STC Gazebo GZ3584 User manual

of 221
www.stcny.com
Systems Trading Corporation
Customer service: [phone] Email: easy[email protected]
9’3”
12’2”
8’10”
9’11”
13’2”
7’
Assembly Instructions
Gazebo GZ3584
Aluminum Composite Roof Panels

of 222
www.stcny.com
Introduction
Thank you for purchasing the Gazebo GZ3584.
When properly assembled and maintained, this gazebo will provide many years of enjoyment!
These instructions include helpful hints and important information needed to safely assemble and properly
maintain the gazebo. Please read these instructions completely before you begin.
Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of
four people. The assembly should take about two hours.
Before Starting Assembly:
CAREFULLY READ ALL THE INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE
STEPS IN THE ORDER THEY ARE PRESENTED.
1. Make sure you have all the necessary parts:
Compare the contents of the two cartons to the List of Parts. If any parts are missing or damaged, or
you have any questions, please contact Customer service: [phone] before beginning assembly.
2. Lay the parts out in separate staging areas:
The List of Parts has the corresponding step number referenced to each part. We recommend that
while you go through the list, make staging areas for each step and place the parts necessary for
 eachstepintheseareas.Thiswillsaveyoutimeandeortduringassembly.
3. Select a Location:
 Whenselectingalocationforyourgazebo,aatlevelareaisessentialandifpossiblewithproper 
water drainage and easy access to power and water, if neccessary.
Choose a sunny, level position away from overhanging trees and power lines and protected from the
wind as much as possible.Locate underground pipes or cables before preparing the site or anchoring
the gazebo.
 Note:Youmayassemblethegazeboonahardlevelsurfaceandmoveittoitsnallocationwhen 
 nished.Makesurethattherearenoobstaclesbetweentheassemblyareaandthenalposition.
4. Prepare a Foundation:
After choosing a location, proper preparation of the site is recommended. The site must be level.
If the site is not level, create a base slightly larger than the outside dimensions of the gazebo using a
 perimeteroftwobyfourslledwitheithersoil,sodorgravel.
Make sure the base is square by measuring the diagonals from both directions and making sure
they are equal. The gazebo is secured with pegs into holes cast with concrete.
 Ifyoudecidetohaveaconcretebase,itisbesttocontactareliablecontractortomakesureitisat
and level. Make sure you have checked with your local authorities regarding any required building
permits.
5. Make sure you have the proper tools:
• Tape Measure • 2 Small Step Ladders
• Work Gloves • Wooden Mallet
• Safety goggles • Scissors
• Phillips Screwdriver • Liquid soap or WD40 Lubricant
• Spirit Level • Hex Key (included)
NOTE: A cordless drill with Phillips head bit is highly recommended but not essential.

of 223
www.stcny.com
1
1
5
5
5
5
1
1
2
34
67
7
Safety Advice
• Thegazebomustbepositionedandxed
onaatlevelsurface.
• Dispose of all plastic bags safely. Keep
them out of the reach of children.
• Keep children and pets away from the
assembly area until the work is completed.
• Always wear shoes, gloves and safety
goggles when working.
• Take special care not to touch overhead
powerlineswiththealuminumproles.
• Do not attempt to assemble the gazebo in
windy or wet conditions.
• Do not position your gazebo in an area
exposed to excessive wind.
• If using power tools or a ladder, always fol-
low the manufacturers safety instructions.
• Hot items such as recently used grills,
blowtorches etc. must not be stored in the
gazebo.
• Make sure the gazebo complies with local
building codes.
Table of Contents
Introduction.............................................. 2
Table of Contents...................................... 3
List of Parts............................................... 4
Step 1AssemblingtheCornerProles......... 6
Step 2AssemblingtheRoofProles............. 7
Step 3 AttachingtheRoofProlestoCornerProles .. 8
Step 4 Attaching the Roof Connectors............ 9
Step 5 Securing the Gazebo to the Ground..... 11
Step 6 Installing the Roof Gables.................... 12
Step 7 Installing the Roof Panels.................... 17
ATTENTION:
DO NOT ATTEMPT TO ASSEMBLE
THE GAZEBO
ALONE!

of 224
www.stcny.com
List of Parts
The gazebo is shipped in two cartons. These cartons are heavy. Be careful when lifting them.
Wear proper safety gear including work shoes, gloves and goggles.
Thepartsareidentiedbyremovablestickers.
Place all the parts for each step in staging areas, checking that you have all parts as you go.
If any parts are missing or damaged, contact STC customer service before beginning assembly:
Customer service: [phone]
2170mm
1584mm
1580mm
Aluminum Composite Roof Panel
black
side
2000mm
1650mm
1500mm
No. Part Qty Step
1 4 1
2 4 1
3 2 2
4 2 2
5 2 2
62 2
7 8 4
8 2 6
No. Part Qty Step
9 1 6
10 4 6
11 6 6
12 2 6
12A 1 6
13 4 7
14 6 7
15 4 7
2200mm
1150mm

of 225
www.stcny.com
Aluminum Composite Roof Panel
black
side
black
side
Aluminum Composite Roof Panel
Aluminum Composite Roof Panel
black side
Aluminum Composite Roof Panel
black side
black
side
Aluminum Composite Roof Panel
No. Part Qty Step
26 34 7
27 12 6
28 10 7
29 32 7
30 4 6
31 4 1
32 12 5
33 1
34 12
5
35 1
36 4
4
37 1 6
No. Part Qty Step
16 4 7
17 2 7
18 1 6
19 4 7
20 4 7
21 2 7
22 8 4
23 4 4
24 10 7
25 79
We included some extra screws and bolts for your convenience.

of 226
www.stcny.com
x 4
x 4
Cornerprole(1)
x 4 Cornerprole
cover (31)
x 4
Support plate (2)
x 4
Screw (25)
x 12
1
1 1 1 1
1
1
2
2 2 2 2
2
31
25
25
25
1.A
1.B 1.C
AssemblingtheCornerProles
Place all the parts on a level surface .
Make sure the pieces are in the correct positions before assembling.
Carefully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes, gloves and goggles.
Placecornerproles(1)paralleltoeachother
on the ground. Slide support plates (2) into
cornerprolesfromtheendwithasingle
screw hole, as shown.
Fasteneachplatetoproleusing
three screws (25).
Insertcornerprolecovers(31)
intotopendsofcornerproles(1)
as shown.
STEP 1
Components
x 4

of 227
www.stcny.com
2121212121
5
2121212121
5
2121212121
5
2121212121
5
2121212121
5
2121212121
5
2121212121
5
2121212121
5
2121212121
5
Roofprole(5)
x 2
Roofprole(6)
x 2
2.A
2.B
AssemblingtheRoofProles
Place all the parts on a level surface. Make sure the pieces are in the correct positions
before assembling. Carefully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes, gloves and goggles.
Insertendoflongroofprole(3)
intolongroofprole(4)asshown.
Fasten with screws (25).
Repeat to make two sets.
Insertendofshortroofprole(5)intoshortroofprole(6)asshown.Fastenwithscrews(25).
Repeat to make two sets.
STEP 2
Components
Roofprole(3)
x 2
Roofprole(4)
x 2 Screw (25)
x 8
3
4
6
4
4
25
25
3
5
56
3
x 2
x 2

of 228
www.stcny.com
Screw (29)
x 32
Components
ILLUSTRATION
3
4
3
4
3.A
3.B
Attachlongroofprolesets(3,4)tocornerproles(1)asshown.
Fasten with screws (29).
Repeat to make two sets.
Attachshortroofprolesets(5,6)tocornerproles(1)
as shown.
Fasten with screws (29).
29
29
29
31
1
1
1
1
1
1
1
1
1
1
5
5
5
6
6
3
4
4
3
3
STEP 3
AttachingRoofProlestoCornerProles
3

of 229
www.stcny.com
Components
3
3
3
6
5
5
4
4
6
1
31
4.A
Attaching the Roof Connectors
toRoofandCornerProles
Attach one roof connector (23) to
eachcornerprolecover(31)and
three roof connectors (22) to each
roofproleset(3,4)and(5,6)as
shown.
Fasten with screws (25).
STEP 4
25
25
25
25
25
25 25
25
25
25
25
25
25
22
25
23
23
31
31
31
31
23
23
22
22
22 22
22
23
22
22
22
VIEW FROM INSIDE
GAZEBO
Screw
(25)
x36
Roof connector
(22)
x8
Roof connector
(23)
x4
Roof connector
(7)
x8
Roof corner
connector(36)
x4

of 2210
www.stcny.com
7
7
Attachfourroofcornerconnectors(36)togazebocornersontopofproles(3,4,5,6)asshown.
Fasten with two screws (25) each.
25
34
36
36
36
36
25
3 / 5
4 / 6
IMPORTANT: After this step you should place the gazebo frame in its desired location.
Make sure all corners are squared at 90 degrees.
4.B
4.C
Attachtworoofconnectors(7)toeacheachroofproleset(3,4)and(5,6)asshown(facingoutwards).
Fasten with two screws (25) each.
3
3
3
3
6
6
5
5
5
5
4
4
4
4
6
6
25
7
7 7
7
7
7
7

of 2211
www.stcny.com
Components
Concrete screws, washers and nuts (32)
x 12
Wood Screws, washers x 12
NOT SUPPLIED
to be purchased by user
1. 2. 3.
Securing the Gazebo to a Concrete Floor or Wood Deck
Optional
Concrete Floor:
1.Usinganelectricconcretedrill,drillholesintotheconcreteoor,
corresponding to the holes in the support plates.
2. Insert concrete screws (32) into the holes and hammer into place, using a mallet.
3. Fasten concrete screws with washers and nuts.
Wood Deck:
1.Usinganelectricwooddrill,drillholesintothewoodoor,
corresponding to the holes in the support plates.
2.
Insert wood screws with washers (not supplied) into the holes and fasten,
using an electric screw driver.
Securing the Gazebo to the Ground
STEP 5
Components
32
32
32
1
2
5.A
Fasten the gazebo frame to the ground, using three spikes (32)
for each support plate.
Ground spike (32)
x 12

of 2212
www.stcny.com
8
8
8
8
9
9
25
25
25
37
12A
Screw (27)
x 12
Roof top cover (18)
x 1
12A
Installing the Roof Gables
STEP 6
Components
Roof top
end (8)
x 2
Roof top (9)
x 1
Roof top connector
(12A)
x 1
Roof support
(12)
x 2
Roof gable (10)
2170mm
x 4
Roof gable (11)
1584mm
x6
Screw (25)
x 23
6.A
Attach roof top connector (12A) to roof top (9) and fasten with screw (25) from the top.
Insert roof top ends (8) into both sides of roof top (9) and fasten with screws (25) from underneath.
Attach hook (37) from underneath.
Washer (30)
x 4
Hook (37)
x 1

of 2213
www.stcny.com
Using at least three people, install the roof gables (10,11,12) in the following order:
VIEW FROM TOP
6.B
11
10
12
5.
5.
11
91111
10 10
1010 1111 12
11 12
1.
1.
2.
2.
3.
3.
4. 4.
4.4.
IMPORTANT:
Theroofgableproles(10,11)havepre-drilledscrewholesunderneathoneachend.
The end with the shorter distance to the screw hole is connected to the roof top ends (8) and
the end with the longer distance to the screw hole is connected to the roof connectors (22,23).
Toward roof top ends (8,12A) Toward roof connectors (22,23)

of 2214
www.stcny.com
11
11
11
11
11
11
6.C
ILLUSTRATION
Usingscrews(25),rstconnectfourroofgableproles(11)torooftopends(8)
Then use screws (27) to attach their other ends to roof connectors (22) as shown.
9
9
8
8
8
22
22
22
25 25
27

of 2215
www.stcny.com
ILLUSTRATION
1 1
Usingatleasttwopeople,slideroofgableproles(10,11)intotunnelsofrooftopends(8)and
attach with screws (25) from underneath.
Then use screws (27) to attach their other ends to roof connectors (22,23) as shown.
Usescrews(25)toattachroofgableproles(10)toroofconnectors(36)fromunderneathas
shown.
6.E
11
11 11
11
8
8
8
27
23
36
25
25
10 10
10
10
10
10
10
Usingscrews(25),rstconnectfourroofgableproles(11)torooftopends(8)
Then use screws (27) to attach their other ends to roof connectors (22) as shown.

of 2216
www.stcny.com
6.F
9
27
25
12
12
12
12A
12A
6.G
Attach roof top cover (18) to roof top ends (8) on roof top (9) and fasten
with four screws (25) and washers (30) from the top as shown.
25
25
30
30
9
IMPORTANT: After this step you should place the gazebo frame in its desired location.
Make sure all corners are squared at 90 degrees.
IMPORTANT: After this step you should place the gazebo frame in its desired location.
Make sure all corners are squared at 90 degrees.
22
18
Attachroofsupportproles(12)toroofconnector(12A)onrooftop(9)andfastenwithscrews(25)
from underneath. Attach their other end to roof connectors (22) using screws (27).

of 2217
www.stcny.com
Screw (28)
x 10
Roof gable cover (13)
x 4
Roof gable cover (14)
x6
Screw(26)
x 20
Roofpanel(16)
x 4
Roof panel (20)
x 4
black
side
black
side black
side
black
side
Roof panel (15)
x 4
black
side
Roof panel (19)
x 4
black
side
Installing the Roof Gables
STEP 7
Components
Slide roof panels (17,21) into
their positions as shown.
Secureroofpanel(21)toroofsupportprole(12)
from below, using screw (28) through hole
inundersideofprole(12).
7.A
7.B
Installing the Roof Panels
Roof panel (17)
x 2
Roof panel (21)
x 2
Remove protective plastic from both sides of roof panels.
Place side to face toward the sun facing out when installing.
17
12
12
21
21
28
17
21
VIEW FROM THE TOP
VIEW FROM BELOW
(from underside of roof)
12

of 2218
www.stcny.com
20
7
28
14
11
20
15
17
17
12
21
21
ILLUSTRATION
26
14
11
Slide roof panel set (15,20) into position as shown.
7.C
7.D
Fasten roof panels (15,20) to connectors (7) from below with screws (28).
VIEW FROM THE TOP
15
20
Placeroofgableprole(14)ontopofroofgableprole(11).
Alignbothproles.
Frombelowthegazeboroof,xroofgablecover(14)
toroofgableprole(11)usingscrews(26)
through pre-drilled screw holes at mid point
andendofprole.
11
11
1111
11 10
10
10
10

of 2219
www.stcny.com
19
7
28
14
10
13
20
19
1516
17
21
ILLUSTRATION
Slideroofpanelset(16,19)intopositionasshown.
7.F
7.E
Fastenroofpanels(16,19)toconnectors(7)frombelowwithscrews(28).
VIEW FROM THE TOP
Placeroofgableprole(13)ontopofroofgableprole(10).
Alignbothproles.
Frombelowthegazeboroof,xroofgablecover(13)
toroofgableprole(10)usingscrews(26)
through pre-drilled screw holes at mid point
andendofprole.
Continue in a clock-wise direction
all around the gazebo roof.

of 2220
www.stcny.com
Components
18
14
11
14
24
End Cover
(24)
x 10
STEP 8
11
ILLUSTRATION
7.G
7.H
Slideupperendoflastprole(14)underrooftopplate(18)asshownandlowertheproleto
tintoroofgableprole(11).
Frombelowthegazeboroof,xroofgablecover(14)toroofgableprole(11)usingscrews(26)
throughpre-drilledscrewholesatmidpointandendofprole.
Close each assembly with end covers (24).