Stance Healthcare 6085 User manual

Your table may vary from this illustration
45 Goodrich Drive, Kitchener, Ontario, Canada N2C 0B8 tel [phone] fax [phone] www.stancehealthcare.com
Stance 6085 Treatment Tables
Assembly Instructions
• Model #ST6085 Treatment Table only
• Model #ST6085-SH Treatment Table with Shelf
• Model #ST6085-DW Treatment Table with Shelf and Two Drawer Cabinet

Thank you for purchasing the 6085 StanceTreatmentTable. You will find this solidly engineered product
will give you years of reliable service.
Four your safety and that of the patient it is very important that this table is assembled according to
these instructions!
Items Included in the Carton(s):
Stance ST6085 Treatment Table only:
1) Treatment Table
2) Paper Roll Holder
3) Fastener Kit:
a. Four (4) 1/4 - 20 x 2-1/2” long Philips drive machine screws
b. Four (4) 1/4 - 20 x 5/8” long Philips drive machine screws
c. Assembly Instructions
Stance ST6085-SH Treatment Table with Shelf:
1) Treatment Table
2) Treatment Shelf
3) Paper Roll Holder
4) Fastener Kit:
a. Four (4) 1/4 - 20 x 2-1/2” long Philips drive machine screws
b. Four (4) 1/4 - 20 x 1-1/2” long Philips drive machine screws
c. Assembly Instructions
Stance ST6085-DW Treatment Table with Shelf and Two Drawer Cabinet:
1) Treatment Table
2) Treatment Shelf
3) Two Drawer Cabinet
4) Paper Roll Holder
5) Fastener Kit:
a. Four (4) 1/4 - 20 x 2-1/2” long Philips drive machine screws
b. Four (4) 1/4 - 20 x 1-1/2” long Philips drive machine screws
c. Four (4) #8 1 1/4” long Philips drive wood screws
d. Assembly Instructions
- Page 2 -

Assembly Instructions for Treatment Table only:
Tools you will need:
1) #3 Philips Screwdriver
1) Place Treatment Table carton right side up and remove all staples to avoid damaging the treatment
Ta b l e .
2) Open carton out flat on the floor to provide a clean assembly area. Roll the Treatment Table onto
the cardboard as shown here.
3) Loosen bubble wrap and remove Fastener Kit, Cross Channel and Paper Roll Holder.
4) Pivot both leg end frames to their full right position and securely fasten the end frame to the
Treatment Table top with the four (4) 1/4 - 20 x 2-1/2” long machine screws provided.
- Page 3 -

5) With the help of an assistant, now rotate the Treatment Table onto its feet.
6) Unpackage the Cross Channel and position onto the support brackets as shown here.
7) Secure the Cross Channel using the four (4) 1/4 - 20 x 5/8” long machine screws provided.
8) With the help of an assistant move theTreatmentTable to the desired location and adjust the levelling
feet with a 7/16” open end wrench, if needed.
9) Remove all packaging material to a recycling bin.
- Page 4 -

Installation Instructions for optional Shelf:
Tools you will need:
1) #3 Philips Screwdriver
1) With the help of an assistant set the Shelf in place as shown.The Shelf drops in on top of cross
channel and will be flush with the two end frame cross bars.The Shelf also rests on an L bracket in
each corner.
2) Secure each end of the Shelf with two (2) 1/4 - 20 x 1-1/2” long machine screws provided.
3) Remove all packaging material to a recycling bin.
- Page 5 -

- Page 6 -
Installation Instructions optional two Drawer Cabinet:
Tools you will need:
1) #3 Philips Screwdriver
2) Electric Screwdriver with #2 Philips driver bit
Important Notice:
Please note that the Drawer Cabinet can be installed on either end of theTreatmentTable or anywhere
along the length of it.
If it is located at the Head end of theTreatmentTable, it must be positioned inward from the front leg
by at a minimum of 1 1/4” to allow space for the paper roll.
If it is located at the Foot end of the Treatment Table, it must be flush with the front leg, as shown
below (left).This is 1) to permit the drawers to open, and 2) to position the screws securing the Shelf
within the recess on the underside of the Drawer Unit (right).
1) Remove the Drawer Cabinet from its packaging.
2) Remove the two drawers from the Cabinet.
3) With the help of an assistant place the Cabinet on the shelf in the desired location following
the Notice above.The Cabinet should be flush with the front and rear edges of theTreatment Shelf.
Con’t
Drawer cabinet
must be flush with
front edge of shelf
and adjacent to leg
Recess
Bottom of cabinet

- Page 7 -
4) Secure the Cabinet to the Shelf using the four (4) #8 x 1-1/4” long wood screws provided.
5) Install the drawers.
6) Remove all packaging material to a recycling bin.

- Page 8 -
Installing the Paper Roll:
If you have any questions regarding these package, please contact us at
877 395-2623, or by email to [e-mail].
Stance Healthcare OM6085 Owners Manual, 6085 Treatment Table, REV 2