Stanley J7cs User manual

112

ESPECIFICACIONES

Amperios de impulso: 12V CC, 700A máximo de batería,

350 amperios instantáneos

Tipo de batería: De plomo sin necesidad de mantenimiento,

sellada, CC de 12 voltios

Presión máxima del aparato

para compresor: 120 PSI

Puertos de alimentación USB: 5V DC cada uno, total de 3.1A

Importados por Baccus Global LLC,

621 NW 53rd St., Suite 450, Boca Raton, FL 33487

www.Baccusglobal.com 1-877-571-2391

RD050520

350 AMP BATTERY JUMP-STARTER

WITH COMPRESSOR

INSTRUCTION MANUAL

PUENTE AUXILIAR DE ARRANQUE DE 350A

CON COMPRESOR

MANUAL DE INSTRUCCIÓN

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.

Boca Raton, FL 33487

(877) 571-2391

J7CS/J7CSC

English page 3

Español pagina 11

J7CS_J7CSC_ManualENSP_050520.indd 12-1J7CS_J7CSC_ManualENSP_050520.indd 12-1 5/6/2020 1:31:34 PM5/6/2020 1:31:34 PM

2 3

FEATURES

CARACTERÍSTICAS

10 11

13 14

34 5 6

1416

FEATURES

1. USB Power button

2. USB Charging/Power Ports

3. USB power indicator

4. Battery Status LED Indicators

5. Reverse Polarity Indicator

6. Jump-Starter Power Switch

7. Area Light Power Button

8. Pivoting LED Area Light

9. Battery Power Level Button

10. 12 volt DC charging port (for use with 120 volt AC charger)

11. Air Pressure Gauge

12. Positive (+) Red Clamp

13. Air Hose and Sure Fit®Nozzle Connector

14. Compressor Power Switch

15. Negative (–) Black Clamp

16. 120 Volt AC Charging Adapter

17. Nozzle Adapters

CARACTERÍSTICAS

1. Botón de la energía del USB

2. Puertos de carga / potencia del USB

3. Indicador de energía del USB

4. Indicadores de estado de la batería del LED

5. Indicador de polaridad inversa

6. Interruptor de encendido del puente auxiliar de arranque

7. Botón de encendido de la luz de área

8. Lúz LED giratoria de área

9. Botón del nivel de energía de batería

10. Puerto de carga de 12 voltios CC (para usar con cargador de 120 voltios CA)

11. Galga de presión

12. Pinza roja del positivo (+)

13. Inyector de aire y conector de boquilla Sure Fit®

14. Interruptor del compresor

15. Pinza negra del negativo (–)

16. Adaptador de carga de 120 voltios CA

17. Adaptadores de boquilla

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Este dispositivo cumple con la parte 15 de las normas de la Comisión Federal de Comunicaciones de Estados Unidos (FCC). La operación está sujeta a las dos condiciones siguientes: (1) este dispositivo no puede causar

interferencia perjudicial y (2) este mecanismo debe aceptar cualquier interferencia recibida, incluida la in-terferencia que puede provocar una operación no deseada.

Este equipo ha sido probado y se encontró que cumple con los límites para dispositivo digital Clase B, según la parte 15 de las normas de la FCC. Estos límites están diseñados para brindar protección razonable contra

interferencia perjudicial en una instalación residencial. Este equipo genera, usa y puede irradiar energía en frecuencia de radio y, si no se instala y se usa de acuerdo con las instrucciones, puede provocar interferencia perjudicial

en las comunicaciones de radio. Sin embargo, no hay garantía de que la interferencia no ocurra en una instalación en particular. Si el equipo provoca interferencia perjudicial en la recepción de radio o televisión, lo que se

puede determinar al apagar y encender el equipo, el usuario debe tratar de corregir la interferencia mediante una o más de las siguientes medidas:

• Cambiar la orientación o la ubicación de la antena de recepción.

• Aumentar la separación entre el equipo y el receptor.

• Conectar el equipo a un tomacorriente sobre un circuito diferente de aquel al que está conectado el receptor.

• Consultar al vendedor o pedir la ayuda de un técnico en radio y televisión con experiencia.

Los cambios o las modificaciones no aprobados por el partido responsable de conformidad podían anular la autoridad del usuario para funcionar el equipo.

J7CS_J7CSC_ManualENSP_050520.indd 2-3J7CS_J7CSC_ManualENSP_050520.indd 2-3 5/6/2020 1:31:35 PM5/6/2020 1:31:35 PM

2 3

FEATURES

CARACTERÍSTICAS

10 11

13 14

34 5 6

1416

FEATURES

1. USB Power button

2. USB Charging/Power Ports

3. USB power indicator

4. Battery Status LED Indicators

5. Reverse Polarity Indicator

6. Jump-Starter Power Switch

7. Area Light Power Button

8. Pivoting LED Area Light

9. Battery Power Level Button

10. 12 volt DC charging port (for use with 120 volt AC charger)

11. Air Pressure Gauge

12. Positive (+) Red Clamp

13. Air Hose and Sure Fit®Nozzle Connector

14. Compressor Power Switch

15. Negative (–) Black Clamp

16. 120 Volt AC Charging Adapter

17. Nozzle Adapters

CARACTERÍSTICAS

1. Botón de la energía del USB

2. Puertos de carga / potencia del USB

3. Indicador de energía del USB

4. Indicadores de estado de la batería del LED

5. Indicador de polaridad inversa

6. Interruptor de encendido del puente auxiliar de arranque

7. Botón de encendido de la luz de área

8. Lúz LED giratoria de área

9. Botón del nivel de energía de batería

10. Puerto de carga de 12 voltios CC (para usar con cargador de 120 voltios CA)

11. Galga de presión

12. Pinza roja del positivo (+)

13. Inyector de aire y conector de boquilla Sure Fit®

14. Interruptor del compresor

15. Pinza negra del negativo (–)

16. Adaptador de carga de 120 voltios CA

17. Adaptadores de boquilla

interference that may cause undesired operation.

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

interferencia perjudicial y (2) este mecanismo debe aceptar cualquier interferencia recibida, incluida la in-terferencia que puede provocar una operación no deseada.

puede determinar al apagar y encender el equipo, el usuario debe tratar de corregir la interferencia mediante una o más de las siguientes medidas:

• Cambiar la orientación o la ubicación de la antena de recepción.

• Aumentar la separación entre el equipo y el receptor.

• Conectar el equipo a un tomacorriente sobre un circuito diferente de aquel al que está conectado el receptor.

• Consultar al vendedor o pedir la ayuda de un técnico en radio y televisión con experiencia.

Los cambios o las modificaciones no aprobados por el partido responsable de conformidad podían anular la autoridad del usuario para funcionar el equipo.

J7CS_J7CSC_ManualENSP_050520.indd 2-3J7CS_J7CSC_ManualENSP_050520.indd 2-3 5/6/2020 1:31:35 PM5/6/2020 1:31:35 PM

2 3

FEATURES

CARACTERÍSTICAS

10 11

13 14

34 5 6

1416

FEATURES

1. USB Power button

2. USB Charging/Power Ports

3. USB power indicator

4. Battery Status LED Indicators

5. Reverse Polarity Indicator

6. Jump-Starter Power Switch

7. Area Light Power Button

8. Pivoting LED Area Light

9. Battery Power Level Button

10. 12 volt DC charging port (for use with 120 volt AC charger)

11. Air Pressure Gauge

12. Positive (+) Red Clamp

13. Air Hose and Sure Fit®Nozzle Connector

14. Compressor Power Switch

15. Negative (–) Black Clamp

16. 120 Volt AC Charging Adapter

17. Nozzle Adapters

CARACTERÍSTICAS

1. Botón de la energía del USB

2. Puertos de carga / potencia del USB

3. Indicador de energía del USB

4. Indicadores de estado de la batería del LED

5. Indicador de polaridad inversa

6. Interruptor de encendido del puente auxiliar de arranque

7. Botón de encendido de la luz de área

8. Lúz LED giratoria de área

9. Botón del nivel de energía de batería

10. Puerto de carga de 12 voltios CC (para usar con cargador de 120 voltios CA)

11. Galga de presión

12. Pinza roja del positivo (+)

13. Inyector de aire y conector de boquilla Sure Fit®

14. Interruptor del compresor

15. Pinza negra del negativo (–)

16. Adaptador de carga de 120 voltios CA

17. Adaptadores de boquilla

interference that may cause undesired operation.

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

interferencia perjudicial y (2) este mecanismo debe aceptar cualquier interferencia recibida, incluida la in-terferencia que puede provocar una operación no deseada.

puede determinar al apagar y encender el equipo, el usuario debe tratar de corregir la interferencia mediante una o más de las siguientes medidas:

• Cambiar la orientación o la ubicación de la antena de recepción.

• Aumentar la separación entre el equipo y el receptor.

• Conectar el equipo a un tomacorriente sobre un circuito diferente de aquel al que está conectado el receptor.

• Consultar al vendedor o pedir la ayuda de un técnico en radio y televisión con experiencia.

Los cambios o las modificaciones no aprobados por el partido responsable de conformidad podían anular la autoridad del usuario para funcionar el equipo.

J7CS_J7CSC_ManualENSP_050520.indd 2-3J7CS_J7CSC_ManualENSP_050520.indd 2-3 5/6/2020 1:31:35 PM5/6/2020 1:31:35 PM

4 5

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety

precautions should always be followed to reduce the risk of personal injury.

Improper operation, maintenance or modification of tools or equipment could

result in serious injury and property damage. There are certain applications for

which tools and equipment are designed. Manufacturer strongly recommends that

this product NOT be modified and/or used for any application other than for which

it was designed. Read and understand all warnings and operating instructions

before using any tool or equipment.

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating the jump starter

with compressor. Failure to follow all instructions listed below may result

in electric shock, fire and/or serious injury.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

• This unit was designed for household use only.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST

HAZARD, OR INJURY TO PERSONS OR PROPERTY:

• Avoid dangerous environments. Don’t use appliances in damp or wet locations.

Don’t use appliances in the rain.

• Keep children away. All visitors should be kept at a distance from work area.

• Dress properly. Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and substantial, non-skid footwear are recommended

when working outdoors. Wear protective hair covering to contain long hair.

• Use safety glasses and other safety equipment. Use safety goggles or safety

glasses with side shields, complying with applicable safety standards. Safety glasses

or the like are available at extra cost at your local dealer.

• Store idle appliance indoors. When not in use, appliances should be stored

indoors in dry, and high or locked-up place – out of reach of children.

• Don’t abuse cord. Never carry appliance by cord or yank it to disconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

• Disconnect appliances. Disconnect the appliance from the power supply when

not in use, before servicing, and when changing accessories.

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on

the circuits or outlets to be used. Receptacles are available having built in GFCI

protection and may be used for this measure of safety.

• Use of accessories and attachments. The use of any accessory or attachment

not recommended for use with this appliance could be hazardous. Refer to the

accessory section of this manual for further details.

• Stay alert. Use common sense. Do not operate appliance when you are tired or

impaired.

• Check for damaged parts. Any part that is damaged should be replaced by the

manufacturer before further use. Contact the manufacturer at (877) 571-2391 for

more information.

• Do not operate this appliance near flammable liquids or in gaseous or

explosive atmospheres. Motors in these tools normally spark, and the sparks

might ignite fumes.

• Never submerge this unit or the 120 volt AC charger in water. Do not

expose the unit or the 120 volt AC charger to rain or snow, or use them when wet.

• To reduce risk of electric shock, disconnect the unit from any power source

before attempting maintenance or cleaning. Turning off controls without

disconnecting will not reduce this risk.

• This equipment employs parts (switches, relays, etc.) that produce arcs or

sparks. Therefore, if used in a garage or enclosed area, the unit MUST be placed

not less than 18 inches above the floor.

SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT

• IMPORTANT: This unit is delivered in a partially charged state. Fully charge unit

with the supplied 120 volt AC charger for a full 24 hours before using for the

first time.

• To recharge this unit, use only the supplied charging adapters. Plug in the

charging adapter at the jump starter first, then plug into the charging source.

• After charging/recharging, disconnect charging adapter and wait 5 minutes

before use.

• Do not crush, cut, pull or expose charging adapter cords to extreme heat.

• Pull by plug rather than cord when unplugging the charger.

• Position charging adapter cords so they do not become entangled or become a

safety hazard. Keep charging adapter cords away from sharp edges.

• Use in a dry location only.

• All ON/OFF switches should be in the OFF position when the unit is charging or

not in use. Make sure all switches are in the OFF position before connection to a

power source or load.

• Do not attempt to charge the unit if the charger is damaged – return the charger

to manufacturer for repair or replacement.

Extension Cords

• Outdoor use extension cords. When appliance is charged outdoors, use only

extension cords intended for use outdoors and so marked.

• Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss

of power and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE FOR CORD SETS

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)

240V 0-50 51-100 101-200 201-300

(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)

Ampere Rating Extension Cord Length

More Not more 0’-25’ 26’-50’ 51’-100’ 101’ -150’

Than Than American Wire Gauge (AWG)

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

When an extension cord is used, make sure that:

a) the pins of extension cord are the same number, size and shape as those in the

charger,

b) the extension cord is properly wired and in good electrical condition,

c) the wire size is large enough for the AC rating of the charger.

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

Pull cord by plug rather than cord when disconnecting the 120V AC Charging

Adapter from the unit.

SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS

WARNING: BURST HAZARD

Do not use the unit for charging dry-cell batteries that are commonly used with

home appliances. These batteries may burst and cause injury to persons and

damage property. Use the unit for charging/boosting a lead-acid battery only. It is

not intended to supply power to a low-voltage electrical system other than in a

starter-motor application.

• Use of an attachment not supplied, recommended or sold by manufacturer

specifically for use with this unit may result in a risk of electrical shock and injury

to persons.

WARNING: RISK OF EXPLOSIVE GASES

• Working in the vicinity of a lead acid battery is dangerous. Batteries generate

explosive gases during normal battery operation. For this reason, it is of the

utmost importance that each time before using the jump-starter you read this

manual and follow instructions exactly.

• To reduce the risk of battery explosion, follow these instructions and those

published by the battery manufacturer and manufacturer of any equipment you

intend to use in the vicinity of the battery. Review cautionary markings on these

products and on the engine.

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

• NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.

• Vehicles that have on-board computerized systems may be damaged if vehicle

battery is jump-started. Before jump-starting, read the vehicle’s owner’s manual to

confirm that external-starting assistance is suitable.

• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or

power station

• Remove personal metal items such as rings, bracelets, necklaces and watches when

working with a lead acid battery. A lead acid battery can produce a short circuit

current high enough to weld a ring, or similar metal object, to skin, causing a

severe burn.

• Do not wear vinyl clothing when jump-starting a vehicle when jump-starting a

vehicle, friction can cause dangerous static-electrical sparks.

• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.

• Always store battery clamps when not in use. Never touch battery clamps together.

This can cause dangerous sparks, power arcing and/or explosion.

• When using this unit close to the vehicle’s battery and engine, stand the unit on a

flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts

away from moving vehicle parts.

• Never allow red and black clamps to touch each other or another common metal

conductor — this could cause damage to the unit and/or create a sparking/

explosion hazard.

a) For negative-grounded systems, connect the POSITIVE (RED) clamp to the

POSITIVE ungrounded battery post and the NEGATIVE (BLACK) clamp to the

vehicle chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a

heavy gauge metal part of the frame or engine block.

b) For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the

NEGATIVE ungrounded battery post and the POSITIVE (RED) clamp to the

vehicle chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a

heavy gauge metal part of the frame or engine block.

• If the connections to the battery’s POSITIVE and NEGATIVE terminals are incorrect,

the Reverse Polarity Indicator will light (red) and the unit will sound a continuous

alarm until the clamps are disconnected. Disconnect clamps and reconnect to

battery with correct polarity.

• Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the

POSITIVE (RED) jumper cable, except for positive grounded systems.

• Do not expose battery to fire or intense heat since it may explode. Before

disposing of the battery, protect exposed terminals with heavy-duty electrical tape

to prevent shorting (shorting can result in injury or fire).

• Place this unit as far away from the battery as cables permit.

• Never allow battery acid to come in contact with this unit.

• Do not operate this unit in a closed area or restrict ventilation in any way.

• This system is designed to be used only on vehicles with a 12 volt DC battery

system. Do not connect to a 6 volt or 24 volt battery system.

• This system is not designed to be used as a replacement for a vehicular battery. Do

not attempt to operate a vehicle that does not have a battery installed.

• Excessive engine cranking can damage a vehicle’s starter motor. If the engine

fails to start after the recommended number of attempts, discontinue jump-start

procedures and look for other problems that may need to be corrected.

• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.

• Although this unit contains a non-spillable battery, it is recommended that unit be

kept upright during storage, use and recharging. To avoid possible damage that

may shorten the unit’s working life, protect it from direct sunlight, direct heat and/

or moisture.

SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

Never leave the compressor unattended while in use.

WARNING – BURSTING ARTICLES CAN CAUSE SERIOUS INJURY:

• Carefully follow instructions on articles to be inflated.

• Never exceed recommended pressures. If no pressure is given, contact article

manufacturer before inflating.

• Monitor the pressure at all times on the pressure gauge.

CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE:

Do not operate compressor continuously for longer than approximately 10 minutes,

depending on ambient temperatures, as it may overheat. In such event, compressor

may automatically shut down. Turn off the Compressor Power Switch immediately

and restart after a cooling down period of approximately 30 minutes.

SPECIFIC SAFETY INSTRUCTIONS FOR THE USB POWER

PORTS

• Do not insert foreign objects into the USB Power Ports.

• Do not attach USB hubs or more than one personal electronic device to each USB

Power Port.

FIRST AID

When working with lead acid batteries, always make sure immediate assistance is

available in case of accident or emergency.

Always have protective eyewear when using this product: contact with battery acid

may cause blindness and/or severe burns. Be aware of first aid procedures in case of

accidental contact with battery acid.

Have plenty of fresh water and soap nearby in case battery acid contacts skin.

• Skin: If battery acid contacts skin or clothing, wash immediately with soap and

water for at least 10 minutes. If redness, pain, or irritation occurs, seek immediate

medical attention.

• Eyes: If battery acid comes in contact with eyes, flush eyes immediately, for a

minimum of 15 minutes and seek immediate medical attention.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Congratulations on purchasing your new Stanley®Fatmax®350 Amp Jump

Starter with Compressor. Read this Instruction Manual and follow the

instructions carefully before using this unit.

CHARGING/RECHARGING

Lead-acid batteries require routine maintenance to ensure a full charge and long

battery life. All batteries lose energy from self-discharge over time and more

rapidly at higher temperatures. Therefore, batteries need periodic charging to

replace energy lost through self-discharge. When the unit is not in frequent use,

manufacturer recommends the battery be recharged at least every 30 days.

IMPORTANT: If you know the unit is discharged, but the battery status LEDs

illuminate as if the unit is fully charged when connected to a charging power

source, this may be due to the internal battery having high impedance. The

manufacturer suggests leaving the unit charging for a period of 24-36 hours using

the supplied AC charger before use.

Notes: This unit is delivered in a partially charged state – you must fully charge it upon purchase and before

using it for the first time. Initial AC charge should be for 24 hours.

Recharging battery after each use will prolong battery life; frequent heavy discharges between

recharges and/or overcharging will reduce battery life. The battery can be recharged using the

supplied 120 Volt AC Charger.

Make sure all other unit functions are turned off during recharging, as this can slow the recharging

process.

CAUTION – RISK OF PROPERTY DAMAGE: Failure to keep the battery

charged will cause permanent damage and result in poor jump starting

performance.

WARNING: Never attempt to use the AC and DC charging methods at

the same time.

Charging/recharging using the 120 volt AC charging adapter

• Make sure all of the unit’s functions are turned off.

• Insert the barrel connector of the AC charging adapter into the 12 volt DC

charging port on the back of the unit. Insert the plug end into a (powered)

standard North American 120 volt 60Hz outlet.

• Once the green LED lights or flashes, continue to charge for approximately 1-2

hours. Charge until two red and one green LED Battery Status Indicators light

solid.

• Disconnect the AC charging adapter and depress the battery status button. If all 3

status lights illuminate, the unit is fully charged.

JUMP-STARTER

This Jump-Starter is equipped with an On/Off Power Switch. Once the connections

are properly made, turn the switch on to jump-start

the vehicle.

1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell

phone chargers, etc.). Place vehicle in “park” and set the emergency brake.

2. Make sure the Jump-Starter Power Switch is turned to off.

3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the

black clamp.

4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative

battery terminal is connected to chassis) (MOST COMMON)

4a. Connect positive (+) red clamp to vehicle battery’s positive terminal.

J7CS_J7CSC_ManualENSP_050520.indd 4-5J7CS_J7CSC_ManualENSP_050520.indd 4-5 5/6/2020 1:31:36 PM5/6/2020 1:31:36 PM