SPUTNIK MODULAR SELECTOR User manual

SELECTOR
MANUAL V.1
SPUTNIK-MODULAR.COM
SPUTNIK MODULAR

SELECTOR
SPUTNIK-MODULAR.COM
SPUTNIK MODULAR
TABLE OF CONTENTS
SPECIFICATIONS
INSTALLATION
DESCRIPTION
DIAGRAM
WARRANTY
3
4
5
6
7

SELECTOR
SPUTNIK-MODULAR.COM
SPUTNIK MODULAR
SPECIFICATIONS
FORMAT:
EURORACK
DIMENSIONS:
6HP, 28mm deep
INTERNAL AND EXTERNAL SIGNALS (3.5mm Jacks):
CV: 0-5V, AUDIO: +/-5V
MAX CURRENT:
+12V: 15mA
-12V: 10mA
+5V: 10mA

SELECTOR
SPUTNIK-MODULAR.COM
INSTALLATION
Remove module from packaging.
Power down your modular synthesizer and disconnect the power
cable from the wall outlet.
Attach the included power cable to the module’s power connector and
connect the other end to the power distribution bus in your EuroRack
synthesizer case. If you have a bi-colored ribbon cable the red stripe
should be on a same side with a bold white line on a pcb. In case if you
have a rainbow-colored ribbon cable the key is brown. Connector also
has a key which should match sikscreen on a pcb.
Position the module on the mounting rails in your EuroRack case and
screw down mounting screws. Power up! If your case does not turn on
properly then you have installed the module incorrectly. Simply power
down and make sure to follow the diagram when reconnecting the
module.
1
2
3
4
BI-COLORED RIBBON
WHITE STRIPE
–12V
RAINBOW RIBBON
WHITE STRIPE
–12V
KEY
SPUTNIK MODULAR

SELECTOR
SPUTNIK-MODULAR.COM
The SPUTNIK SELECTOR is a sequential switch that allows the automated
routing of one of four inputs to a single output. The Selector is able to
switch between 2, 3, or 4 of the inputs and four direction modes (three on
the front panel and one “hidden” mode) are available. Input selection can
be advanced by a trigger/gate input or manual button.
This module may be used as an expansion with a 5-STEP VOLTAGE
SOURCE or 16-STEP VOLTAGE SOURCE modules allowing to switch
between rows and extend these modules up to 20 or 64 steps depending
on the model.
SPUTNIK MODULAR
DESCRIPTION

SELECTOR
SPUTNIK-MODULAR.COM
IN
Four inputs accept CV or audio
signals with stage selection LED
indicators.
OUT
Signal output and Inverted
voltage output.
PLAYBACK
STEPS
Three mode switch allowing for
selection between 2, 3, or 4 inputs.
DIRECTION
Choose between 3 sequential modes
at a time: UP (DCBA pattern), DOWN
(ABCD pattern), or RAND (random
pattern mode). PENDULUM mode
(ABCDCBA pattern) is also available
as a hidden feature when pressing
and holding the “TRIG” and “RESET”
buttons simultaneously for 3
seconds. This will swap UP with
PENDULUM mode and is reversible
by repeating the same process.
TRIG
Selection can be advanced by
trigger, gate, or clock signals via an
input jack or using the dedicated
trigger button for manual selection
at slower speeds.
RESET
Trigger input, gate input, or manual
momentary button control of
sequence reset. Reset defaults
Selector back to Input A.
SPUTNIK MODULAR

SELECTOR
SPUTNIK-MODULAR.COM
WARRANTY
This product is covered by the Sputnik Modular warranty, for one year
following the date of purchase. This warranty covers any defect in the
manufacturing of this product. This warranty does not cover any damage
or malfunction caused by incorrect use – such as, but not limited to, power
cables connected backwards, excessive voltage levels, or exposure to
extreme temperature or moisture levels.
The warranty covers replacement or repair, as decided by Sputnik Modular.
Please contact customer service via our website
(www.sputnik-modular.com) for a return authorization.
SPUTNIK MODULAR