ComfyBumpy BEDSIDE CRIB User manual

BEDSIDE CRIB
INSTRUCTIONS
Consumer Assistance
Your happiness matters to us and we want to hear from you.
Please contact us for any reason.
www.ComfyBumpy.com
[email protected]
734 7 Ave SW #810, Calgary, AB T2P 3P8 Canada
IMPORTANT! Please keep these instructions for future reference
• Read all instructions before assembling and using the product.
• Assemble product according to manufacturer’s instructions for ANY use mode—bedside sleeper
as well as the bassinet mode.

WARNING
Failure to follow these warnings and the instructions could result in
serious injury or death.
• SUFFOCATION HAZARD
Infants can suocate:
• in gaps between an extra pad and the side of the product.
• on soft bedding.
NEVER add a mattress, pillow, comforter, or padding. Use ONLY the pad
provided by ComfyBumpy™.
• FALL HAZARD - To prevent falls, DO NOT use this product when the infant
begins to push up on hands and knees or has reached 25 lb (11.3 kg), whichever
comes first.
• To avoid death from the infant’s neck being caught on the top rail on the side
that is next to the adult bed, the top rail must be no higher than the adult bed
mattress.
• Strings can cause strangulation! NEVER place items with a string around a
child’s neck such as hood strings or pacifier cords. NEVER suspend strings over
product or attach strings to toys.
• NEVER place product near a window where cords from blinds or drapes can
strangle a child.
• To reduce the risk of Sudden Infant Death Syndrome (SIDS), pediatricians
recommend healthy infants be placed on their backs to sleep, unless otherwise
advised by your physician.
• If a sheet is used with the pad, use only the one provided by the bassinet or
cradle manufacturer or one specifically designed to fit the dimension of the
bassinet or cradle mattress.
1

IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Comfy-
Bumpy™ for replacement parts and instructions if needed. Never
substitute parts. •Please read these instructions before assembly
and use of this product.
•Adult assembly is required. No tools required for assembly.
•Product features and decorations may vary from photographs.
2

Leg Frame
Mattress
Carriage Carry Bag
Assembled Parts
3

Crib Assembly
Unfold The Legs
1. Press in outer buttons located on the top of the frame
2. Simultaneously open the legs (is easier if you have a second person to
lend a hand)
3. Ensure the legs are spread as much as possible and both sides have
clicked in
1 2 3
4

Attach The Crib
1. Open the arms of the carriage
2. Feed the arms into the legs
3. Adjust the height by squeezing the hand-held button
1
3
2
5

Stand Alone Crib Mode
1. Push in the sliding plastic clip around the base (under the crib)
2. Ensure the button has snapped through the clip
3. Do on the other side and double-check it is sturdy
1. Pull up on side bar and click in both corners
2. Zip up both corners so flap is tightly closed
Study Mode - Locking The Base
6

Incline Bed For Acid Reflux Setup
1. Ensure product is in ‘Stand Alone Crib’ mode
2. Ensure product is in ‘Sturdy Mode’
3. Adjust one side of the crib up by 1 Level
4. Place baby’s head on taller side
7

8
Rocking Mode – Unlocking The Base
1. Ensure product is in ‘Stand Alone Crib Mode’ and not in ‘Bed Side Crib
Mode’
2. Press in the button in on the sliding plastic clip
3. Pull the sliding plastic clip towards the middle of the crib
4. Ensure it is pulled all the way in and clicks in
5. Lightly rock by pushing on the bottom of the of the crib
2 3 4

9
Bed Side Crib Mode
1. Unzip corner flaps
2. Pull up on corner buttons to release side bar and bring down flap
3
1
2

10
Bed Measurement & Crib Height Setup
Measure Bed Height & Crib Height Setup
1. Measure bed height
2. Adjust crib to correct level by pulling up on the hand-held button
3. Ensure the crib side wall closest to the bed is not higher than the mattress
4.Ensure the crib is horizontal so both numbers on the arms are the same and
the crib is not in incline mode
WARNING: To avoid death from the infant’s neck being caught on the top rail
on the side that is next to the adult bed, the top rail must be no higher than
the adult mattress. ALWAYS raise the side when not fastened to the adult bed.

11
Attaching Straps
Check To Ensure Product Is Secure
1. Insert the two ‘Male Buckles’ into the
two ‘Female Buckles’
2. Feed the strap underneath the mattress
3. Tighten the strap which is located near
the plastic blocker
4. Ensure the plastic blocker is flush and
tight with the mattress
1. Make sure the crib is sturdy by pulling on the crib away from the bed
2. If it is loose, check to make sure that the crib is in ‘Sturdy Mode’ and that
the strap is tight from the plastic blocker all the way to the clips

12
Entrapment Hazard - To prevent death from entrapment, bedside sleeper must be
properly secured to adult bed using the attachment straps.
• There must be no more than 1/2 Inch (13mm) gap between bedside sleeper and
adult bed
• Check tightness before each use by pulling bedside sleeper in a direction away
from adult bed.
• If gap exceeds 1/2 inch (13mm), DO NOT use product. Do not fill the gap with
pillows, blankets or other items that are suocation hazards
WARNING

13
Entrapment Hazard - To prevent death from entrapment, bedside sleeper must be
properly secured to adult bed using the attachment straps.
• There must be no more than 1/2 Inch (13mm) gap between bedside sleeper and
adult bed
• Check tightness before each use by pulling bedside sleeper in a direction away
from adult bed.
• If gap exceeds 1/2 inch (13mm), DO NOT use product. Do not fill the gap with
pillows, blankets or other items that are suocation hazards
WARNING

14
WARNING
WARNING: The 2 attachment straps must always be used in bedside sleeper
mode.
Removing From Bed Frame
1. Unbuckle both straps
2. Remove straps from under bed
3. Put into ‘Stand Alone Crib Mode’

15
Ensure your baby is not inside the crib
when you detach the crib from your bed
frame.
Moving With Wheels
1. Lift one side of the crib approximately 20 degrees to roll on hard floors.
Note: We did not create wheels large enough to roll on carpet to avoid any
risks associated with a moving crib. The wheels are meant to move from room
to room if needed.
WARNING: Ensure your baby is not inside the crib when you move the crib.
Mattress Dimensions
31.9” x 18.8” x 1.18” (81 cm x 47.8 cm x 3 cm)
Replacement mattresses can be purchased by contacting ComfyBumpy:
[e-mail]
Never replace mattress from any company other than ComfyBumpy to ensure
safety.
Urine Sheet
When spills or leaks are likely to happen, put down the urine sheet to avoid
getting the mattress cover dirty.
WARNING:Do not leave urine sheet with baby unattended to avoid suocation.
Washing Instructions
Mattress & Siding: Sponge with mild detergent
Urine Sheet: Machine washable (air dry)
WARNING

16
Bedside Crib Disassembly
Disassemble & Fold Crib
1. Put crib into ‘Rocking Mode’
2. Pull up on the hand-held button to the highest level for each side
3. Find the button located in between the metal leg and the crib
4. Press in the button and lift it so the arm is out of the leg base for each side
5. Pull out the frame and separate it from the mattress
4. Press in top buttons located on the outside of the legs
5. Simultaneously close the legs
Putting Crib Into Carry Bag
1. Slide closed legs in with the plastic side facing first
2. Slide mattress on top
3. Slide crib base on top
4. Zip up

17
Pediatricians and child health organizations agree that healthy babies should be placed on
their backs to sleep for naps and at nighttime, to reduce the risk of Sudden Infant Death
Syndrome (SIDS). But babies who are always on their backs can sometimes develop flat
spots on their heads (plagiocephaly). Most cases of positional plagiocephaly can be
prevented (and sometimes corrected) by repositioning your baby to relieve pressure on the
back of the head. Here are some tips and techniques from the experts to keep in mind as
you care for your baby:
• Change the location of your baby’s sleeper or crib in the room, so she has to look in
dierent directions to see the door, or the window, or interesting things going on around
her.
• When your baby is awake, provide opportunities for adult-supervised “tummy time” play.
Playing on his tummy helps take the pressure o the back of his head, which will help
prevent flat spots from developing. Tummy time play also helps your baby’s head, neck and
shoulder muscles get stronger as part of normal development.
• Try tummy time two or three times a day, for short periods of time, until your baby gets
used to being on her tummy. Once your baby begins to enjoy this position, try longer
periods of time or increase the frequency of tummy time play.
• Help your baby avoid resting his head in the same position all the time by frequently
changing the direction he lies in the crib. For example, have your baby’s feet point toward
one end of the crib for a few days, and then change the position so his feet point toward
the other end of the crib. This will encourage your baby to turn and look in dierent
directions.
• Try to minimize the amount of time your baby spends in car seats, carriers and bouncy
seats while awake.
• Lastly, make sure you enjoy lots of “cuddle time” with your baby by holding her upright
over your shoulder. For additional information on positional plagiocephaly and the benefits
of tummy time play for your baby, speak with your pediatrician or family physician.
National Institute of Health (NIH) Eunice Kennedy Shriver National Institute of Child Health
and Human Development.
Preventing Baby’s Head from Flattening
1. Lift one side of the crib approximately 20 degrees to roll on hard floors.
Note: We did not create wheels large enough to roll on carpet to avoid any
risks associated with a moving crib. The wheels are meant to move from room
to room if needed.
WARNING: Ensure your baby is not inside the crib when you move the crib.
Mattress Dimensions
31.9” x 18.8” x 1.18” (81 cm x 47.8 cm x 3 cm)
Replacement mattresses can be purchased by contacting ComfyBumpy:
[e-mail]
Never replace mattress from any company other than ComfyBumpy to ensure
safety.
Urine Sheet
When spills or leaks are likely to happen, put down the urine sheet to avoid
getting the mattress cover dirty.
WARNING Do not leave urine sheet with baby unattended to avoid suocation.
Mattress & Siding: Sponge with mild detergent
Urine Sheet: Machine washable (air dry)

Thank You!
Give your baby a hug from all of us at ComfyBumpy.☺
If there’s anything we can help with, we will. Whether you are just having a tough
day or you need help with a product, we love to hear from our customers.
And hey, if you’ve got a cute photo of your little one in our products, we love
receiving those too.
www.ComfyBumpy.com
[e-mail]
734 7 Ave SW #810, Calgary, AB T2P 3P8 Canada