stilum Flova cala User manual

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for playpoint without impact protection
„ova cala“
Item No. 51 3410 401
State: 28.05.2020 p. 1
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for playpoint without impact protection
„ova cala“
Item No. 51 3410 401
State: 28.05.2020 p. 2
1. Select the location of the play equipment taking into account the required
minimum space (see diagram 3: Ø 3500 mm).
2. Carry out excavation work for the foundation as shown in diagram 2. After
excavation, compress the foundation oor.
Note: The playpoint is installed at play level.
3. Set up the concrete foundation according to diagram 2 with central, horizontal
reinforcement. Pour the supplied foundation anchor in the foundation so that
the upper angle frame is horizontal and ush with the foundation surface.
4. After a setting period of 10 – 14 days, depending on weather conditions and
foundation size, ll up and compress the holes between the foundation and
the foundation hole with the excavation.
5. Clean the surface of the foundation. Place the play equipment on the founda-
tion anchor and screw it down. Create topsoil.
Recommended surface material: optional, with the exception of sand
Note: The ground should be smooth and free of edges.
6. Do not allow children to use the equipment before the installation has been
nished.
Reinforcement plan: Concrete foundation with reinforcement
Main foundation: BSt 500S
Stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C20/25
Diagram 2: Foundation plan
Play level
Foundation anchor
Concrete foundation
500
500
350
850 1800
153
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
1
flova cala
Benennung
Gepr.
Blatt
Datum
Projekt
Gez.
Zeichnungsnummer
1:15
A3
Name
Name
Fundamentplan
1501-00-00
Maßstab
Behnke 16.11.2016
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
concrete
gewachsenes Erdreich
natural ground
Legende
stoßdämpfender Boden
shock-absorbing floor
SI 06.05.20 beliebiger Boden A
DatumÄnderungRev
beliebiger Boden
optional floor

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for playpoint without impact protection
„ova cala“
Item No. 51 3410 401
State: 28.05.2020 p. 3
3500
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
1
flova cala
Benennung
Gepr.
Blatt
Datum
Projekt
Gez.
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Name
Name
Draufsicht
1501-00-00
Maßstab
Behnke 16.11.2016
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Note for the temporary disassembly:
7. Remove the 4 screws beneath the standing position (see diagram 4a).
8. Take out the stucked pipe.
Note: 180mm of the pipe still protrudes and poses a tripping hazard.
9. Cover the remaining pipe with the plastic cap included in the delivery (see
diagram 4b).
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to particu-
lar risks of injury for the user. For this reason, make clearly visible that the equip-
ment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel should
not come with „normal“ steel parts in contact. Those steel parts may rub o󰀨 and
leave small steel particles in combination with moisture brown rust stains. If such
corrosion occur on stainless steel parts, they are ne with an abrasive (240 grit) to
remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
Diagram 3: Top view
Area of the
minimum space

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for playpoint without impact protection
„ova cala“
Item No. 51 3410 401
State: 28.05.2020 p. 4
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse o󰀨 with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the playground equipment at
intervals of three to six months.
Diagram 4a: Temporary
disassembly
Diagram 4b: Rain protection
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
flova cala
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:8
A3
Gewicht
Name
Name
Draufsicht
1501-00-00
Maßstab
Simonis 13.01.20
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
flova cala
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:8
A3
Gewicht
Name
Name
Draufsicht
1501-00-00
Maßstab
Simonis 13.01.20
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland