stilum Jump circleL Operating and maintenance instructions

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 22.01.2019 S. 1
Maintenance instruction bouncing element „jump circleL“
Item-No. 51461x240
Visual inspection (1 - 3 weeks):
• Check for loss or vandalism
• Check the surfaces of metal and plastic for sharp-edged elements, scratches,
cracks or similar and, if necessary, grind or renew
• Replace missing parts
• Remove dirt and other objects (stones, broken glass, etc.)
Operational (1 - 3 month) - and main inspection (annually)
• Check for loss or vandalism
• Check the surfaces of metal and plastic for sharp-edged elements, scratches,
cracks or similar and, if necessary, grind or renew
• Replace missing parts
• Remove dirt and other objects (stones, broken glass, etc.)
• Check moving parts for easy operation
• Check all fasteners and attachments for tightness and loss, tighten or replace
• Check screw connection and tighten if necessary
• Testing the stability of the device
• Check for traps
• Testing the fall protection coating.
Attention!
The maintenance intervals mentioned above are to be understood as recommen-
dations. The frequency of inspections has to be increased accordingly in case of
intensive use of the equipment, extreme weather conditions, installations near the
coast or in places which are often subject to vandalism and depending on the age
of the equipment!
In addition to the maintenance recommendations given by the manufacturer, it is
also absolutely necessary to follow the regulations stipulated in DIN EN 1176-7!
When exchanging or repairing elements, please always use original spare parts
for the sake of operational safety and for liability reasons!
If the play equipment has been incompletely installed or partly dismantled when
carrying out maintenance and repair work, this may lead to particular risks of
injury for the user. For this reason, make clearly visible that the equipment shall
not be used in such cases!
Edit: 05.12.2018
Bouncing element Jump Circle L
Art. 013240
Installation and maintenance manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 22.01.2019 S. 2
Maintenance instruction bouncing element „jump circleL“
Item-No. 51461x240
• Clean complete game device (annually)
• Check chain links for abrasion (1/3 maximum permissible)
• Check ground clearance
• Check free space under the jump surface. Check frame for damage and
permanent deformation
Check free space under the jump surface
Using the hook tool available from stilum GmbH, loosen the springs of the boun-
cing mat and remove the mat. Remove all things on the combined frost protection
and load bearing layer. Take into account that the clearance height is complied
with in accordance with mounting instruction diagram 3. Visually inspect jump
devices for damage. Check the springs for damage and deformation.
The hook tool we attached to the fall protection. The hook points in the direction
of the spring. Insert the eye of the spring into the hook opening and tension the
spring by pulling on the lever. In doing so, move the thimble / holder down to
release the mat. Replace the mat in reverse order.
Note: If safety-critical serious defects are detected during an inspection, they
must be remedied immediately. If this is not possible, the system must be exclu-
ded from use, e.g. by decommissioning or dismantling.
If a piece of equipment needs to be removed, e.g. for maintenance or repair, all
anchors or foundations remaining in the ground should be removed or covered
with covers. The device should be locked for use.
The strength of the screw connection must be checked no later than 14 days
after installation. Loose connections need to be tightened.
14
Mit dem bei der Seilfabrik Ullmann erhältlichen
Hakenwerkzeug die Federn der Sprungmatte lösen und die
Matte herausnehmen. Alle auf der Sickerschicht
befindlichen Dinge entfernen. Berücksichtigen, dass die
Freiraumhöhe gemäß Kapitel 5 eingehalten wird.
Sprunggeräte visuell auf Beschädigungen prüfen. Kontrolle
der Federn auf Beschädigung und Verformung.
Bild 2: Hakenwerkzeug
15
Bild 3: Zum Lösen der Federn angesetztes Hakenwerkzeug
Bild 4: Gespannte Feder
15
Bild 3: Zum Lösen der Federn angesetztes Hakenwerkzeug
Bild 4: Gespannte Feder
Hook tool
Right using direction of tool
Bring tension on spring