stilum papilio3 User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „papilio3“
Item No. 51 3016 401
State: 15.06.2016 p. 1
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „papilio3“
Item No. 51 3016 401
State: 15.06.2016 p. 2
Diagram 2: Side view with dimension details „papilio3“
Play level
Floor anchor
Concrete foundation
1. Select the play equipment location in consideration of the required safety area
(see Diagram 3: Ø 5300mm).
2. The impact area of a playground equipment with an enforced movement is not
allowed to overlap the impact area of other equipment.
Regarding to DIN 1176 - 4.2.8.2.5, impact absorbing surfaces have to be put
under the whole impact area of every equipment with an enforced movement.
3. Carry out excavation work for the foundation anchor as shown in Diagram 2.
After excavation, compress the foundation oor.
Note: The springrider is built in on the play level. Pay attention to items
marked „game level“ of play equipment!
4. Concrete foundation acc. the specied dimensions (LxBxH 1000 x 1000 x 500
mm) build with centrally mounted, horizontal reinforcement. It shed the sup-
plied anchor bolts with the foundation that the upper angle frame is horizontal
and ush with the foundation surface.
5. During the setting time of 10-14 days, depending on weather conditions and
foundation size, lock the play equipment.
6. After the setting period clean the surface of the foundation, place the pre-
mounted play equipment onto it and screw the base plate of the play equip-
ment onto the foundation anchor.
Reinforcement plan: Concrete foundation with rein-
forcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class B25
500
1000
440
516
910
Fundamentplan
Beton
Concrete
Erde/Grund
Ground
Füllmaterial
Filling
0061-00-00
papilio3
Rev.:
Projekt:
BESTELL-NR:
ZG-NR:
BENENNUNG:
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
FREIG:
GEPR:
GEZ:
DATUM: NAME:
WERKSTOFF

MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
+0,3
-0,3
WERKSTUECKKANTEN
NACH DIN 6784
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A3
04.02.2016
Abmaße:
Fertigung:
Behnke
x
Gewicht:
500
1000
440
516
910
Fundamentplan
Beton
Concrete
Erde/Grund
Ground
Füllmaterial
Filling
0061-00-00
papilio3
Rev.:
Projekt:
BESTELL-NR:
ZG-NR:
BENENNUNG:
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
FREIG:
GEPR:
GEZ:
DATUM: NAME:
WERKSTOFF

MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
+0,3
-0,3
WERKSTUECKKANTEN
NACH DIN 6784
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A3
04.02.2016
Abmaße:
Fertigung:
Behnke
x
Gewicht:

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „papilio3“
Item No. 51 3016 401
State: 15.06.2016 p. 3
Diagram 3: Top view „papilio3“
7. Seal the foundation with the safety cover required for the height of fall indica-
ted. Set up impact-absorbing playground surfacing according to EN 1177 HIC
1000.
Critical drop height: 550 mm
Recommended surface material: grass, sand, bark mulch, gravel,
synth. fall protection
8. Do not allow children to use the equipment before the installation has been
nished.
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to particu-
lar risks of injury for the user. For this reason, make clearly visible that the equip-
ment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel should
not come with „normal“ steel parts in contact. Those steel parts may rub off and
leave small steel particles in combination with moisture brown rust stains.If such
corrosion occur on stainless steel parts, they are ne with an abrasive (240 grit) to
remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
Extent of the mini-
mum zone = safety
area
5300
0061-00-00
Draufsicht
papilio3
Rev.:
Projekt:
BESTELL-NR:
ZG-NR:
BENENNUNG:
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
FREIG:
GEPR:
GEZ:
DATUM: NAME:
WERKSTOFF

MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
+0,3
-0,3
WERKSTUECKKANTEN
NACH DIN 6784
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A3
04.02.2016
Abmaße:
Fertigung:
Behnke
x
Gewicht:

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „papilio3“
Item No. 51 3016 401
State: 15.06.2016 p. 4
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type and
degree of soiling as well as on demands made on optical characteristics. Therefore
cleaning is advisable at intervals of six to twelve months – whereby in the case of
strong soiling it is appropriate to clean the playground equipment at intervals of 3
to six months.