Sprout PIKLER CLIMBING TRIANGLE User manual

CLIMBING TRIANGLE
PIKLER
ASSEMBLY GUIDE

PARTS
CLIMBING TRIANGLE
PIKLER
ASSEMBLY GUIDE
INCLUDED TOOLS
Hex Bit
26.75”
28.125”
Dowel Pin extending
from back of this hole
Bolts Screws
Outer Leg Left
A
Long Dowels
F
4mm Allen
Wrench
long & skinny
I
Sandpaper
i
3/16” Allen
Wrench
short & fat
H
G
e
Short Dowels
E
Outer Leg Right
B
Inner Leg Left
C
Inner Leg Right
D
Metal Insert pressed
into back of this hole
J
K L
(7x)
(6x)
(2x) (26x)

Starting with Inner Leg Right d , insert one of the Short Dowels e into
the top indented space. Pushing the end of the Dowel e up against a
corner for balance, insert Screw h into the drilled hole and tighten with
drill and Hex Bit J , or 4mm Allen Wrench i .
1
J
E
E
I
H
D
e
h
i
I
H
E
Hold dowel in
place to prevent
twisting while
tightening screw.
D
If using a drill, set clutch on drill to LOW SETTING (around 3).
If your drill has two speeds, set it to the SLOW SPEED (1).
A high clutch setting will strip screw heads or wood and can render
parts useless!
CLUTCH TOO HIGH: If the drill twists dramatically in your hand when
drilling. Lower the clutch setting.
CLUTCH TOO LOW: If the screw does not screw in all the way. Adjust
clutch up by 1 setting and try again.
STRIPPED WOOD: If the screw continuously spins in place, the wood
has stripped. To x, insert a toothpick into the stripped hole and break
the top o so it's even with the hole opening, then try again. If needed,
add additional toothpicks until the screw stops spinning in place.
3
4
2
2
3
3
4
2
1
12
12
Enjoy the best assembly experience
sprout-kids.com/ct
ASSEMBLY VIDEO

Repeat with the remaining Short Dowels E using Screw H and a drill
and Hex Bit J , or 4mm Allen Wrench I .
2
Once all Short Dowels are tightened into place on Inner Leg Right d , line
up the dowels with the indents on the surface of Inner Leg Left c and
screw into place.
3
Set aside the nished inner half. Following instructions in Steps 1 & 2,
tighten six Long Dowels f into place (with Screw H and using a drill and
Hex Bit J , or 4mm Allen Wrench I ) into Outer Leg Right b . Do not
repeat Step 3.
4
f
b
F
F
I
I
H
H
B
B
J
IJ
EH
C
C
D
D
e
E
Hold dowel in
place to prevent
twisting while
tightening screw.
H
H
I

Align Outer Leg Left A with unattached ends of the Long Dowels F , do
not screw dowels in place yet. Place the nished Inner Legs ( C & D )
on the inside of both Outer Legs ( A & B ).
5
Place Bolts G in the aligning holes on the tops of both the outer and
inner legs. Use Allen Wrench K to tighten.
6
Once both Bolts G are in place, ensure Outer Leg Left A is aligned with
unattached ends of the Long Dowels f . Tighten into place with Screw H
using a drill and Hex Bit J , or 4mm Allen Wrench I .
7
K
K
G
G
G
f
F
F
I
I
H
H
J
Align legs so Dowel
Pin in the hole on
parts C & D goes
into the middle of
the sliding slot on
parts A & B .
B
B
c
C
C
d
D
D
A
A
A
A

When opening the Climbing Triangle for the rst time, you will hear a
cracking noise. This is by design; the noise is from the sliding slot which
allows the triangle to click open and closed. Feel free to open and close it
a few times to try it out.
Add ramp accessories as desired.
*

WWW.SPROUT-KIDS.COM
PO BOX 1123, PROVO, UT 84601
QUARK ENTERPRISES 2022
DOCUMENT: AI-CT