Square Perfect SP4200 User manual

SP4200 VARIABLE POWER
STUDIO FLASH SET
Make every picture perfect

Qty. 3 Professional Studio Digital Strobes
(200 Watt-Seconds) 75-watt modeling light.
Qty. 1 Boom and counter weight bag
with carrying case.
Qty. 3 Light Stands (extends 39" to 8’1/2”)
Qty. 3 Softbox (24" X 24")
Qty. 1 Umbrella (36" silver reflection umbrella)
Qty. 1 Strobe Case (Carries three strobes and accessories)
Qty. 1 Carry Bag (Carries three light stands and umbrella)
Qty. 1 Backdrop stand with carry bag
Qty. 1 10’x20’ Backdrop
Qty. 2 10’x13’ Black and 10’x13’ White backdrop
SP200
Accessories:
Qty. 1 Collapsible
(22" double sided - Silver/White)
Qty. 1 Four Leaf Barndoor
Qty.1Set of 4 Color Gels
Qty. 1 Honeycomb Diffusion Filter
Qty. 1 Narrow Snoot
Reflector
SP4200 Professional Series Studio Light Kit
K
K
www.squareperfect.com
O
L
M
N
O
N
M
L
K

SP4200 Flash Studio Kit
Thank you for your purchase of the SP4200 Flash Softbox Studio Please read this manual carefully before use, and keep it handy
kit. This manual has been written to help you with the assembly, for use during break down of equipment. Please read and heed all
operating procedures and accessories. Square Perfect's SP4200 safety precautions listed in this manual. To order spare bulbs
Flash Kit is manufactured with the finest material available. Your or replacement parts, contact us at [email protected].
flash kit will provide many years of quality service with proper care Also check out our extended line of photo equipment now
and handling. available.
Flash Studio Kit Includes:
1x2 SP200 lamp body.
12' power cord.
Nylon Carry Case. Compartmentalized for easy use
1 Four leaf barndoor.
1 set Red, blue, yellow frosted
and honeycomb filter.
1x3 Four panel softbox set.
with lamp connector.
Electronic radio trigger /
receiver with sync cord and
adaptors.
1x1 Snoot will direct light to
exact spot without
affecting surrounding
area.
1x1 Varigated dye backdrop
1x1 Black backdrop
1x1 White backdrop
1x1 Umbrella - double
layered reflective
inside,light proof
backing.
1x1 Complete backdrop stand with
carry case
1x1 Flat reflector for creative
fill techniques,
includes carry case
1x1 Twelve foot boom with adjustable
weight counter balance bag.
1x3 SP8061 professional duty
adjustable light stand.
Stand extends from 39" to 8'1/2".
1x3 Four panel softbox set.
with lamp connector.

1. Pictured is the SP4" lamp ring
connector shown with the
large end of the flex rod inserted.
2. Small end of flex rod fitsinto
corner pocket on the softbox
tent.
3. With three rods inserted into
the ring and corners, fold the
SP 4" ring into the tent.
5. Insert the forth rod into the
pocket on the velcro strap.
6. Push the velcro strap into
place just below the lip of the
tent.
deal of force to flex into position.
Note: the rods take a good
7. Now close the velcro flaps
as shown in the picture.
8. The SP 4" ring can now be
attached to the SP 160 flash unit.
DO NOT over tighten.
9. Next attach the inner diffusion
lens with the velcro straps.
10. Attach the outer diffusion
lens to velcro patches on
the outer edges.
SAFETY PRECAUTIONS:
•Become thoroughly familiar with this product before use. Run •Wait until the bulb is completely cool before touching or
through at least one practice assembly and breakdown before removing it.
you schedule a shoot. •Never use the SP160 lamp outside in a wet environment.
•Make sure that the main voltage corresponds to that stated on •Never move the appliance by pulling the cord. Make sure the
the SP160 lamp. Account for number of lamps in use. cords do not come in contact with halogen bulb. Do not wind
•Never leave the lighting unsupervised when in use. Keep the cord around the appliance.
children or incompetent persons away from lighting equipment. •Stand the SP160 on a flat surface only to prevent toppling.
•If the lamp or the cord show sign of wear or damage, it should •Do not touch the metal parts on the lamp while in use, these
be replaced or repaired by a qualified electrician before use. metal parts will become very hot.
Softbox Assembly:
4. Next insert the fourth rod
into the SP 4" ring. Note: Keep
the velcro flaps at the ring
open to allow sufficient slack.
1. On/Off electric supply.
2. Variable flash buttons.
3. On/Off variable, model lamp.
4. On/Off flash ready beep.
5. Flash test.
6. Sync receptacle.
7. Safety fuse.
8. AC receptacle.
1.
2.
3.
9.
5. 8.
7.
Specifications:
SP200 Lamp Head Operation:
Power Input : AC110-130 volt, 50 Hz
Flash Power : 200w (joule) in full
Guide No. : GN45
Color Temperature : 5600K
Flash-Tube Lifetime : over 8,000 typical flashing
Flash Power Setting : 1/32 to full
Recharge Time : 2 seconds in full
Flash Duration : 1/600 sec.; 1/1000 sec.
Slave Range : 35ft /10m
Lighting Range : 55 degree
Modeling Power : Halogen 100w
Synch Voltage : 5 volt
Fuse : 6A
Dimension : 4" x 7-1/2"
Weight : 1.8 Lb (800g)
4.
6.
11.
12.
9. Flash digital readout.
10. Remote button.
11. Flash ring.
12. Model lamp.
8.
9.
10.

Technical Notes for the electronic radio trigger device:
The SP Flash Kit is shipped with the DRT-2G electronic to fit most popular brands.
radio flash triggering device for your convenience. The DRT-2G trigger has two channels and uses a 23A
It is an easy to use device that will give you extra battery (installed). The DRT-2G receiver uses two AAA
control in the photographic studio environment. The batteries (not included).
DRT-2G is designed to work with a variety of flash
units. We provide a wide range of sync cord adaptors
www.squareperfect.com
1.To use the DRT-2G trigger device, first
slide the trigger into the hot shoe found
on top on your camera. If a hot shoe is not
available, use the sync cord attachment
found on the side of the trigger device.
3.Switch the receiver unit ON/OFF button to
the ON position. Press the test button
located on the top of the trigger unit. You
will see a twinkling of the LED on the
receiver unit. This indicates the trigger is
working properly and is locked-in on a
working channel of the receiver.
4.Switch the remote flash unit power
switch to the ON position with the DRT-2G
receiver attached. Push the test button
on the DRT-2G trigger, it should trigger
the remote flash unit.
5.To change channels on the DRT-2G
trigger, slide the channel switch on the
side of the trigger device to the opposite
position. Next press the power switch on
the receive unit twice to reset the
receiver.
To order spare bulbs or replacement parts,
contact us at [email protected]. Also check
out our extended line of photo equipment.
2.Attach the receiver to a remote flash unit.
Use the proper sync cord adaptor
provided, plug into sync cord socket.