Stance Healthcare Oasis Quick start guide

Oasis Recliner
Parts and Service Manual

Oasis Recliner 24”
© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
Page 2

© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
Oasis Recliner Seat Frame and Webbing
Page 3

© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
Optional Central Caster Locking System For Oasis Recliner
Page 4

© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
How to replace the optional
Central Locking Casters
To replace the four casters we recommend placing the sides of
the recliner on wood blocks so that the recliner is about 10” off
the oor. This should be done with one or two helpers.
To Remove the Casters:
1) Rear Casters
a. Loosen the two set screws in the Connecting Levers (item
3) using a 3mm Allen key and a 3/64”Allen key the two set
screws in the collars (item 2).
b. Remove the locking pedal from the hexagon shaft using a
5/32” Allen key.
c. Slide the shaft out of the recliner.
d. Remove the rear casters by pulling them downward out of
the side frames.
2) Front Casters
a. Loosen the two set screws in the Connecting Levers (item
3) using a 4mm Allen Key, and remove the Levers from the
hexagon shafts from the caster actuator assembly.
b. Remove the two machine screws from each CasterActuating
Assembly (item 6) using a #3 Robertson screwdriver.
c. Remove the Caster Actuator Assemblies.
d. Remove the front casters by pulling them downward out of
the side frame.
To Install new Casters:
Very Important: these next steps must be followed in order for
the casters to lock/ unlock properly.
1) Before Installing the Casters
Taking each caster in turn, insert one of hexagon shafts through
the hexagon receptacle in the top of the caster stem and
rotate it counterclockwise with a 7/16” wrench so that the
caster is now in the locked position. If this puts the caster in
the unlock position instead, remove the hexagon shaft, rotate
the caster stem 180 degrees and reinsert the shaft. Rotating
the shaft counterclockwise should now lock the caster. It is
important at this point to note the orientation of the caster as
well: once all four casters have been locked in the prescribed
manner they need to all facing the same way. (See Fig. 1).
2) Rear Casters
a. Maintaining the same orientation as noted in Fig. 1, install
the rear casters.
b. Slide the hexagon shaft through the right side frame and
caster stem until it emerges through the inside of the frame.
c. Slide one of the collars (item 2) on the shaft.
d. Next slide the right side Connecting Lever (item 3) onto
Caster must be
facing this way
Hexagon bushing must be rotated
counter clockwise to lock caster
Fig. 1
Page 5

© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
the hexagon shaft so that is also in the 1 o’clock position
(when looking at it).
e. Now slide the shaft over to the left side of the recliner and
install the left side Connecting Lever in 11 o’clock position
(when looking at it) on the shaft. Slide the second collar
onto the shaft.
f. Next slide the hexagon shaft into the left side frame and
through the left rear caster stem.
g. Orienting the pedal so that it is in the approximate locking
position when looking at it, (the green side of the pedal is
in the 8 o’clock position and the red side is in the 2 o’clock
position), slide it onto the shaft and secure it tightly. You
may have to move the hexagon shaft back and forth a bit
to be sure that it is properly inserted into the pedal. Now
slide the pedal and shaft over so that it is touching the side
of the recliner.
h. In a similar way slide the collars over so they are both
touching the inside of the side frames and tighten the
set screws in them. Do not tighten the set screws in the
Connecter Levers at this point.
3) Front Casters
a. Maintaining the same orientation as noted in Fig. 1, install
the front casters.
b. Install the left and right Caster Actuating Assemblies.
c. Install the two front Connecting levers onto the Caster
Actuating Assemblies (they should only be able to go one
way).
4) Final Steps
a. Next secure the four Connecting Levers adjacent to each
casters. It is important that these are positioned on the rear
hexagon shaft so that the Linkages (item 5) are parallel to
the side frames. Tighten the set screws securely.
b. As a nal step, recline and retract the recliner fully
ensuring that there is no interference between the recliner
mechanism and the Linkages.
Any questions can be emailed to our service department at
ser[email protected] or by phoning 877 395-2623,
ext. 223.
Fig. 2 Front left caster Connecting Lever in the Locked position
Page 6
Stance Healthcare OMSR900 Owners Manual, Oasis Recliner, REV 1

Accessory Mounting Location - Recliner Left Side
Page 7
© Copyright Stance Healthcare Inc. 275 Shoemaker Street, Kitchener, ON N2E 3B3 tel [phone] fax [phone] stancehealthcare.com
Stance Healthcare OMSR900 Owners Manual, Oasis Recliner, REV 2, Date: 11/14
A wood plate located on the left side of
the recliner is provided for eld-mounted
accessories, wood screws up to 2” long
may be used to secure the accessory