SPORTSPOWER PERSONALISED WOODEN PLAYHOUSE Owner's manual

([phone]
Tips: It will take 2 adults
around 60 minutes to
assemble.
Important
Limit:
Age:3 - 10 years
Maximum user: 2
Warning: Only for domestic use
Warning: Only for outdoor use
PERSONALISED WOODEN PLAYHOUSE

Safety Information
Parts
Assembly Instructions
Care and Maintenance
2-3
4-6
7-11
12
1

2
IMPORTANTWARNINGS AND INSTRUCTIONS
Safety Information
BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and using
this product.The unit must be assembled by adults. Heavy duty working gloves should be worn to avoid
injuries during assembly.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT









This product is intended for use by children ages 3-10 years.
On-site adult supervision is requiredat all times for children of all ages.
Do not allow use by children with any physical condition that may affect his/her ability to use this
Children must NOT play with this set until it is properly assembled and inspected by an adult.
Do not allow children to climb on or jump off the play house.
Maximum 2 children inside playhouse at a time.
DO NOT allow children under three years old nearby during assembly. Small parts may cause
choking hazard.
Hardware:
Inspect all nuts and bolts and tighten if required. Hardware should be firmly against, but not
crushing the wood. Over-tightening hardware crushes wood fibers and can split wooden
components resulting in the bolt thread extending beyond the wood. This poses a severe safety
hazard. If bolt threads protrude beyond the wood surface, replace the bolt with a shorter one that
will not protrude. If splintering has occurred from over-tightening, larger washers can be
purchased at your local hardware store and installed under the bolt head. Be sure to reuse or
replace your lock washers.
Major Wooden Parts:
Inspect for structural defects and splintering. If necessary, lightly sand and refinish with an
exterior water repellent stain. Seasonal checking or cracking of the grain on wooden parts is
quite natural, water and heat are the most frequent causes of expansion and contraction of wood
fibers. Our wood set has been treated with stain to resist weathering. But it needs to be
maintained periodically by applying new stain or paint.
equipment safely.
p
ortant
–
Please read these instructions thorou
g
hl
y
before assembl
y
or use.
Failure to follow these important requirements may result in the warranty being voided and/or
serious injury. Please supervise your children carefully during the installation and assembly of the
product.
Please also pay close attention to the periodic maintenance that is required to keep your set in a
safe condition for maximum enjoyment of backyard fun!

3
IMPORTANTWARNINGS AND INSTRUCTIONS
Safety Information
BEFORE YOU BEGIN ASSEMBLY:
Take a complete inventory of components using the parts list.
Sort and lay out the wood pieces. Label each piece of wood for easy reference. For easy
identification during the assembly process, write the board’s letter on masking tape and adhere to
each piece of the wood. Some wooden components may twist or warp in the carton after packaging.
Usually, these parts straighten out when assembled. You may also see some cracking of the grain.
This is normal.
Sort all hardware according to size. Do not worry if extra hardware is included.
FIND A SAFE PLAY LOCATION.
You MUST install the product on level ground. Uneven ground must be leveled prior to installation.
The manufacturer cannot assume responsibility for any failure from incorrect installation.
Installingonsloping ground will put stress on all the joints, which will cause the set tobecome loose
and unstable.
Find a location where the equipment can be placed more than 2 meters from any structure or
obstruction (ex: electrical wires, branches, house, fence, garage). The safe play area refers to a zone
extending 2 meters beyond the gym set on all sides, includingthe space above the play set.
The safe play area must be free of all structures, landscaping, tress and branches, rocks, wires and
other obstacles tosafe play. Children can be seriously injured running into these obstacles.
Remove any rocks or any jagged or sharp object that could endanger your children’s’ safety.
Remove all tripping hazards from the safe play area. Tripping hazards include but are not limited to:
roots, stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing, and electrical
connections.
Do NOT install your play set over gravel, asphalt, packed earth or any other hard surface.
Important –Please read these instructions thorou
g
hly before assembly or use.

([phone]
Please check you have all the parts listed below
NO. PICTURE QTY
AZ1 1
AZ2 1
AZ3 1
AZ4 1
AZ5 2
AZ6 2
4

5
([phone]
Please check you have all the parts listed below
NO. PICTURE QTY
AZ7 2
AZ8 2
1
1
AZ9
AZ10
2
1
AZ11 1
AZ12
AZ13
AZ14
1

6
Note: The quantities below are the correct amount to complete the assembly. In some cases more
([phone]
Please check you have all the parts listed below
Phillips Head Screwdriver
Phillips Head Screwdriver
Electric Drill
Working Gloves
Ladder or Step Tool
REQUIRED ASSEMBLY TOOLS (NOT INCLUDED)
×6 (M3.8×25mm)
×4 (M3.0×18mm )
×12 (M3.8×28mm) ×29 (M3.8×40mm)×6 (M3.8×35mm)
L4 L5 L11L6
L15
Allen Wrench
5

7
● Connect AZ6 to AZ5 using
L11(6pcs) as shown in
Figure 1.
● Connect AZ3 to AZ4 using
L11(3pcs) as shown in
Figure 2.
Assembly Instructions
Step 1
Step 2
FIGURE 1
FIGURE 2
X2
Part No
AZ5
AZ6
Quantity
2
2
Hardware No
L11
Quantity
6
Part No
AZ3
AZ4
Quantity
1
1
Hardware No
L11
Quantity
3
L11
L11
L11
AZ3
AZ4
AZ6
AZ5
L11
L11
L11

● Connect AZ6 to AZ4 using
L11(4pcs) from inside.
● Connect AZ5 to AZ3 using
L11(4pcs) from inside as
shown in Figure 3.
● Connect AZ13 to AZ1 and
AZ2 using L4(3pcs).
Note: Hole on AZ13 must face
upwards.
● Connect AZ10 to AZ1 and
AZ2 using L4(3pcs).
Note: Spacing between AZ1 to
AZ2 should be 32.1cm as
shown in Figure 4.
Step 3
Step 4
Assembly Instructions
FIGURE 3
FIGURE 4
FRONT
BACK
hole face
upwards
32.1cm
Hardware No
L11
Quantity
8
Part No
AZ13
AZ10
AZ1
AZ2
Quantity
1
1
1
1
Hardware No
L4
Quantity
6
8
L11 L11
AZ13
AZ13 AZ13
AZ10 AZ10
AZ1
AZ1
AZ2 AZ2
AZ1
L4
L4
AZ3
AZ3
AZ4
AZ5
AZ5
AZ6

● Connect AZ14 to AZ12 using
L6 (2pcs).
● Connect AZ12 to AZ2 using
L15 (4pcs) as shown in
Figure 5.
Note: Make sure AZ12 and
AZ2 are properly aligned.
● Connect the frames
assembled in steps 3 and 5
to form the playhouse from
inside playhouse.
● Connect AZ5 to AZ1 using
L11(4pcs).
● Connect AZ6 to AZ2 using
L11(4pcs).
● Connect AZ11 to AZ1 using
L6(4pcs) as shown in
Figure 6.
Step 5
Step 6
Assembly Instructions
FIGURE 5
FIGURE 6
Inside view
Part No
AZ12
AZ14
Quantity
1
1
Part No
AZ11
Quantity
1
Hardware No
L6
L11
Quantity
4
8
AZ11
Hardware No
L15
L6
Quantity
4
2
9
AZ12
AZ14
AZ2
AZ12
AZ2
L15
AZ1
AZ6
AZ6
AZ5
AZ5
AZ2
AZ2
AZ1
L11
L11
L6
L6
AZ14
AZ12