SPORTSPOWER JET MAT MSC-5019 Quick setup guide

Assembly and Use Instructions
JET MAT
Model # MSC-5019
- Mature adult supervision is required at all time during use.
- Only for domestic use.
For customer service or replacement parts, please call 1-866-370-2131 Monday
through Friday 9am-5pm EST, visit our website: www.sportspowerltd.net or
email: [email protected]
RETAIN THIS MANUAL FOR FUTURE REFERENCE

• This product is for household and family domestic use only – It is not for use in
schools, playgrounds, rental or commercial use.
• The product must be placed on a surface that is COMPLETELY FLAT AND LEVEL.
If the ground is uneven, this could cause movement in the product that could cause
product damage and/or serious injury.
• DO NOT position this product on a hard surface such as concrete, tarmac or
pavement. Suitable surfaces are grass, sand or a play area covered with an
appropriate depth of protective material.
• Maintain clear space on all sides of the product. Make sure there are no
hazardous objects above, below or near the product. Such objects include walls,
fences, tree limbs/trunks, electrical power wiring, rocks, sprinkler heads or other
recreational objects (i.e. swing sets, swimming pools). Children can be seriously
injured by colliding with such obstacles.
• Always consult your physician before performing any kind of physical activity.
• Do not use or leave the product out in the rain or during windy conditions. These
conditions can cause the user to lose control and suffer injuries.
• The product must be used with the anchors provided and installed properly.
• Ground stakes must be completely inserted into the ground so that no part of the
stake is protruding above the ground surface. This will help prevent tripping or
injuries resulting from a fall.
• Do not use the product while holding or wearing any type of sharp or pointed
objects such as jewelry, watches, rings, eyewear, hair clips or necklaces.
• Always use the product in a well-lit area. Do not use during times with poor lighting
such as dawn, dusk or in complete darkness!
• No shoes or glasses are to be worn on the JET MAT.
• Do not consume food, drink and chew gum while using the product.
• Do not allow pets in or around the product.
IMPORTANT SAFETY INSTRUCTIONS
1

• Make sure the anchors are fully secured and there are no tears or leaks on the
product.
• Product should be dried and stored immediately following use. Do not leave product
exposed outdoors for extended periods as product will be damaged by external
factors such as UV rays , rain and wind. In particular, do not leave outside during
windy days.
• Make sure the product is fully dry before storing, and store only in a cool, well
ventilated and dry location when not in use.
• Must be stored and kept out of reach of children and protected from pests or pets
that can damage the product.
• Product must be fully inspected before and after each use. This is very important to
ensure proper safety and maintenance of the product.
• Remove batteries from the control unit when the JET MAT is not in use.
CARE AND MAINTENANCE
2

-3-
1Jet Mat
Controller
Stakes
1
4
1
2
3
Part Picture
Key
Number Description Quantity
Parts List

Step 1.
Unfold the product.
1
1
1
-4-
Assembly Instruction

-5-
NOTE: Ground stakes must be completely inserted into the ground.
Step 2.
Secure the product to the ground with stakes provided.
Assembly Instruction
3
1
1

-6-
Step 3.
To assemble the controller, unscrew the battery lid then remove the
battery rack and install eight D size batteries (not included). Then
screw battery lid back in place.
Assembly Instruction
2

A
B
D
E
2
-7-
Step 4.
Unscrew the caps from controller and pass them through the water
tubes located on the JET MAT.
Assembly Instruction
1
A
B
D
E
1

A
B
D
E
A
B
E
D
1
1
2
-8-
Step 5.
Push the clear tubes into the matching injector on the control unit.
Make sure each tube is matched to the correct injector as labelled.
Then screw the caps on tightly to the injector.
Assembly Instruction

1
2
-9-
Step 6.
Connect to water hose.
Assembly Instruction

1
-10-
Step 7.
Press the switch to activate the JET MAT. LED indicator will light up
when product is on.
Assembly Instruction
2