STEINWAY LYNGDORF CDP-1 User manual

MODEL CDP-1
SERIAL CONTROL MANUAL
VERSION 1.0
[Skriv tekst]

TABLE OF CONTENTS
TABLE OF CONTENTS......................................................................................2
INTRODUCTION.................................................................................................3
COMPLIANCE ....................................................................................................3
SERIAL SETTINGS.............................................................................................4
COMMAND AND REQUEST FORMATTING......................................................4
REQUESTS ........................................................................................................5
COMMANDS.......................................................................................................7
TRADEMARKS...................................................................................................9
SERVICE INFORMATION ................................................................................10
2

INTRODUCTION
This Installation Manual was created to assist you with setting up and using your Steinway Lyngdorf
electronics and accessories.
Please read all material carefully prior to installation or first use of your Steinway Lyngdorf product. If
you need additional assistance, contact your Steinway Lyngdorf representative or email
[e-mail].
COMPLIANCE
WEEE
The European Parliament and the Council of the European Union have issued the Waste
Electrical and Electronic Equipment Directive. The purpose of the Directive is to prevent
waste of electrical and electronic equipment and to promote reuse, recycling, and other
forms of waste recovery. Steinway Lyngdorf products and the accessories packed with them are
subject to the WEEE Directive. Please dispose of any waste materials in accordance with your local
recycling regulations. Products and equipment which must be collected for reuse, recycling, and other
forms of recovery are marked with the icon of the crossed-out waste receptacle.
FCC
Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference; and (2)
this device must accept any interference received, including any interference that may cause
undesired operation. Model A1/A2 amplifier and Model P1 processor contain TX FCC ID:
TYOJN5139M0
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. Equipment marketed to a consumer must be capable of
complying with the necessary regulations in the configuration in which the equipment is marketed.
3

SERIAL SETTINGS
The serial port settings are always 8 data bits, no parity and one stop bit with a baud rate of 115200.
COMMAND AND REQUEST FORMATTING
All commands and requests start with the ‘!’ character. Commands end with a combination of the
Carriage Return character (ascii 0x0D, referred to as <CR> in this document) and Line Feed (ascii
0x0A, <LF>). Often, a single <CR> is used, but because different systems handle these characters
differently, it is also allowed to end with <LF>, <CR><LF> or even <LF><CR>. In this document, it is
expected to be <CR><LF>, but all of these combinations are allowed.
Requests end with the character ‘?’ and <CR><LF> (or any <CR><LF> combination as above).
Commands can have parameters; these are enclosed in parentheses.
Replies to a request are formatted as the request with the reply values as parameters. Replies always
use the <CR><LF> combination of line-end characters.
Commands and requests are not case sensitive.
In addition, it is possible to subscribe to status changes from the device. In this situation, whenever a
status has changed (new state, new track etc.) the device will send a status. This status is formed
exactly like a reply to a request, except it is followed by the character '!' before the <CR><LF> to
indicate that this is an asynchronous message, not a reply.
!COMMAND<CR><LF>
Command
!COMMAND(param)<CR><LF>
Command with parameter
!REQUEST?<CR><LF>
Request
!REQUEST(reply)<CR><LF>
Reply to a request
!REQUEST(status)!<CR><LF>
A status which has changed
Commands and requests which are malformed or have invalid parameters will be ignored. If a
command or request is correct but followed by garbage before the line end character(s), the
command or request will be executed and the garbage ignored.
4

REQUESTS
The following requests are available on the CDP-1:
Request name
Action
Reply
!VER?<CR><LF>
Requests the SW version
in the CDP-1
!VER(1.23a)<CR><LF>
If the version is 1.23a
!STATE?<CR><LF>
Requests the current
state.
One of:
!STATE(OFF)<CR><LF>
!STATE(OPENING)<CR><LF>
!STATE(OPEN)<CR><LF>
!STATE(CLOSING)<CR><LF>
!STATE(NODISC)<CR><LF>
!STATE(DISCERROR)<CR><LF>
!STATE(READING)<CR><LF>
!STATE(PLAY)<CR><LF>
!STATE(STOP)<CR><LF>
!STATE(PAUSE)<CR><LF>
!STATE(WIND)<CR><LF>
!STATE(REWIND)<CR><LF>
!TRACK?<CR><LF>
Requests the number of
the track currently being
played.
From
!TRACK(1)<CR><LF>
to
!TRACK(99)<CR><LF>
or
!TRACK(-)<CR><LF>
if no track is currently being played
!NOFTRACKS?<CR><
LF>
Requests the number of
tracks on the current
disc.
From
!NOFTRACKS(1)<CR><LF>
to
!NOFTRACKS(99)<CR><LF>
or
!NOFTRACKS(-)<CR><LF>
if there is no current disc.
!TIME?
<CR><LF>
Requests the elapsed
time of the playing track.
Reply format:
!TIME(1:23)<CR><LF>
or
!TIME(-0:01)<CR><LF>
where the '-' indicates, that the CDP-1 is currently in
the pause between tracks, counting down to start.
5

!REMTIME?<CR><LF>
Requests the remaining
time of the current track.
Reply format:
!REMTIME(3:21)<CR><LF>
or
!REMTIME(-0:01)<CR><LF>
where the '-' indicates, that the CDP-1 is currently in
the pause between tracks, counting down to start.
!PLAYMODE?<CR><L
F>
Requests the current play
mode.
!PLAYMODE(m), where m is one of:
0 = Normal play mode
1 = Repeat disc
2 = Repeat track
3 = Random play
!TRACKNAME?<CR><
LF>
Requests the trackname
from cd-text info for the
current track.
!TRACKNAME(Name Of Track)<CR><LF>
or
!TRACKNAME()<CR><LF>
if no data is present for the track name.
!TRACKARTIST?<CR>
<LF>
Requests the trackartist
from cd-text info for the
current track.
!TRACKARTIST(Artist Name)<CR><LF>
or
!TRACKARTIST()<CR><LF>
if no data is present for the track artist.
!DISCNAME?<CR><LF
>
Requests the discname
from cd-text info for the
current disc.
!DISCNAME(Name Of Disc)<CR><LF>
or
!DISCNAME()<CR><LF>
if no data is present for the disc name.
!DISCARTIST?<CR><L
F>
Requests the discartist
from cd-text info for the
current disc.
!DISCARTIST(Artist Name)<CR><LF>
or
!DISCARTIST()<CR><LF>
if no data is present for the disc artist.
6

COMMANDS
The following commands are available on the CDP-1.
Command name
Action
!OFF<CR><LF>
Turns the CDP-1 off.
!ON<CR><LF>
Turns the CDP-1 on.
!PWR<CR><LF>
Toggles power on the CDP-1. Same functionality as the
standby button on the front.
!EJECT<CR><LF>
Opens or closes the tray. Same functionality as the eject button
on the front.
!PLAY<CR><LF>
Play.
!PAUSE<CR><LF>
Pause.
!PLAYPAUSE<CR><LF>
Toggles between play and pause. Same functionality as
pressing the rotary button on the front.
!STOP<CR><LF>
Stop.
!PREV<CR><LF>
Requests the previous track. If the disc is currently at track 1,
the last track on the disc will be selected. Same behavior as
turning the front rotary knob counter-clockwise.
!NEXT<CR><LF>
Requests the next track. If the disc is currently at the last track,
the first track on the disc will be selected. Same behavior as
turning the front rotary knob clockwise.
!REWIND<CR><LF>
Start scanning backwards.
!WIND<CR><LF>
Start scanning forwards.
!STOPWIND<CR><LF>
Stop the scanning started by one of the above commands.
!DIGIT(d)<CR><LF>
Corresponds to pressing the digit d on the remote in order to
select a specific track.
!PLAYMODE(m)<CR><LF>
Select playmode, where m is one of:
0 = Normal play mode
1 = Repeat disc
2 = Repeat track
3 = Random play
!DISPMODE(m)<CR><LF>
Selects display mode, where m is one of:
0 = Elapsed time, no CD-Text info.
1 = Remaining time, no CD-Text info.
2 = Elapsed time, CD-Text info active.
3 = Remaining time, CD-Text info active.
7

!SAMPLERATE(r)<CR><LF>
Selects a new samplerate for the output, where r is one of:
1 = 48 kHz
2 = 96 kHz
3 = 192 kHz
!SUBSCRIBESTATE<CR><LF>
Start subscription mode for the state of the CDP-1. Will send
information whenever the state changes.
!UNSUBSCRIBESTATE<CR><LF>
Deactivates state subscription mode.
!SUBSCRIBETRACK<CR><LF>
Start subscription mode for track numbers. Will send
information whenever a new track number is available
!UNSUBSCRIBETRACK<CR><LF>
Deactivates track subscription mode.
!SUBSCRIBETIME<CR><LF>
Start subscription mode for time. Will send information
whenever new time info is available. If the current display mode
displays remaining time, then the time send from the CD will
also be remaining time.
!UNSUBSCRIBETIME<CR><LF>
Deactivates time subscription mode.
!SUBSCRIBEDISCTEXT<CR><LF>
Activates disc text subscription mode. Whenever a new disc is
inserted, the disc name and disc artist will automatically be
sent.
!UNSUBSCRIBEDISCTEXT
<CR><LF>
Deactivates disc text subscription mode.
!SUBSCRIBETRACKTEXT
<CR><LF>
Activates track text subscription mode. Whenever a new track
is being played, track artist and track name will automatically be
sent.
!UNSUBSCRIBETRACKTEXT
<CR><LF>
Deactivates track text subscription mode.
8

TRADEMARKS
DTS is a registered trademark & the DTS logos and Symbol are trademarks of DTS, Inc.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD Master Audio are trademarks of DTS, Inc. © 1996-
2014 DTS, Inc. All Rights Reserved.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
This product incorporates technology that is protected by U.S. patents and other intellectual property
rights. Use of this technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
This item incorporates copy protection technology that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
9

SERVICE INFORMATION
In order to obtain warranty service you must contact your original dealer or the Steinway Lyngdorf
distributor of the region or country where you are located. If you have trouble locating an authorized
representative, please contact the Steinway Lyngdorf Customer Service Department using the contact
information at www.steinwaylyngdorf.com, or you may email [e-mail].
Steinway Lyngdorf
Ulvevej 28
DK 7800 Skive
Denmark
Service Hotline: [phone]
Fax: [phone]
In some cases, the Customer Service Department may solve a service problem without the need of
repair or any other measures, thereby avoiding further inconvenience or delay. In some cases it may
be necessary to return the equipment to Steinway Lyngdorf or an authorized service provider for
repair; therefore, it is recommended that you save your original packing materials. Steinway Lyngdorf
will not be responsible for any damage due to unauthorized packing or shipment in non-original
packing materials. If return is made in authorized packaging, risks are borne by Steinway Lyngdorf.
Additional charges may occur if new packing materials are required for return shipment.
10