SSV Works RZ3-GB10 User manual

RZ3-GB10
RZR XP1000 & 2015+ RZR900
Glove Box Subwoofer Enclosure
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects
in material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. All SSV Works Speakers are
covered by a limited 1 year warranty against defects in material or workmanship. Labor
for replacement of defective components is not covered. Contact SSV Works for further
warranty information.
1. WP-RZ3GBS10 Enclosure
2. M6 x 1.0 Screws x 11
(Long)
3. M6 x 1.0 Screws x 2 (Short)
TOOLS NEEDED FOR INSTALLATION
INSTALLATION NOTES
PARTS LIST
PARTS LIST IMAGES
4. M6 Washers x 13
5. Flat Mounting Brackets x 2
6. “L” Bracket x 1
7. Glove Box Door bracket x 1
The use of a thread locker is recommended on all screws to prevent loosening due to vibration. If the vehicle has SSV Works front kick panels
(RZ3-FKP65/RZ3-F65) installed, the passenger side kick panel will need to be removed prior to installation of the RZ3-GB10. Removal of the
passenger fender is not required (Step 3); however it will make the installation and alignment of the RZ3-GB10 easier.
2. M6 x 1.0 Screws x 11
(Long)
7. Glove Box Door
Bracket x 1
3. M6 x 8mm Screws x 2
(Short)
4. M6 Washers x 13
5. Flat Mounting
Brackets x 2
1. WP-RZ3GBS10 Enclosure
(door not included)
6. “L” Bracket x 1
- Wire Crimpers
- Wire Strippers
- 10mm Socket or Wrench
- Drill with 1/8” and 1/4” Drill bits
- T-30 Torx Driver
- T-40 Torx Driver
- #3 Phillips Screwdriver
- #2 Phillips Screwdriver
- Panel removal tool

A. Remove the hood, remove the two T40 Torx bolts that secure
top center dash. From inside the vehicle, release the dash
by gently pulling toward the rear of the vehicle. Place center
dash to the left
C. Remove the ten T40 Torx bolts that secure the 2 piece fender.
Note: there is one screw inside the fender well. Remove the
two additional screws from the striker plate, slide fender up
the cage rail and secure
B. Remove the two T40 Torx bolts that secure the front dash.
Carefully release the panel clips along the perimeter of the
dash by pulling toward the rear of the vehicle, remove front
dash and set aside
D. Remove the two 10mm bolts the secure factory glove box and
remove the factory glove box
RZ3-GB10
A
C
B
D
SSV HOLE PATTERN
KICKER HOLE PATTERN
FOR UNLOADED ENCLOSURES:
Pink hole pattern: SSV Works Subwoofer
Blue hole pattern: Kicker Subwoofer
If using a different brand subwoofer, rst see if the
subwoofer holes line up with either one of the pre-
drilled hole patterns. If not, make sure to drill new
holes away from the pre-drilled holes.

E. Lift the enclosure into place and align the top channel in the grab handle
bar, while holding the enclosure in place, loosely attached the at brackets
to the top of the enclosure using the long screws provided.
G. While applying pressure keeping the enclosure secure against
the front wall, tighten the top brackets, as they tighten they
will bend slightly to add pressure and avoid any vibration, now
tighten the lower L bracket to the enclosure
F. To properly align the box, slide the box rmly toward the front of the
vehicle. It should sit approximately 1/4” from the factory glove
box mount. If not properly installed, the dash of the vehicle will
not securely push back into position.
I. For 2015-up model year vehicles, install the supplied bracket using
the short screws provided and adjust forward or back so glove box
latch closes tight
H. Loosely install the bottom L bracket, align the mounting hole with
the factory bung and secure with one of the long screws provided
(you will tighten the bracket to the enclosure and factory bung
AFTER step J)
RZ3-GB10
F
E F
G
E
I
H
J. For 2014 model year vehicles remove the factory glove box
door latch. Mount the latch to the supplied bracket and
secure to the enclosure using the short screws provided
J

RZ3-GB10 © 2017 SSV Works, Oxnard, CA 93030 RZ3-GB10 Rev. A 5-25-17
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using
with an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
“+”
“+”
“ - ”
“ - ”
Amplier
K. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier.
K
J. Attach the factory glovebox door and all panels previously
removed.
J