STEELWOOD SSW-10S-1200 User manual

1
STEELWOOD WET AND DRY VACUUM CLEANER
INSTRUCTION MANUAL
SSW-10S-1200
Before using the vacuum cleaner, please read this manual carefully and save it

2
The description and introduction of vacuum cleaner
1) Usage of the handle Picture 1
Pull out the plastic clips and then bend the fingers naturally holding the handle to lift up the machine head.
2) Usage of the switch
Turn off the "o" for power off. Turn on the "-" for power on
3) Hanging wire function
After using, hang the wire here for storage; put the plug into the groove to ensure the plug is clean.
4) Usage of the clips Picture 2
Follow the picture (2), press the top part of the clips to pull out, open and remove the machine head.
5) The connection method for hose Picture 3
Insert the hose connector into the suction mouth, and then rotate about 90°to make it tightly locked.
6) Blowing function
Check the hose inner is clean before use. Insert the hose connector into the blowing mouth and tighten it, then to use
this blowing function.
7) Accessories function Picture 4
Storage the accessories as the picture (4) show.
picture 1 picture 2
picture 3 picture 4

3
Filter’s dies-assembly and assembly (HEPA)
Picture 1 Picture 2 Picture 3 Picture 4

4
1) Take off the machine head. Picture 1
2) Clockwise twist the bottom cover of the HEPA filter, then take off the HEPA. Picture 2
3) Wash and dry it. Picture 3
4) Put the dry HEPA filter back, anticlockwise twist the bottom cover tightly. Picture 4
Filter’s dis-assembly and assembly (Cloth Filter)
Picture 1Picture 2 Picture 3 Picture4
1) Take off the machine head. Picture 1
2) Take off the cloth filter. Picture 2
3) Wash and dry it. Picture 3
4) After clean and dry, put the filter and head back. Picture 4
Instructions after use
1) Turn off the power switch."o" for turn off, "-" for turn on.
2) Pull out the plug and tidy up the wire.
3) Remove the hose and floor brush, and clean the dust which still inside the hose.
4) Remove the head.
5) Remove the filter, clean and dry it carefully for next use.

5
6) Clean the dust barrel and dry it with a rag.
1 2 3
6 5 4
Protective device - Special notes on safety buoys
when the water in the barrel is full, the buoy starts working, and suction power stops at this
time, and an abnormal sound will appear, indicating that the motor runs at a high speed. In this
situation, you should cut off the power as soon as possible and pour off the water which in the
barrel. After installing the whole machine and turning on the power again, the vacuum cleaner
will rework normally.
When the vacuum cleaner turns or shakes violently, the buoy will take effect and the power
should be cut off immediately. After the buoy returns to normal, you can turn on the power again
and use the vacuum.
When the buoy starts working, it will reduce the motor life when use vacuums in this situation.
In this case, stop using it and use it after you drain the water.

6
Raising of water level
Cleaning and maintenance
Diagram of cloth filter Diagram of HEPA filter

7
Before cleaning, please turn off the power and pull off the plug.
Methods of cleaning:
1) Use brush to clean the dust on the filter.
2) Use tap or shower washes the filter from inside to outside for better clean.
3) Put the filter in a well-ventilated place to air-dry it. Store it properly for your next
use.
Note: After washing the filter
1) Be sure of intensive drying (To avoid bad smell or block).
2) Does not use air blower or another kind of hot-blast air drying it (To avoid
causing failures due to out of shape).
3) Do not use detergent/bleach/thinner/alcohol etc.(To avoid causing cracks and fading color.
For security purpose, please pay attention to the following items:
Do not collect fire or inflammable etc. (To avoid fires or explosion) like
cigarette/gasoline/printing ink/thinner etc.
Do not use it when the plug or cable is damaged. (To avoid causing fire because of
overheating).
Do not wash by water (besides washable parts). Do not use it in bathroom etc.damp
environment. Do not dis-assembly, repair or transform itby yourself (To avoidfires or electronic
shock). The appliance can not be used by children or persons who has defects on physical/
sensory/mind, or lack of experience and knowledge(Unless they under supervision or
instruction).

8
Do not use wet hands to pull out the plug (To avoid electric shock).
Correct use of the plug. Please ensure the plug has insert into the socket tightly(To avoid
electric shock or fires).
Please use AC socket separately (To avoid causing fires when it work together with
other machines).
Pull out the plug before your maintain (To avoid electric shock).
Confirm the filter is installed when it working (To avoid the motor burning).
Please cut off the power and remove the plug when there are failures
happen.(To avoid causing smog/fires or electronic shock)
Example of failures
⚫The appliance is not working even you open it
⚫The machine is out of shape or hot
Please check and repair it to the designed center in time
⚫When you pull the plug or wire sometime there is electricity and sometime not
⚫The hose is damaged
⚫Burnt smell
⚫Quit work suddenly
⚫Abnormal voice during your usage

9
ATTENTION to avoid fire or hurt etc.
1) Do not move it when the clips are un-clocked. (To avoid damages when you moving it.)
2) Use the wire and plug in a correct way. Please pull out the plug when not use it.(To avoid the
bad insulationcausing electricshock/theleakage of electricity or fires )
3) Avoid incorrect operation:
Do not put metal into the connectorof this machine (To avoid electric shock).
Do not pull the plug by the wire.
Do not pull or move the machine bypulling the hose(To avoid damages cause by falling). Please
use the handle to move orpull it.
Please keep it a proper distance away from fire/heat source or sunlight.(To avoid fire or out
of shape).
Operate Requirements - To prolong the working life time
Please not collect the followingthings in case caused breakdown orbad smell.
Dehumidizer
Massive of powder(constructionwaste/powder of fire extinguisher)
Pet excreta etc.
Glass/tins/needles/toothpicks
Something easy to block the Hose(ropes/stockings)
Please use the hose carefully (to avoid it damaged)
To avoid the motor overheating please not use it continually morethan half an hour, otherwise
this mayreduce its working life time.
When the tank is full of dust
When the suction mouth is blocked

10
When the hose, tube, nozzle is blocked
Please not use the hose or the tube to collect dustdirectly to avoid wear. Please use the floor
brush or crevice nozzle etc.
Please not block the air-outlet(To avoid out of shape caused by overheating).
Please do not continually use it, when the suctionmouth is blocked.
Please check whether the cloth or HEPA filter wasinstalled before using(To avoid the waste go
into the motor directly,caused the burning).
Troubleshooting
Before commissioning repairs, please confirm the following items
◼The machine does not work
⚫Check that the power plug is firmly plugged into the outlet.
⚫Check if the power outlet has electricity.
◼Suction is weakened
⚫Check if the plastic hose and metal hose are blocked.
⚫Check if the filter is not clean or blocked.
⚫Check whether the body is changed, fastened.
⚫Check if the air filter is blocked.
⚫Check whether the air volume adjustment switch of the wind adjustment elbow is in an
open state.
◼The sound becomes louder when running, or a loud sound or abnormal sound is
generated
⚫The filter is blocked.
⚫Hose, long pipe, nozzle is blocked.
If the fault can't be solved by the above method, please send it to the designated maintenance
point for repair. Do not disassemble and repair it by yourself.

11
How to properly handle this product
The European market has instructed us that this product cannot be discarded as easily as other
household utensils. In order to prevent the improper disposal of this product from possible harm
to the environment and human beings, we have a duty to make its recycling a usable material
resource. You can send scrapped products to the recycling center or to the recycler at the place of
purchase. They will be safe and will not affect the recycling of the environment.
Guarantee Information
The manufacturer provides the same guarantee time as the customer's country. The guarantee
period is 1 year.
Guarantees only including products that materials & quality are failed.
Repairs during the warranty period will be performed by the manufacturer's certified service
provider.
Customers have to provide a bill (Including purchase date) for the purchase of this product to be
repaired during the warranty period.
The following circumstances will not guarantee:
Normal wear, incorrect use such as: Exceeds the product load, Use uncertified accessories,
violent use, other improper use, not reading instructions carefully, not properly connected
accessories, not installed correctly according to the manual, partially or completely dismantled
products etc.
Specification
Model
Power (W)
Voltage (V)
RATE (HZ)
SW-10S-1200
1200W
220V-240V
50/60HZ