tighten all of them and close up the plastic
caps before using the playground equipment.
Main frame layout
A5
A2
A3
A4
A4
A4
A4
A4 A6
A5
A1
A4 A4
A4
A5
14

NOTE:
1. Do not over-tighten the nuts and bolts at every step.
2. Do not snap in the cover of plastic cap until you have finished the assembly of
each step and went back to tighten all of the nuts and bolts.
STEP 1
Insert A1 into A2 as shown below and secure with B1, B5, B4 and B3.
Insert A3 into A2 as shown below and secure with B1, B5, B4 and B3.
Note: Please make sure that all concave holes face down and all round holes
face up.
C2
A1
B3
B3
B4
B4
A3
C2
A2
B5
B5
B1
B5
B1
B5
Round holes
face up
Concave holes
face down
B1
B1
15

NOTE:
1. Do not over-tighten the nuts and bolts at every step.
2. Do not snap in the cover of plastic cap until you have finished the assembly of
each step and went back to tighten all of the nuts and bolts.
A3
B3
A4
B3
B6
B4
B1
A6
B6
A4
B1
B4
STEP 2
Insert the small ends of A4 into
the sockets at the end of A1 and
align holes.
Secure using B1, B5, B4 and B3.
Repeat the above steps to
assemble A2 and A3 in the same
manner as A1.
STEP 3
Attach A6 onto the A4 on the end
of A3.
Secure using B1, B6, B4 and B3.
Attach A5 to the remaining A4
on A3, as well as A1 and A2.
B1 B5
A4
B3
B4
B5 B1
A4
A1
B3
B4
16

NOTE:
1. Do not over-tighten the nuts and bolts at every step.
2. Do not snap in the cover of plastic cap until you have finished the assembly of
each step and went back to tighten all of the nuts and bolts.
STEP 4
Slide the small end of R4 into the pocket of R7.
Insert all four R4 into the pocket of R7.
Insert the small ends of R4 into larger ends of adjacent R4 and align holes.
Note: Elliptical holes face up, round holes face down. See below.
R7
R4
R4
R4
R4
Elliptical hole face up
R7
R4
R4
R4
R4
elliptical hole
face up
round hole
face down
Round holes face down
Elliptica hole face up
17

NOTE:
1. Do not over-tighten the nuts and bolts at every step.
2. Do not snap in the cover of plastic cap until you have finished the assembly of
each step and went back to tighten all of the nuts and bolts.
STEP 5
Attach R8 and R3 to A1.
Secure using F2, F3 and F1-1.
STEP 6
Insert the bolt of R2B (which is pre-assembled with R1) into holes of R4.
Secure using F4 and F3.
Assemble the remaining three R2B chains to R4 in the same way.
See figure below.
R3
F2
F3
F2
F3
R8
F2
R3
F3
F2
R8
F1-1
F3
F1-1
R1
R2B
F4
F3
R1
F4
R2B
F3
R2B
R
1
R1
F4
R2B
F4
F3
F3
R4
18

NOTE:
1. Do not over-tighten the nuts and bolts at every step.
2. Do not snap in the cover of plastic cap until you have finished the assembly of
each step and went back to tighten all of the nuts and bolts.
STEP 7
Insert the bolt of R2A (which is pre-assembled with R1) into R3.
Secure using F2 and F3.
You have finished the flying saucer assembly, see Figure A below.
Figure A
F2
F3
R1
R2A
F2
F3
R2A
R3
A1
F3
F2
F3
F2 R2A
R2A
R1
R1
R3
19