stilum curvus User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for merry-go-round „curvus“
Item No. 51 4015 401
State: 09.03.2017 p. 1
·
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for merry-go-round „curvus“
Item No. 51 4015 401
State: 09.03.2017 p. 2
·
Diagram 2: Side view with dimension details „curvus“
Play level
Floor anchor
Concrete foundation
1. Select the play equipment location in consideration of the required safety
area (see Diagram 3: Ø 5350mm).
2. The impact area of a playground equipment with an enforced movement is
not allowed to overlap the impact area of other equipment.
Regarding to DIN 1176 - 4.2.8.2.5, impact absorbing surfaces have to be put
under the whole impact area of every equipment with an enforced movement.
3. Carry out excavation work for the foundation anchor as shown in Diagram 2.
After excavation, compress the foundation oor.
Note: The roundabout is built in on the play level. Pay attention to items
marked „game level“ of play equipment!
The distance of the playing surface to the bottom of the hub has to be
60 mm at minimum and a maximum of 110 mm!
4. Set up the concrete foundation acc. to the dimensions indicated
(LxWxH 800 x 800 x 500 mm) with central, horizontal reinforcement (BST 500
S) in the quality class B 25. Make sure that the foundation anchor included
in the delivery is cast into the foundation in such a way that the upper angle
frame lies horizontally and ush mount with the surface of the foundation.
Reinforcement plan: Concrete foundation with rein-
forcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class B25
500
800
1326
80
mind. 60mm
max. 110mm
Erde
Ground
Füllmaterial
Filling
Beton
Concrete
Blatt:
Projekt:
Artikelnummer:
ZG-NR:
BENENNUNG:
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
FREIG:
GEPR:
GEZ :
DATUM:
NAME:
WERKSTOFF

MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
+0,3
-0,3
WERKSTUECKKANTEN
NACH DIN 6784
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A3
1
0203-00-00
514015401
Ø1326x671.5
Fertigung:
Mattheis
Gewicht:
174074.46
Curvus
Zust. Änderung Name
Abmaße:
Zuschnitt:
Fundament
Datum
20.07.16
A
Abstandsmaß korrigiert Behnke 10.02.2017

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for merry-go-round „curvus“
Item No. 51 4015 401
State: 09.03.2017 p. 3
·
5. After the setting time of 10-14 days, depending on weather conditions and
foundation size, clean the surface of the foundation and put the pre-mounted
play equipment onto the foundation anchor. Screw out the locking screw with
hexagon socket from the roundabout bottom. Use the opening in the rounda-
bout oor to screw the base plate of the play equipment onto the foundation
anchor. After that, close the opening in the roundabout bottom.
6. Existing gaps between the foundation and foundation hole lled up with exca-
vated soil and compact.
7. Seal the foundation with the safety cover required for the height of fall indica-
ted. Set up impact-absorbing playground surfacing according to EN 1177 HIC
1000.
Critical drop height: 200mm
Recommended surface material: grass, sand, wood chip, gravel, synth. fall
protection
8. Do not allow children to use the equipment before the installation has been
nished.
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to par-
ticular risks of injury for the user. For this reason, make clearly visible that the
equipment shall not be used in such cases.
Diagram 3: Top view „curvus“
5350
Rev.:
Projekt:
BESTELL-NR:
ZG-NR:
BENENNUNG:
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
FREIG:
GEPR:
GEZ:
DATUM: NAME:
Unlegierter Baustahl
WERKSTOFF

MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
+0,3
-0,3
WERKSTUECKKANTEN
NACH DIN 6784
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A3
0026-00-00
30.03.2016
Abmaße:
-
Fertigung:
Behnke
1x
Gewicht:
179070.0
curvus
Draufsicht
Extent of the mini-
mum zone = safety
area

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for merry-go-round „curvus“
Item No. 51 4015 401
State: 09.03.2017 p. 4
·
NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may rub
off and leave small steel particles in combination with moisture brown rust stains.
If such corrosion occur on stainless steel parts, they are ne with an abrasive
(240 grit) to remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the playground equipment at
intervals of 3 to six months.