Steelcraft Dolce User manual

Art No.4001411
2010 Copyright Britax Childcare Pty. Ltd. Australia
BRITAX CHILDCARE PTY. LTD A Britax International company.
(Incorporated in Victoria) A.B.N. 55 006 773 600
99 Derby Road, Sunshine, Victoria 3020, Australia
Phone: [phone] Fax: [phone]
CUSTOMER SERVICE
1300 303 330 - Australia 0508 688 822 - New Zealand
Due to our continuing program of development, Britax reserves the right to alter
the specifications, color or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty.Ltd - Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: www.britax.com.au or email us at [email protected]
Due to the variations in the style and design of our products the illustrations used
in this instruction booklet are generic.
This product is designed to comply with Australian Standard AS 4684-2009
Series No. YS 89-1
Dolce Hi-Lo High chair
IMPORTANT!
KEEP FOR FUTURE REFERENCE

23
KEEP FOR FUTURE REFERENCE
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY
AND USE OF THIS HIGH CHAIR. ALWAYS FOLLOW THE
INSTRUCTIONS. THE CORRECT USE AND MAINTENANCE
OF THIS PRODUCT IS ESSENTIAL.
WARNINGS THE CHILD SHOULD BE
SECURED IN THE HIGH CHAIR AT ALL TIMES BY THE
HARNESS, EITHER IN THE RECLINING OR UPRIGHT
POSITION. THE TRAY IS NOT DESIGNED TO HOLD THE
CHILD IN THE CHAIR. IT IS RECOMMENDED THAT THE
HIGH CHAIR BE USED IN THE UPRIGHT POSITION ONLY
BY CHILDREN CAPABLE OF RELIABLY AND
CONSISTENTLY SITTING UPRIGHT UNASSISTED.
WARNINGS
: PREVENT SERIOUS INJURY OR DEATH.
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• DO NOT LEAVE CHILDREN UNATTENDED.
• THE HARNESS MUST ALWAYS BE USED AND
CORRECTLY FITTED. - MOST INJURIES FROM THE HIGH
CHAIRS ARE CAUSED BY FALLS.
• POSITION THE HIGH CHAIR AWAY FROM SOLID
STRUCTURES AND BENCHES TO AVOID INJURIES
CAUSED BY FALLS AND ACCESS TO DANGEROUS ITEMS.
• Double check assembly before placing child into high chair.
• The weight of the child using this product is not exceed 15kg.
WARNINGS CARE AND MAINTENANCE
• To prolong the life of your high chair keep it clean and do not
leave it in the direct sunlight for extended periods of time.
• Remove fabric covers and trims may be cleaned using warm
water with household soap or mild detergent. Allow it to dry
fully, preferably away from the direct sunlight.
• Non removable fabric covers and trims may be spot cleaned
using a damp sponge with soap or a mild detergent. Allow it
to dry completely before folding or storing it away.
• In some climates the covers and trims may be affected by
mould and mildew. To help prevent this occurring, do not fold
or store the product if it is damp or wet. Always store the
product in a well ventilated area.
• To maintain the safety of your nursery product, seek prompt
repairs for bent, torn, worn or broken parts. use only those
parts and accessories approved by Steelcraft.
• Always check parts regularly for tightness of screws, nuts
and other fasteners - tighten if required.
• If the high chair is not working correctly stop using the high
chair and seek repair.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.

• Always apply the brakes when not moving the high chair.
• Do not allow children to stand on the seat.
• Use on a flat , even and horizontal floor and never use near
stairs.
• Do not elevate the high chair on any structure or table.
• Do not allow child to stand on the seat.
• Never carry the high chair with the child in it.
• Do not use the high chair without the tray and always ensure
the tray is secure on the arm rests. The tray is not designed
to hold the child in the chair.
• When making adjustments to the high chair, ensure that you
and your child’s body, fingers and toes are clear of any
moving parts on the high chair, otherwise they may be injured.
• Position the high chair away from furniture, walls, hot surfaces
and liquids, window covering cords, electrical cords and
position the high chair away from furniture when the chair is
not being used at a table.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
03
22
WARNING Continued
NOTES

04 21
NOTES
PARTS LIST
A1 x Frame B2 x Lower Leg Moulding
D1 x Seat Support Bar
F1 x Base tray
1 x Removable tray
C1 x Seat Assembly
E 1 x Adjustable Footrest

05
20
PARTS LIST
G4 x Wheels H1 x Reversible Seat Insert
I1 x Snap Fastener
K1 x Basket
J6 x Phillip head Screws
12. TO USE THE HIGHCHAIR
• Place the high chair on a horizontal, flat and even floor
ensuring all wheels are in contact with the floor.
• The high chair must not be placed on a table or similar
surface to elevate the child.
• The high chair is fitted with brakes on two castors. Ensure the
brakes are applied when the child is in the high chair and only
release the brakes to move the high chair.
• If pushing the high chair on carpet, be careful that the high
chair is not pushed over as the castors may not roll easily on
the carpet.
• Position the high chair away from potential hazards and other
furniture or structures that the child may be able to grasp or
push.
• Keep away from walls, kitchen benches, hot surfaces, hot
liquids and electrical cords.

19
01. TO ASSEMBLE THE HIGHCHAIR
A Ensure that the seat supports are facing in towards the
middle between the front and rear legs. Ensure the labels
face inwards.
BIf the seat supports are facing out then swing both rear
legs outward 180˚ degrees to face the opposite way.
CPress the folding release buttons then slide them down
until they click into position.
11. TO FOLD/UNFOLD THE HIGHCHAIR (Cont)
BPress the folding release levers then slide them up until
they click into position. Ensure the frame has locked in
place and is secure. Attach the tray to the rear legs as
shown in Section 9.
To unfold the high chair, reverse Steps A and B.
CAUTION: ALWAYS STORE THE HIGH
CHAIR SO IT CANNOT BE PULLED OR FALL ON
CHILDREN.

10. TO RECLINE THE HIGHCHAIR 01. TO ASSEMBLE THE HIGHCHAIR
D Insert the leg mouldings onto the corresponding legs. Use
a phillips head screwdriver to install the screws and secure
the leg mouldings to the legs of the high chair.
E To install the seat assembly, align the locating tabs on
both sides of the seat assembly with the slots in the frame.
Ensure the seat assembly is installed in the correct
orientation as shown. When in position, hold the assembly
in place to prevent it from falling backwards.
18 07
ALift and hold the recline latch located on the back of the seat
and tilt the seat assembly back to the desired position.
WARNING: DO NOT ADJUST WITH THE
CHILD IN THE CHAIR.
11. TO FOLD/UNFOLD THE HIGHCHAIR
WARNING: DO NOT ADJUST WITH THE
CHILD IN THE CHAIR.
ARemove the child and tray from the high chair. Release the
tray attachment arms by pressing in the trigger located on
the outside of each arm. Fold the arms up.

08 17
01. TO ASSEMBLE THE HIGHCHAIR (Cont)
FRotate the seat assembly until the two holes in the front of
the seat assembly align with the two holes in the frame.
Insert the seat support bar into the hole at the front right of
the frame and push it through the seat assembly and out
of the hole on the opposite side. Secure the seat support
bar with the snap on fastener. Ensure the seat assembly is
securely fitted.
GTo install the footrest, align the footrest with the locating
tabs on the lower front of the seat and slide the leg rest
all the way in until it latches in place.
KInstall in each upper corner of the footrest 2 of the screws
supplied.
09. TO ADJUST THE HEIGHT OF THE HIGHCHAIR
ARemove the child and tray from the high chair.
BStand at the front of the high chair and press the height
adjustment levers on both sides and either push the chair
up or down to the desired height. Check the height
adjustment levers on both sides have locked into place to
ensure secure engagement of the seat assembly.
WARNING: DO NOT ADJUST WITH THE
CHILD IN THE CHAIR.

01. TO ASSEMBLE THE HIGHCHAIR (Cont)
HTo attach the wheels, insert the pin of each wheel
assembly into the corner of leg mouldings and push in to
secure. Two of the wheel assemblies are fitted with brakes
which will prevent the high chair from moving. Place the
wheels with the brakes to the rear of the high chair.
16 09
Wheel without brake
Wheel with brake
07. TO ATTACH AND USE THE TRAY (Cont)
EWhen the tray is not in use you can store the tray by
sliding it onto the pegs located on the rear legs.
Please Note: Before using the tray, check it is securely
locked onto the arm rests by pulling on the tray.
08. TO ADJUST THE FOOTREST
ALower the footrest by pressing up on the release latches
located underneath the footrest on both sides.
Raise the leg support by lifting it until the release latches
lock into place.

03. TO USE THE BRAKES
10 15
02. TO ATTACH THE BASKET
AAttach the basket hangers onto the studs at both sides of
the seat back.
BAttach press studs over the frame support bar under the
seat.
APress down on the brake lever to lock the brakes.
BPush the brake lever up to unlock the brakes.
WARNING: ALWAYS APPLY THE BRAKES
EXCEPT WHEN MOVING THE HIGHCHAIR.
07. TO ATTACH AND USE THE TRAY (Cont)
CAlign both tray slots with the arm rests and slide the tray
back onto the arm rests to the desired position and release
the tray latch ensuring it has locked into position. The
position of the tray can be adjusted by pulling forward the
release and sliding the tray to the desired position.
DThe tray features a removable second tray for convenient
cleaning. Remove by releasing both tabs on the left and
right side of tray.

04. TO SECURE YOUR CHILD IN THE HARNESS
AA five point harness is provided to restrain your child.
To secure your child in the harness please follow the steps
below carefully.
Push buckle (A) and (B) into the buckle housing (C) until
the buckle prongs snap into position.
Carefully adjust the harness by pulling the slider (D) until
the desired fit is achieved in the lap, shoulder and crotch
straps.
Always adjust the harness when changing the seating
position of the child.
To remove the child, release the buckle by squeezing the
top and bottom prongs, remove the shoulder straps and
lift the child out of the high chair.
WARNING: USE THE HARNESS AT ALL
TIMES.
07. TO ATTACH AND USE THE TRAY
AEnsure the tray attachment arms are lowered and locked.
WARNING: THE TRAY IS NOT DESIGNED
TO HOLD THE CHILD IN THE HIGHCHAIR. THE CHILD
IS TO BE SECURED BY THE SAFETY HARNESS AT
ALL TIMES WHILE IN THE HIGHCHAIR.
BPull forward the release latch of the tray which is located
under its front edge.
CAUTION: Ensure the child’s hands are free from moving
parts when the tray is being attached or removed to avoid
pinching or entrapment.
14

12 13
05. TO ADJUST THE SHOULDER STRAPS
PLEASE NOTE: The shoulder straps can be positioned at
two heights. Choose a shoulder strap height that is close
to the child’s shoulders.
AThe shoulder straps are secured to the back of the high
chair with a screw. To change the shoulder strap height,
undo the screw and push the webbing end through the slot
and then insert into the next slot. Pull the shoulder strap
through the back of the high chair. Ensure the webbing
end sits flat against the slot in the backrest moulding.
Insert the screw through hole in the harness and into the
plug and tighten to secure shoulder strap to the back of
the high chair.
PLEASE NOTE: The crotch strap and the waist straps also
have a webbing end. Ensure webbing end sits flat against
the slot moulding. The crotch strap and waist straps are
also secured to the high chair with a screw. To remove
undo the screw and push the webbing end through the slot.
06. TO INSTALL THE PADDED SEAT INSERT
ATo install the padded seat insert, release the harness
buckles and disconnect the harness shoulder straps from
the waist straps and install the padded seat insert. Pull
the shoulder straps, waist straps and crotch strap through
the slots in the insert. Reconnect the shoulder straps to
the waist straps. Ensure that the slots on the insert align
with the shoulder strap position on the backrest.