Star2Star Polycom OBi302 User manual

Polycom® OBi302
ATA Device Installation Guide
The Polycom® OBi302 is a two-port FXS Analog Telephone Adapter (ATA) device packaged in a compact chassis.
This device can be used for the following purposes:
●Fax machine on FXS port
●Local or remote phone on FXS port
Overview of the Installation Process
The OBi302 is normally pre-configured for use with our StarCloud+ and StarCloud telephone systems. In most
cases, the installer can connect the OBi302 to the customer’s network along with the appropriate analog
telephone connections.
Connecting the OBi302
The rear panel of the OBi302 has a power connection, USB connection, two RJ11 telephone connectors, and two
RJ45 network connectors, as shown in the following picture:
OBi302 Rear View
August 2019
Copyright © 2019, Star2Star Communications®, LLC. All rights reserved. Star2Star is a registered trademark of Star2Star
Communications, LLC. All logos and company names are trademarks or service marks of their respective companies.

Polycom® OBi302 ATA Device Installation Guide
The connectors are used as follows:
Connector
Purpose
Phone
Connections for an FXS (station) device, such as an analog telephone or a fax machine.
USB
Not supported in Star2Star configuration.
LAN
Connection for a laptop computer. Use this connection for off-site configuration.
Internet
Connection to the local network (if used as a local device) or to a WAN connection (if used as a
remote device).
DC 12V
Power
Power connector. Connect the provided AC power supply here.
Note: Does not operate on Power over Ethernet (PoE).
The LAN port is only used to access the OBi302’s built-in configuration server from a connected laptop. This is
necessary when performing off-site configuration. After the device is configured, the LAN cable can be
disconnected.
Pre-Installation Configuration
Ensure that the OBi302 device is added to the customer system correctly using the portal. ATA devices are added
via the Multi-Extension Devices  page in the portal. Analog Phone and Fax Extensions are configured via the
Extensions  page in the portal. For more information, refer to the ATA Portal Configuration Guide.
The OBi302 can be configured for either local (On-Net) or remote (off-net) use. If you are re-deploying an OBi302
that was already configured, follow the instructions in the Factory Reset  section below. Then, configure the device
for either local or remote operation.
If you are unsure about the current configuration, perform a factory reset and then configure the device using the
ATA Portal Configuration Guide.
Factory Reset
To factory reset the OBi302 ATA device:
1. Unplug the cable from the WAN or LAN port.
2. Locate the small raised hole on the bottom of the unit, near front left corner.
3. Insert a straightened paper clip or other thin tool into the hole, and press for about ten seconds. Once
removed, the device resets to the factory settings.
Page 2

Polycom® OBi302 ATA Device Installation Guide
StarCloud+ Locations
Configure as a Local Device
To configure the OBi302 ATA device as a local device:
1. Connect the WAN port to the telephony switch, which is the switch connected to LAN2 and LAN3 on the
StarBox® Voice Optimized SD-WAN.
2. Connect power supply. The device automatically downloads configuration and completes registration.
Once registered, the OBi302 can make and receive inbound and outbound calls.
Note: Automatic configuration download only applies to the standard StarBox installation.
Configure as a Remote Device
The OBi302 can operate as a remote device, but it requires installation-specific configuration information to
operate. For assistance, contact Star2Star Technical Support.
StarCloud Locations
Configure as a Local Device
To configure the OBi302 ATA device as a local device:
1. Connect the WAN port to the network.
2. Connect power supply. The device contacts the ZTP server, automatically downloads configuration, and
completes registration.
Once registered, the OBi302 can make and receive inbound and outbound calls.
Configure as a Remote Device
To configure the OBi302 ATA device as a remote device:
1. Connect the WAN port to the network.
2. Connect power supply. The device contacts the ZTP server, automatically downloads configuration, and
completes registration.
Once registered, the OBi302 can make and receive inbound and outbound calls.
Page 3

Polycom® OBi302 ATA Device Installation Guide
OBi302 Status Lights
The following status lights are available on the OBi302 front panel:
Light
Green Light Indicates
Connected to power.
Connected to a WAN connection.
Connected to a LAN connection.
Phone is connected and off-hook.
OBi302 Front View
Page 4