Stone Forest PFS-TD-36 WSD6 Series User manual

with 6"h wood drawer and wood shelf
circle one: CLASSIC FACET
©2021 Stone Forest, Inc.
DO NOT SCALE DRAWING
ood finish___________________
DWG. NO.
stand finish___________________
PFS-TD-36-xx-WSD6
Elemental Console Vanity 36"
PFS-TD -36 WSD6 - Elemental Console Vanity 36
J
C
AA
B
B
C
D
D D
D
E
D
D
E
K
F
GG
H
H
I
part item code descri tion qty X
(A) PFS-TB-23 23” TUBE X2
(B) PFS-TB-18 18” TUBE X2
(C) PFS-TB-5 5” TUBE X2
(D) PFS-CLLR COLLAR/SET X3
(E) PFS-FOOT FOOT/SET X1
(F) PFS-KNOB KNOB w/ scr w X1
(G) PFS-TEE TEE X2
(H) PFS-WALL ESCUTCHEON X2
2" #8 scr ws - BR, MB or PN w/wall anchors [for part (h) abov ] X10
(I) PFS-DRWR-366 36"W DRAWER X6"D X1
(J) PFS-WDSLF-36 36"W WOOD SHELF X1
(K) PFS-BRKT-8 8” ANGLE BRACKET X1
¾” #8 scr ws - BR, MB or PN - for attachm nt of brack t to sh lf [part (J) &(K) abov ] X4
2” #8 scr ws-black w/ wall anchors - to attach draw r box and sh lf to wall for parts
(I&J) abov ] X8
1"x1"x8" aluminum wall brack t with scr ws and anchors for attaching sink to wall -
suppli d wh n sink is ord r d with stand x2
allen wrench (1), white gloves (1pr), 2"x2"x6" spacers for installation (2), extra set screws (6), installation template (1)

Elemental Drawer
Floor level (see back of page for instructions on mounting higher up)
1. Using white gloves provided, carefully layout all brass or nickel fittings on a protected surface. Some assembly
will be required using the included allen wrench.
2. Start with the legs. The bottom collars and feet need to be installed
to support the drawer 4-8” from the ground depending on model and
preference. Carefully slide the legs through the drawer unit from the top and
then slide the collars on from the bottom followed by the feet. Tighten the
feet first and then set the collars so the distance from the bottom of the feet
to the bottom of the drawer (top of collar) is the same as the 2x2” supports
included.
3. Set the 2pcs of 2x2 wood supports against the back wall where the console supplied 2x2” (1 of 2)
is to be installed.
4. Move the drawer and legs into position with the rear of the drawer
being supported by the 2x2’s. At this time the drawer should be close to level,
but does not need to be exact. Remove the drawer from the cabinet box by supplied 2x2” (1 of 2)
depressing the tabs on the drawer glides (one pushes up, the other pushes
down) and level the back edge of the drawer (left to right)
Once level, use the supplied screws (and anchors if needed) to attach the cabinet
box to the wall. For the strongest installation, we recommend locating at least
one stud along the back of the cabinet and predrilling a 1/8” hole in the cabinet
back.
5. Once the drawer is attached securely to the wall you can level front to back and
left to right along the front edge by loosening the collars on the legs and moving
up or down slightly.

Elemental Drawer
Upper position (see front of page for instructions on mounting floor level)
1. Slide one collar onto each leg at the desired height for the bottom of the drawer.
2. Remove the drawer from the cabinet box by depressing the tabs on the drawer glides (one pushes up, the other
pushes down)
3. With the help of someone else, carefully slide the empty drawer cabinet down onto the brass legs being careful
not to twist it and scratch the legs.
4. Hold the unit level against the wall. Be sure to level left to right AND front to back. Once level, use the supplied
screws (and anchors if needed) to attach the cabinet to the wall. For the strongest installation, we recommend
locating at least one stud along the the back of the cabinet and predrilling a 1/8” hole in the cabinet back.
5. Once the drawer is attached to the wall, check for level again. Any fine tuning can be done at the front collars
using the provided allen wrench.
6. Insert the drawer back into the cabinet.

Elemental Wood Shelf
Floor level (see back of page for instructions on mounting higher up)
1. Using white gloves provided, carefully layout all brass or nickel fittings on a
protected surface. Some assembly will be required using the included
allen wrench.
2. Start with the front legs. The bottom collars and feet need to be installed
to support the shelf 4-8” from the ground depending on model and preference.
The height from the bottom of the feet to the top of the collars should be
the same as the supplied 2x2 wood supports.
3. Carefully slide the legs through the shelf from the bottom. supplied 2x2”s
We included 2pcs of 2x2 wood to help with the initial location of the shelf on
the wall. The height of these should match the height to the top of the collars.
4. Move the shelf and legs into position. Level the shelf along the back as
well as front to back (the front feet can be twisted to help). Once the
shelf is in position and leveled, mark the wall on the underside noting supplied 2x2” (1 of 2)
the position of the metal bracket. Move the stand from the wall, then
remove the bracket from the shelf and mount the bracket to the wall
where previously marked. Set the unit back into position onto the
bracket and attach.
5. Once the shelf is attached to the wall, check for level again. Any fine tuning
can be done at the front collars using the provided allen wrench.
6. Optional: slide additional collars onto legs to fit on top of the shelf.
(these are not supplied with the stand and should be purchased separately) additional collars

Elemental Wood Shelf
Upper position (see front of page for instructions on mounting floor level)
1. Slide one collar onto each leg at the desired height for your shelf.
2. Carefully slide the shelf down onto the front legs being careful not to twist the shelf and scratch the legs.
3. With the help of someone else hold the shelf level against the wall. Be sure to level left to right AND front to
back. Mark the wall on the underside noting the position of the metal bracket. Carefully remove the shelf, then
remove the bracket from the shelf and mount the bracket to the wall where previously marked. Set the shelf
back onto the legs and bracket and attach.
4. Once the shelf is attached to the wall, check for level again. Any fine tuning can be done at the front collars
using the provided allen wrench.

PFS-TD and PFT-ST
1. Using white gloves provided, carefully layout all brass or nickel fittings
on a protected surface. Some assembly will be required using the
included allen wrench.
NOTE: If you are installing the legs with other components, please
see the individual instructions for each component
2. Assemble the legs as shown.
On the underside of the sinks there are 2-4 recessed holes to accept
the top 3/8” of each leg. Measure the center to center distance on
the two front holes. This will be your measurement for locating the
center of each wall connection.
Set the legs up so they are plumb, level and square against the wall
and attach using the supplied screws and anchors (if needed).
If drilling into wood blocking or studs, please pre-drill the holes with
a 7/64” bit. This will help with the installation of the softer brass
screws. If going into drywall, use the supplied anchors and
pre-drill using 3/16” bit.
3. Install sink top and bracket according to the sink model.
The collars directly under the sinks do not support any weight.
These can be adjusted up against the sink bottom when you are
done with the final assembly.
Table of contents
Popular Indoor Furnishing manuals by other brands

Hiddenbed
Hiddenbed Double Decker Assembly instructions

SAUTHON easy
SAUTHON easy TOKYO XV631A Technical manual

KMART
KMART 43036592 Assembly instructions

OfficeSource
OfficeSource 1101HMF Assembly instructions

Argos
Argos Washington 425/8425 Assembly instructions

SANTA LUCIA
SANTA LUCIA IKONA Living Boiserie Assembly instructions

Schardt
Schardt Zirbe 06 263 Assembly instructions

Furniture of America
Furniture of America CM3188PT-40 Assembly instructions

fantastic furniture
fantastic furniture COMO ROBE 2 DOOR manual

Tuft & Needle
Tuft & Needle Contrast Platform Bed Care & assembly instructions

Tech Craft
Tech Craft PTV30B Assembly instructions

hygena
hygena 503/7968 Assembly instructions and user guide