stilum 55 1311 401 Technical specifications

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Maintenance instructions for „Chest-shoulder-press“
Item-No. 55 1311 401
State: 19.02.2019 p. 1
Attention!
The maintenance intervals mentioned above are to be understood as recommen-
dations. The frequency of inspections has to be increased accordingly in case of
intensive use of the equipment, extreme weather conditions, installations near the
coast or in places which are often subject to vandalism and depending on the age
of the equipment!
In addition to the maintenance recommendations given by the manufacturer, it is
also absolutely necessary to follow the regulations stipulated in DIN EN 16630
and DIN EN 1176!
When exchanging or repairing elements, please always use original spare parts
for the sake of operational safety and for liability reasons!
If the tness equipment has been incompletely installed or partly dismantled
when carrying out maintenance and repair work, this may lead to particular risks
of injury for the user. For this reason, make clearly visible that the equipment
shall not be used in such cases!
Quarterly operative inspection:
1. Check the exercise and movement area for obvious safety hazards and
cleanliness (e.g. exposed foundations, missing or damaged parts, missing or
insufcient impact absorption, broken pieces, dirt etc.).
2. Check the movement area for cleanliness and damages. Protruding ele-
ments, if there are any, have to be removed. If necessary ll up the installati-
on depth to the mark „ground level“.
3. Check the equipment for cleanliness, correct functioning, wear, stability and
damages. Check all the xing elements and retighten them if necessary. In
case of damages, replace the damaged elements.
Annual main inspection
(in intervals of not more than 12 months):
In addition to the checks of the operative inspection, pay special attention to the
stability of the equipment (which may be affected due to corrosion or vandalism)
and its operational safety, especially after repair works or after mounting new
elements or replacing existing elements. For that purpose, it may be necessary to
uncover the foundations.

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Maintenance instructions for „Chest-shoulder-press“
Item-No. 55 1311 401
State: 19.02.2019 p. 2
In order to preserve a good visual appearance of your stilum tness equipment
over a long period one should take care of maintenance of the stainless surface
even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the tness equipment at inter-
vals of 3 to six months.
Maintenance
The weigth components (sliding weigths) are generally maintenance free. How-
ever, their condition should be checked for damage every six months and repla-
ced if necessary.
Spare parts
Spare parts are available for parts that become worn through normal use, for
example: seats, balls etc. These parts should be regularly inspected every year
for wear and tear and replaced if necessary.